EASY FIX DRILL CHUCK WOBBLE

[@daveyJ213]

Tried your technique on my old DeWalt DWD110 drill. Worked like a charm. Disassembled the case and found that the rear bearing (two on the chuck) was the one that was not seated in its slot. Borrowed some heavy duty tin foil from the kitchen, and layered up about 5 plies and cut it into strips and placed it in each half of the bearing housing. After the buttoning up the case the wobble is absolutely gone! Rock solid. Even my worst offending bit, a counter sink bit spins for the first time absolutely straight. You are what Sylvester the cat would call a "stuper sheenish". Thanks for posting. Now I don't have to purchase a new drill. By the way, the case housing had tons of super clean grease still inside the case. I just reapplied it and I'm good to go. Thank you Jhon!

[@kanishka.b8550]

I shattered one of my HSS bits while drilling throght metal and had a bad wobble... that’s why I searched this. But my drill is fairly new and under warranty... so I guess I need to contact the shop.! Thank you for the video.

[@notchipotle]

lol mine just came out from the box and it's already wobbles

[@jimchen2389]

Clear & well demo video. Exactly what I need. Almost throw away my drill. Thanks !

[@GNU_Linux_for_good]

01:18 *Master* ! Did you pull the plug *before* opening the case?

[@jhonarief]

that is for sure

[@GNU_Linux_for_good]

@@jhonarief *sweet relief* . You've fixed that pretty darn well.

[@jamesjennings3098]

Looks like it was plugged in the whole time! I hope not.

[@jhonarief]

If it is, I can not reply this😁, probably on the way to the hospital 🤪

[@truthfinder6999]

Thanks for this tip .Good video.

[@zazatava9058]

Sir, my problem is the chuck has less grip when drilling, even though I replaced with new one & tightening it before drilling. In your opinion, what's is the problem?

[@jhonarief]

If that the case i think you need to replace the chuck

Hello my friend. I liked the idea of correcting the balancing curvature on the drill. Congratulations. Thank you for sharing. See you. big greetings. stay healthy and happy.

[@HibikiKano]

Thanks. That is exactly what I needed to fix mine :D Ah these old drills are a job to work with and work on

[@ivaerak]

In my case the 'bearing' is actually the mechanism with two little metal pins that locks the chuck when replacing the drill bit. It broke in four, hence the wobble and the chuck cannot lock anything - it spins in place. My drill is the keyless one.

[@stewartbruce8902]

Brilliant video tutorial Jhon. Thank you for your top shelf repair technique. All the best from New Rochelle N.Y.

[@AliAli-tp8fh]

Thank you alot

[@Lovelypaasam05]

Thanks for this video, I will try my wobbling chuck and share the result

[@mansigisigi]

thank you for your video. this is what i want~! i wlll be trying to follow this video to repair my drill.

[@albertocamilo1420]

Dont know if anyone gives a damn but if you are stoned like me atm you can stream pretty much all of the new movies on InstaFlixxer. Been watching with my gf for the last days xD

[@hectorkayden2424]

@Alberto Camilo yup, been watching on InstaFlixxer for years myself :)

[@aria1000]

i really thought i have the same problem but turnout it's the chuck was not tight enough but good video nevertheless 👍

[@jubalsscreen]

Paano namn yung ayaw sumabay yung tatlong nasa butas?

[@MadScientistGuitarLab]

That’s cool. Thanks!

[@gwynforddafydd1397]

Are you trying to light a fire with that drill bit ?

[@AS-tx2dr]

I had made a drill press with my drill and no matter what I did, I was not getting accurate holes. I was even contemplating buying another piece of the same model so that it would fit precisely on my drill press and I thought I would try to see if someone had fixed it and landed on your video. It has certainly reduced the side-to-side movement. Hopefully I will get accurate holes now. Thanks a lot!

[@truthfinder6999]

Had exactly same problem today ...searched for ideas and found this video. Hope to get a good result.

[@guvifiriel7117]

Bikin ptoject bend saw dong om.....

[@jhonarief]

siap nanti saya bikinkan kebetulan sudah ada bandsaw buatan rekan sendiri

[@guvifiriel7117]

@@jhonarief ok mantap aku tunggu vidionya om

[@jhonarief]

@@guvifiriel7117 siaap

[@EVERSIMPLESIMPLEEVERSIMPLESIMP]

Superb

[@Nekuct1337]

Good video

[@windowsxp2030]

hi sir , can i send you the picture of my drill? cause i dont realy know the problem it does turn on but the the chuck doesnt spin hope to fix it soon for my project..

[@jhonarief]

I think your drill have problem with the shaft that connected with the motor,

[@windowsxp2030]

@@jhonarief can it be fix sir?

[@jhonarief]

@@windowsxp2030 all problem can be fix, if you try to open the casing I'm sure you will find the problem. try to open it

[@windowsxp2030]

@@jhonarief Already open it, then saw this two gears doesnt line up correctly

[@jhonarief]

@@windowsxp2030 that is the problem, try to line it up and put it back together again and you will have working drill, you done a good job