This short video will show how to easily align and install the bolt catch roll pin on your AR lower. If this is something you do regularly, you should watch this.
Пікірлер: 409
@chrissewell16082 жыл бұрын
Instead of making the bent wire tool. You can use a small allen wrench, that fits, and gets held in place under spring tension. A roll pin starter punch & roll pin punch, made for the AR Lower, is a great tool set to get too.
@rickalexander2801 Жыл бұрын
Wheeler Engineering makes both the starter punch and roll pin punch set. They work well for me.
@henryhill61264 жыл бұрын
Hello Joe, you are a clever man. This looks like an inexpensive way to do a tricky job. Thanks for your generosity.
@flyguy302632 жыл бұрын
I've put together dozens of lowers and this is the easiest technique I've seen for the bolt catch pin. Thanks for sharing.
@joepie2212 жыл бұрын
Glad you liked it. It works well.
@markstripes8237 Жыл бұрын
First several I did with just a correctly sized roll pin punch. Even after reading the dire warnings about slipping off the pin and making a big ugly scratch in the side of the receiver. All of them came out unblemished. Your shop made tool is perfect and a fraction of the cost of the purpose built set of tools from Wheeler. As long as you have a lathe to drill the hole... Great tip on the welding rod bent retaining/ lineup tool. As always well done Joe! Thank you.
@joepie221 Жыл бұрын
The long punch is really safe and effective. Thanks for the comment.
@codygreene9067 Жыл бұрын
If you’re worried about your guns getting scratched up you must not shoot them very often 😂
@markstripes8237 Жыл бұрын
Thanks for pointing out your complete lack of understanding of good workmanship and fine craftsmanship. @@codygreene9067
@dougcormack8240 Жыл бұрын
I like this idea using a long punch to reach it and the hole in the end is nice. One thing you might do is add some heat shrink to the rod to prevent some nicks in case of a slip.
@danielburke83505 жыл бұрын
I'd been futzing around with this all afternoon trying to figure out how to grow a third hand. I love the pin-holding punch idea. Simple and effective. I found a piece of 3/16" HRS in my scrap bin and drilled it in my lathe; works PERFECTLY. One of those "why didn't I think of that?" moments. Thanks for sharing your ideas.
@Pandrnchicken3 жыл бұрын
Could use a small cleaning rod, worked for me
@kzebski4 жыл бұрын
What a great video. Well-lit and visible closeups, quick explanations, and no wasted time on setups. Thank you.
@joepie2214 жыл бұрын
Glad you enjoyed it! Did you see the machining series that made this lower?
@noobsmoke79 Жыл бұрын
A piece of toothpick makes a pretty good slave pin as well (but I actually like the weld rod better). I like that 1/4” homemade punch better than the slab sided punches that are made for this. I’ve actually bent a couple of them and the slab side still touches the receiver - so you still need tape. Yours is the best method I’ve seen yet. Now I want to get another lower just so I can try it out 😊.
@thetoecutter135 жыл бұрын
I'm a little proud of myself, I did the same thing when I built my first lower. I used an allen key instead of a bending a welding rod. When I was an auto mechanic I learned to start bigger roll pins by holding them in a deep socket and tapping them in with an extension. Subaru half shafts are held in with roll pins and can be easily reinstalled with that trick. I didn't invent that though, I was shown it when I was an apprentice.
@joepie2215 жыл бұрын
Its a solid technique and can save damage to the receiving part.
@thetoecutter135 жыл бұрын
MASON CROSS I would have moved across the country to be his apprentice, I learn something with every one of his videos. And he's doing something right, look at his shop. Keep it up Joe. Please. You have a lot to offer and the vast majority of us watching want to learn from you.
@criagcundiff24692 жыл бұрын
OMG! Thank you! I am attempting my first ever build. and Boy, You have made a difficult operation super-simple. Getting the right tips from guys that really know what they are doing makes all the difference in the world. I sure wish I had seen this before I tried it the first time, LOL!
