Easy-Laser E540 (& E420) Training - Horizontal Shaft Alignment

[@Bellaterner]

Great video guys! You are really showing us how easy shaftalignment can be using the right tool!

[@nicrendon8703]

Great video, but I would have like to seen the unit be bolted down and see if any changes taken place and were needed due to soft foot and what the process is for corrections

[@BENCHMARKPDM]

Hi Nic, we spend some time on Softfoot and other Measurement Options the E420/E540 has in Part 2 of this video. Check it out at around the 6:00 minute mark here: kzbin.info/www/bejne/iIGrf6V5qNuehZo - please let us know if you have any other comments. We appreciate the feedback!

[@EngDynamicsSA]

It is so "easy" to use compared to other systems out there!

[@MrJorgepiscis]

+Christo van der Walt : The price is more better!

[@ignaciosergio5878]

you prolly dont care but does anybody know a tool to get back into an instagram account?? I somehow forgot the password. I love any tricks you can give me

[@leightonmarcellus9897]

@Ignacio Sergio Instablaster :)

[@siyadabdulsamad]

I am using this mechine since from 7 years

[@HaniAyop]

Please, can you send me the report of this work؟

[@kareemmostafa5145]

Great Video. Thanks for your efforts

[@raymondtsh7276]

At 4:49 you said you're happy because it's under 20 thousandth? But after angular adjustment, one of the values are more than 20 thousandth, why continue with the alignment ?

[@BENCHMARKPDM]

Getting it under 20 thou is just a basic rule of thumb for setting the beams up but anywhere near 20 thou would be fine. All we are doing here is getting the lasers close to the center of each detector surface. The reason for this is so it can stay in each other detectors surface when you rotate the shaft 180 degrees. As soon as you take your first measurement it creates the references going to zero and measures from that first position. If there was a lot of misalignment, at a long distance out in the field, there is a chance the laser can come out of the detector surface if you don't get the lasers in the midst of the detector range (ie. the center). However, at this small distance, it wouldn't matter. It is good practice to get it close to zero if you can.

[@raymondtsh7276]

@@BENCHMARKPDM thanks for the info sir. This info wasn't found in the E-420 manual and hence my question. Thanks again ;)

[@prince__kumar6129]

How much sim we add under the foot.according to the reading or half of the reading?

[@hiwaabdulhaq3465]

So thanks , it was a clear and informative

[@saichaithanyajoolakanti928]

Can the same procedure could be done without coupling??

[@BENCHMARKPDM]

Hello Sai - yes! You can do an open-coupling alignment using the built-in inclinometers. See this video for the instruction on how to do this: kzbin.info/www/bejne/iIGrf6V5qNuehZo

[@dabbangnihal3284]

Very very thanks you sir😊

[@jamesmcintyre-i6g]

Very clear

[@sakipambura9966]

How much is this machine

[@jameschasteen9641]

Wut if shaft different diameters

[@arfaahmad8751]

I am using that machine in KSA funtastic and very very easy .

[@raymondtsh7276]

Sir, how you measure the 4 inches?

[@BENCHMARKPDM]

The 4 inches is the S-C distance, Stationary unit to center of coupling. The S-M distance is automatically halved to give the the S-C but you can override this if the center of the coupling distance is different.

[@raymondtsh7276]

@@BENCHMARKPDM thanks for the info sir ;)

[@HareKrishnaHareRamTLSR]

Nice sir you help us, thank you.

[@jameschasteen9641]

No coubling

[@giltupaz5979]

complicated.better traditional rim n face method n finish with simple triangulation.

[@ОдинокийКурильщик-ж2д]

Нихт, нихт , не хочу ! Много лишних движений , при выполнении всего то одной фунции .

[@BENCHMARKPDM]

This video is meant to show a lot of the different features available, not how it would necessarily be done out in the field.

[@AndersonSilva-rf1th]

queria uma manual em português

[@BENCHMARKPDM]

easylaser.com/en-us/support/manuals

[@herbertXX]

outdated

[@BENCHMARKPDM]

Hi Herbert74, thanks for your feedback! While the E540 is technically obsolete/discontinued, the E420 is still going strong as the software applies to both alignment tools. The video is also over 5 years old and still providing good training for our E420/E540 users! If you are looking for something newer, check out our newer EASY-LASER XT alignment tools in this video shaft alignment demonstration kzbin.info/www/bejne/mHaUgKmnlLxpgK8.