@Jason-iz6ob3 жыл бұрын
Good video. I was looking for slightly more instant gratification than a trip to the welding shop. So I just used a 2mm Allen wrench to hold everything together while I drove the pin in. Worked great.
@sloweg31133 жыл бұрын
I used an old wire coat hanger
@moparbryan Жыл бұрын
You can also use a 3/32 Allen wrench if it’s too long just wittle it down on or with a grinder. If you don’t know any welders.
@keltecfan2 жыл бұрын
Excellent & informative video Joe, thank you. If you don't have access to 093 or 3/32" filler rod, a (2D zinc coated?) finishing nail with the point ground off & bent will do the trick too.
@joepie2212 жыл бұрын
Great tip!
@kevpachakey11 ай бұрын
It also fits perfectly in a T30 security star drive. Thanks for the idea! Worked great
@tcarr13 жыл бұрын
Just found this and THANK. YOU. Where on this forsaken green earth was THIS tidbit when I built one AR and upgraded, and worked on my other? THIS is an epically simple solution to end a lot of non-child approved verbiage. Stellar, man. Thank you!!
@BrewCityRider2 жыл бұрын
Real Avid makes a two punch kit made specifically for this job, which I like, and its only 13 bucks or so. The punches have notched out sides to fit the receiver better, and the starter punch is magnetic to easily hold the roll pin.
@wk7783 Жыл бұрын
Best install and instruction I have seen !
@bobkeller83834 жыл бұрын
I just trashed my pin trying to install. And its 10:34 at night. Now I have to go to work tonight and open up to get a new one! Thanks this helps except I dont have the tools to do it like you have. My next purchase is a pin starter and punch set.
@jiujitsuforall86274 жыл бұрын
Dude, simple, fast, and effective AND hardly any additional cost for job-specific tools!!! Thanks!!! I struggled mightily getting that bolt catch in-even had to have my son help me! Needed four hands to complete the job. It's one of those,"why didn't I think of that?!?!?" situations. Again, thanks for posting this vid!
@Whizzo3337 ай бұрын
The best part is the magwell vise block machined from oak.......🇺🇸✊
@joepie2217 ай бұрын
Guaranteed not to scratch the finish.
@Tigris_River_Sand_Fleas8 күн бұрын
@@joepie221 you might want to consider purchasing a 3D printer if you don't have one already. You can print so many crafty things for the house and shop and more. I have printed cabinets, tables, tools, spatulas, tiles for the kitchen floor, pegboard, hangers, picture frames, soap holder, salt and pepper shaker and the list go on for days. What might interest you some more is related to firearms. I have printed hundreds of firearm parts from buttstocks to sights to P80 (Glock) lowers. Obviously, it's good to know how to make springs etc. vs spending hundreds of dollars on Glock parts. Most of my printing is actually AR related. Check out the CAD files available online. It's crazy how popular it has become. There are even states trying (if they haven't yet) to ban 3D printers because people are building complete firearm chassis with them.
@unioncreek6 жыл бұрын
Joe, thanks for the tips. I've put together a few lowers and your tip is one that saves the most time and lowers the chance on marking up a lower.
@tomthumb20575 жыл бұрын
Nice video:) One other way is to use a pair of channel locks with one face covered in electrical tape. You just do a simple tap and then you the channel locks to squeeze the pin into place. Has worked for me for over 20 years...
@joepie2215 жыл бұрын
I've seen that done, but if you think about it, the small protrusion with the far pin receiver hole is taking all the stress from the channel lock pressure. The possibility of it snapping off is very high. The wall thickness on that feature on either side of the pin hole is very thin and could crack easily.
@anthonylapatka15086 жыл бұрын
Joe how did you know I was building another AR and was looking for a better way to install this roll pin? Your psychic! The slave pin is a great idea. This was a great short project for me this afternoon. I'm just learning how to make chips and break tools on a lathe and a mill. Please keep the excellent videos coming. Thanks!
@joepie2216 жыл бұрын
Hit that sub button after you stop smiling.
@julianp.17136 жыл бұрын
You can buy a roll pin install punch in several sizes that does the same thing. Great to have in your repair kit. Seat it with a roll pin driving punch that has a nipple the size of the hole in the roll pin, in several sizes. Common in armorer kits.
@jamesferguson23539 ай бұрын
I've been using KNS's precision bolt catch retaining pin , I have been quite happy with it so far.
@armenenkel3547 Жыл бұрын
I like this way of doing it. Absolutely safer for the lower.
@joepie221 Жыл бұрын
The small lugs that hold the bolt catch/release lever are extremely small. Squeezing that pin in has always made me cringe regardless of who did it. You snap one of those little lugs off and kiss the lower good bye. The extended female punch is a good approach.
@lp11335 жыл бұрын
Excellent idea. Love that suggestion of 3/32 filler rod. Going to buy some at Lowe's right now. Thank you!!
@milesmanges Жыл бұрын
Thank you, followed your instructions and used a small allen wrench as a slave pin, one thing i did differently was tap the roll pin in slightly just to get it started because i didnt have a vice, this was my first build and it turned out great
@TactlessWookie6 жыл бұрын
That is very similar how I install those pins. However I use a roll pin starter punch and then a standard roll pin punch. Not a custom tool. I also place masking tape on the side of the lower to eliminate "oops" marks in the finish. This has worked well for the dozen or so rifles I've built. I love the slave pin idea. I'll be making a slave for use in my next build. Thanks Joe!
@sinkhole406 жыл бұрын
Joe, one other thing that I do is install a piece of shrink wrap over the ¼" drive rod. This will eliminate any scuff marks on the side of the receiver.
@davidmarberry55656 жыл бұрын
now yur thinkin, excellent idea
@usatrooper504510 ай бұрын
Aero lowers nowadays eliminates all that with a threaded pin and a few other great features but that is a very good tip 👍🤪🇺🇲
@joepie22110 ай бұрын
I cringe when I see someone squeeze those little ears with taped pliers. Break one off and you throw that lower in the trash.
@MR619Can10 ай бұрын
on std milspec lowers, you can insert from front using Brownells and others 1/2 milled punches. use appropriate sized punch from rear to act as slave pin. Bias the 1/2 milled punch slightly away from the receiver while you get the roll pin started and then straighten the punch to knock it the rest of the way in. Additionally, to assist holding the bolt catch in place, you can get the hammer to go into the forward position and it will apply pressure to bolt catch while you knock the roll pin in. using the hammer technique also helps when you are removing the bolt catch assembly for replacement and to prevent the catch/plunger and spring from taking off if you forget to hold the catch in place when you remove the 1/2 milled punch.
@jeffreywall48182 жыл бұрын
A couple of good tips here. i would add: 1 - A drop of good lubricant or even white lithium grease on the spring and plunger will help ensure free flowng action of the bolt lock 2 - Ensure there is a good taper on the insertion end of the roll pin [my experience is that 50% are not well tapered]. A minute of so with a sharp mill bastard file will do the trick 3 - Before you drive in the roll pin ,put a drop of oil on that as well. It greatly eases the installation of the roll pin 4 - It makes good sense to put at least 2 layers of painter's tape on the lower receiver before you go to hammering away on your roll pin starter punch and later when you are finish driving. For whatever reason it is easy to mar the finish of the lower when installing this pin. 5 - While you can cover up accidental mars with a Sharpie, a better option is to buy a bottle of Aluminium Black from Brownells. The Sharpie leaves a shiny repair that doesna match the finish. The Aluminium Black matches perfectly - unless of course your receiver is blue or red or chartruse or you are going to hit it with Krylon camo paint and then who cares?
@joepie2212 жыл бұрын
I am a former surgical instrument designer. Instruments need to be thoroughly cleaned between cases so we added access holes and slots. Hot water and detergents don't always get where it needs to get without access features on the instrument. On the OTHER hand, debris doesn't get there either, so its a balance of whats really needed. Now to the point....Roll pins are hardened and unlikely to transfer with use, and the bolt catch lever is usually hardened as well. This being said, these surfaces should function well as is, better with lube of course, but the lube now acts as an attraction point for dirt and sediment that will accelerate wear over time. If its a range gun, oil it, if its a jungle gun, I personally would just keep it clean and oil only the important stuff. Just my opinion. Initial lube at installation is a good idea, but keep your chamfer small because the resting land isn't very big and you want as much contact as possible.
@mikedifeo83446 жыл бұрын
Great Vid. I built one and it sure saves a lot of time and headaches. Thanks for sharing.
@joepie2216 жыл бұрын
It works very well. The slave pin is a must.
@chief12235 жыл бұрын
However you get the pin in or out, masking tape can be used to help prevent scuffing. Saw that trick in Midway's howto series.
@nunyabinness3574 Жыл бұрын
Ive pushed in quite a few catch pibs with the taped channel locks method...never had any problems 👍🏾
@joepie221 Жыл бұрын
Yet.
@southtoledobendla6 жыл бұрын
Great tip Joe. So many people do this wrong glad you made it so simple. I will be sharing it...
@joepie2216 жыл бұрын
Thanks. I don't believe in struggling if I don't have to.
@Oldjun3 жыл бұрын
I've tried every trick in the book for removing/installing the bolt catch roll pin. These are the two tools that have worked best for me: Brownell's Bolt Catch Pin Punch (Part# 080-216-012WB) - A slab-sided punch that clears the left side of the magwell, allowing you to drive out the punch without marring your lower. In addition, I put a piece of masking tape over the "hump" on the magwell for added protection. KAK Walt's Tool - A long, roll pin punch starter, similar to the one you made. First, I insert the bolt catch and use the Brownell's punch to line it up with the corresponding holes in the lower. Then I start off the roll pin with the KAK punch and then drive it in about 90% of the way with a regular solid punch (instead of a roll pin punch). This is to prevent the end of the roll pin from "mushrooming" if there is too much resistance. Then I finish it off with a 3/32" roll pin punch. Done.
@joepie2213 жыл бұрын
The one big mistake people make with a roll pin is using a punch that has a conical tip. Under pressure, it expands the pin and makes it harder to install. A flat face, or hollow punch like the one here is much better.
@AlexanderEddy4 жыл бұрын
Nifty trick! I was saved the hassle of using a roll pin for the bolt catch on my Stag 10, because Stag cleverly replaced that piece with a pin that's threaded on the end, but I'll need to install a bolt catch roll pin soon. I'll give this a try.
@zschannel49583 жыл бұрын
Thanks, Joe. Very well done and so simple.
@brianneedham60604 жыл бұрын
Absolutely the best video on KZbin on the topic
@joepie2214 жыл бұрын
Did you see the series on the production of that lower?
@brianneedham60604 жыл бұрын
@@joepie221 no but I will go back and check it out! I love finding new channels and ways of doing things!
I only purchase uppers (correction ‘lower’) that have a grove running across that extended section. If a manufacturer doesn’t take this extra step- he doesn’t earn my money.. Best video on this instillation. Thanks All Black Rifles Matter
@joepie2215 жыл бұрын
You said upper?
@noretreat20745 жыл бұрын
My bad
@EndTheFed1933 Жыл бұрын
Man this just helped me out so much!
@coachwill2 жыл бұрын
You can also use the short end of a 1/15" allen wrench from the front end if you don't have time or the place to go get wire to use. I also just a gentle tap from a brass hammer to start the pin and then used a 5/32" (4mm) tapered Irwin punch to finish the pin insert with the allen wrench getting pushed out of the front end.
@joepie2212 жыл бұрын
Sounds like a good method, but my subscribers would hang me if I didn't ask about the 1/15" allen wrench. 1/16" maybe ??
@4000FeetHigh3 жыл бұрын
You sir, are a genius. This is awesome. I now have two tools which cost me around $3.
@joepie2213 жыл бұрын
Glad I could help
@chrissewell16084 жыл бұрын
That 3/32" slave pin, wire is a great idea. Good job on the homemade punch & pin starter too.
@joepie2214 жыл бұрын
After machining that lower from a solid block, the punch and pin starter were a piece of cake. Thanks for the comment.
@bobchester15686 жыл бұрын
I have got into the habit of tapping the hole and using a 3/8" long grub screw. Makes it easier if I want to change the bolt catch to something different later on. Good tip though, Joe. I struggled with the first couple ARs I built because of that stupid roll pin.
@KingOfTheLosers135 жыл бұрын
Grace sells a pin punch that is specifically for the bolt catch. It has a notched side so it doesn't mar the receiver while driving the pin . However it's nice to see some people still have ingenuity great video Joe.
@joepie2215 жыл бұрын
Beware the pin punch that goes inside the pin. Some of these have a radius where the small and large diameters come together. Under pressure, the radius will expand the pin and make it harder to drive in. A hollow driver like the one shown here is better for split roll pin installation.
@KingOfTheLosers135 жыл бұрын
@@joepie221 I was talking about the hole in the end punch. I have and use both though and I agree if you don't have the proper fit it can create problems. That aside I have respect for the fact that you had the ingenuity & took the time to fabricate your own punch. You do solid work thanks for sharing Joe.
@joepie2215 жыл бұрын
@@KingOfTheLosers13 Did you get an opportunity to watch the fabrication series on that lower before it came down?
@KingOfTheLosers135 жыл бұрын
@@joepie221 no I didn't I was looking for it but couldn't find it.
Looks like you nicked the finish. Your homemade roll pin starter looks great but use a proper roll pin punch to finish. It will allow you to recess the pin just a bit without damaging your upper.
@MrGyrhed3 жыл бұрын
OMG start the roll pin fist from the rear to where it just protrudes into the gap, put all the other parts in, squeeze the roll pin into place with a pair of channel locks with a little electrical tape wrapped arround them. I had no idea people thought this was hard to do until I was looking arround on u-tube and found out how many people make this harder that it needs to be. Once you start to squeeze the channel plocks you can wiggle arround the stop to get it lined up with the free hand. I didnt even use a vise to hold the reciever when i was younger, arthritis made me a littlle less sure handed.
@joepie2213 жыл бұрын
I would never tell anyone to squeeze those tabs with vise grips, wrapped in tape or not. Its a common practice, but that small piece of aluminum shouldn't be squeezed with anything.
@MrGyrhed3 жыл бұрын
@@joepie221 if you will note i said channel locks, not vice grips. Big difference. If you cant judge the pressure you are putting on a roll pin for crying out loud then yes don't use this method. But is reality there is far less chance of damaging it with the easy pressure of channel locks that a drift and a hammer. Come on!! Lets beat on it rather than gently push. The parts fill the gap as well and you have already started the pin in the near side hole. I think maybe someone just want to be an internet expert.
@Shop-Tech5 жыл бұрын
Store bought ones go inside the pin and can expand the diameter under drive in pressure. OD nesting is the way to go.
@PyroShim6 жыл бұрын
The wire tip was great! I would turn a feature on second side of the punch that has a first diameter that fits into the center hole of the pin and then the second diameter is only slightly thicker than the wall thickness of the pin. That way you will never catch on the receiver itself. A correct diameter hole transfer punch should do fine also.
@LoanwordEggcorn6 жыл бұрын
A flat step on the punch as you first mentioned would be better than a transfer punch or tapered pin because it would expand the roll pin less, by driving on the end of the pin, and not from the inside diameter of the pin. You want to push straight on end of the pin and not from the inner diameter of the pin, which would do work to expand it.
@hhimynameischris3 жыл бұрын
if you shut the hammer on the trigger it generally will hold the bolt catch in place without needing something to hold it. ive also built an AR lower entirely with a vice. not even using a hammer get creative chat its just pounding a pin in a hole you dont need any fancy tools like some other people commenting were talking about not having.
@darthcollosus6 жыл бұрын
Slick I like that trick! I will say I've used the vise grip method a number of times and it's worked for me and hasn't damaged the lower at all but I suppose it's possible
@EmmaRitson6 жыл бұрын
ok. i rarely watch gun vids. this tip will directly translate to a watch pin issue ive been having though, and i thank you for that!
@joepie2216 жыл бұрын
Excellent. The slave pin technique really helps to align things you can't see. I use it in many applications. This is just one. Thanks for the comment.
@someinternetdude41594 жыл бұрын
I don't know if some companies make AR-15 lowers with a threaded hole and threaded pin or not. I haven't looked into it. However, on my AERO Precision AR-10 (308) lower it is threaded with a Torx head and it makes it very easy to install.
@joepie2214 жыл бұрын
I believe they do. I like the idea. Since I made this lower, I should have considered that upgrade.
@englishxdave4 жыл бұрын
Aero M4E1 is threaded... along with the rear takedown to stop the spring from flying when replacing the stock
@PracticalAccuracy2 жыл бұрын
Brilliant. Was having problems lining up the hole and roll pin. I'll use your slave pin idea next time.
@MrScy13 Жыл бұрын
Easy installation. Just need to make custom fab tools for something many people will only do once. Instead of getting wire from a "local welder" and bending it, why not use a small Allen key? Lubricate the holes, get the roll pin stated, then slowly and carefully squeezed it in with some vice grips.
@joepie221 Жыл бұрын
I'm sure there are many ways to do this. You choose the one that makes you happy. Me...I'll never use taped up vise grips to install a bolt catch pin. You snap one of those ears off and the lower is trash.
@amishplumber9850 Жыл бұрын
Similar to how I do it. I put masking tape on my lower just in case I slip. Nice work
@joepie221 Жыл бұрын
Thanks.
@yuduul71778 ай бұрын
I've messed up TWO lowers installing this POS! Probably THE MOST frustrating part to install!!!
@hepkerfamily95848 ай бұрын
AeroPrecision makes a M4E1 lower that actually makes this a threaded rod rather than a punchable pin. They improved this unlike everyone else. It is however a little more money. Just an FYI. I damaged multiple before seeing these
@Neonrt131 Жыл бұрын
just wanted to thank you for the helpful video, btw i found that a 5/64 allen key does the trick of your wire you used to keep hole aligned, i rigged a driver per your instructions and viola she is in man!
@joepie221 Жыл бұрын
Glad it helped
@jamesvatter57292 жыл бұрын
Slick trick! Thanks for sharing.
@joepie2212 жыл бұрын
Glad you liked it!
@ReelTimeCapt2 жыл бұрын
A 5/64 allen key works a slave pin too. Great video and thank u!
@johnlumpkin30824 жыл бұрын
I have a roll pin starter punch for that, the piece of wire from the front is a must unless you have three hands. Yeah, you have to install the mag release first, thanks for the reminder.
@joepie2214 жыл бұрын
Unless its a hollow punch like the one shown, a flat face punch is the next best thing. Don't use a pin punch with a pointed tip it expands the roll pin when it meets resistance and makes it even harder to drive in.
@lesterknipe80828 ай бұрын
While you’re making punches make a roll pin punch and grind about 4.5” of the side of the punch then with a little tape on the receiver you won’t scratch the side of the receiver. As a gunsmith if I scratched the side of the reciever as you did some customers will complain.
@joepie2218 ай бұрын
I made the receiver from a solid block of aluminum. I can probably make that scratch disappear.
@zachpyron11996 жыл бұрын
Pretty much exactly how we do it in the shop. We made a starter punch and then found an extra length roll pin punch, with the little centering nub on the end. That guy almost guarantees not to damage the receiver as it is the same diameter as the pin. Then just a dab of super black to color the pin.
@OpaKnows2 жыл бұрын
I just use a broken off piece of wooden q-tip. It’s also the perfect size, and it is slightly flexible.
@joepie2212 жыл бұрын
Good thought.
@roostershooter764 жыл бұрын
Brownells makes an Offset Roll Pin punch that allows you to install it from the rear. You won't mark up your receiver, as displayed on the rear of the bolt catch here.
@joepie2214 жыл бұрын
A lot of people don't realize if you drive a roll pin from the inside, it expands it and makes it harder to seat. Roll pins should be installed either dead ended or in a cup. Its easier.
@tenhundredkills2 жыл бұрын
Or, you could just get a proper roll pin punch set. They're not expensive and they're made specifically for roll pins. As for a slave pin, a small allen wrench works A-OK and is pretty easy to find if you don't already have one. It's easier than finding a local welder for a filler rod and drilling your own hole into a blank piece of steel rod!
@joepie2212 жыл бұрын
For sure you have many options. This is mine.
@ar-15techtipsinunder5minut89 ай бұрын
DONE= scratched!
@drickard676 жыл бұрын
Good tip! I have\use roll pin starter punches and roll pin punches like is mentioned by an earlier comment. I also have one designed specifically for the AR that is milled flat on one side...
@joepie2216 жыл бұрын
Punches with conical tip leads that go inside the pin will locate them just fine, but under impact, that same conical feature will spread the pin and add to resistance. Roll pins should not be driven from the ID.
@drickard676 жыл бұрын
Joe Pieczynski good point... Though mine have just a slight some that only serves to center the punch on the pin and the outside diameter is what drives the punch. They are truly better used and invaluable in removing the roll pin. My method is similar to yours...start it with a roll pin starter punch and finishing with the biggest flat punch. I've picked up tons of good tips and methods from you... Thanks for sharing your experience!
@sidneycook31962 жыл бұрын
Thank you sir I was at this point and I wasn't sure what to do big thumbs 👍 up
@joepie2212 жыл бұрын
Thanks. Be gentle to those little blocks.
@robertgolden10804 жыл бұрын
Awesome video man. Quick, to the point and very informative.
@joepie2214 жыл бұрын
Glad you liked it. Did you catch the series showing the machining of that lower from a solid block?
@robertgolden10804 жыл бұрын
Joe Pieczynski Not yet but I will, thanks.
@joepie2214 жыл бұрын
@@robertgolden1080 The series is on another platform. www.firearmstalk.com/threads/ar-lower-done-by-a-true-machinist.124416/
@Anonymous83174 жыл бұрын
FYI, you can use a roll pin starter punch vs drilling your own to drive it through. His tool is easier to use though if you have the tools/patience. The wire is a good tip.
@tizwicky6 жыл бұрын
Thank You, you are very skilled! I learned alot from your approach.
@PriklyPete3 жыл бұрын
Excellent video for a bolt catch installation.....................Thank you
@kamikaze2532 жыл бұрын
I've never seen anyone install the roll pin from the front. Never have I had any trouble installing the roll pins either.
@joepie2212 жыл бұрын
I have.
@worthdoss80436 жыл бұрын
Great job Joe, now your are ready to install a new hammer spring on a Thompson Contender.;>)
@edwardberwind85442 жыл бұрын
Joe, Well done very clever. I'll be making my own tools.
@MrWeliz2 жыл бұрын
I used a pice of wire coat hanger that i found in my closet, i cut it and bent it with pliers , the wire coat hangers come in one or two different thicknesses .
@williamkeiser84162 жыл бұрын
Absolutely genius! Thank you for this video
@zaldumbide135 жыл бұрын
Very nice, thank you for sharing with the KZbin community.
@joepie2215 жыл бұрын
You may enjoy the 10 part series on my Google Plus page.
@ChrisB2576 жыл бұрын
Totally inspired Joe and logical too. Hope I don't have to bother but like Chuck, wondering the best way to drift that pin out again, safely - if in fact that would necessary.
@davidmarberry55656 жыл бұрын
wow, why didn't i think of that. i must be getting old. great job , thanks!
@Odessa452 жыл бұрын
Nice video. Double check for a taper on the end of the roll pin before starting. Lube everything first Make the starter rod/tool out of brass ;)
@joepie2212 жыл бұрын
Just as a caution, brass will still nick aluminum. I was pissed when I hit the edge. I made that lower from a solid billet and it was flawless.
@Odessa452 жыл бұрын
@@joepie221 Well, at least it was you that did the deed. It really sucks when you hand something off to a "buddy" and later they hand it back kanked......
@jamesstacey5292 жыл бұрын
Yep the taper on the roll pin that's what got me😏
@FalconLair093 жыл бұрын
you're a problem solver Joe - good for you
@thomasdaum19273 жыл бұрын
Good job , you can also use this technique on the gas block gas tube install ! Thanks
@controlledburst3 жыл бұрын
Didn't know Jim Belushi was an AR enthusiast!
@joepie2213 жыл бұрын
You should see how that lower was machined from a solid block.
@juansala53162 жыл бұрын
Thank You for this!!! Tomorrow i'll get these tools
@quiettime68715 жыл бұрын
I always forget to put the mag catch in first! But, push the button and grab the back side and pull it out as far as you can against the spring and it will clear the standard bolt release
@102232206 жыл бұрын
So simple but so affective I like it 👍 thanks
@sttvoyager17276 жыл бұрын
That was FANTASTIC!!! Thank you!! Subscribed!!!
@joepie2216 жыл бұрын
You may also enjoy some of the related content found here. Thanks for the sub. plus.google.com/101634339622119637681
@Pandrnchicken3 жыл бұрын
Thanks for this pops! That was a quick job…
@joepie2213 жыл бұрын
The slave pin works well.
@pjtange4 жыл бұрын
Well done, just the tip I was looking for.
@joepie2214 жыл бұрын
I made that lower from a solid block of aluminum. Did you see the series before it came down?
@jessarellanes6648 Жыл бұрын
Thank you.
@joepie221 Жыл бұрын
You bet.
@skeeter500016 жыл бұрын
Nice/great tip Joe, I don't own an AR15..........Yet
@dano49283 жыл бұрын
On another post someone suggested freezing the pin to aid in installation.
@billmurphy86853 жыл бұрын
Get video looks pretty straight forward. I was having trouble not having a 3rd hand when trying to do it
@joepie2213 жыл бұрын
Another viewer said a round toothpick is another option to hold it.
@the.greyman.74804 жыл бұрын
Perfect. However, lubricate before install.
@bizoyd296 жыл бұрын
you should make and sell these tools. I would buy them right now.!!
@grntitan16 жыл бұрын
I have a whole set of roll pin punches like these for all the standard size roll pins. I don't recall where I purchased them, but they are USA made and a great addition to the machinist tool arsenal.
@chief12235 жыл бұрын
Yeah, a roll pin starter set and an allen wrench set is basically the same thing used here, although the roll pin punches might be a bit shorter and have a hard time clearing the back of the receiver. If you really want something specialized there is the Wheeler 710906. The idea here is that short of spending $15+ on specialty tools you could grab what you need today at any hardware store. The specialty tools already exist if that's what you want. I've done lowers with just a standard roll pin set and a roll pin starter set, but the Wheeler tool for the mag catch is the only thing I might add at some point, unless I feel like making a generic insulated punch extension that won't mar the housing when slipped over the punches to do the bolt catch.