Thank you Teo, Enjoying this build Series..screw-ups and all!!! Lots of good tips…like for the jigsaw at 20:30. Cheers Livio
@TheBoatRambler5 ай бұрын
Thanks Livio!
@marcus_k855 ай бұрын
Great work again!! Looking forward seeing you on the water in April 😊
@TheBoatRambler5 ай бұрын
Thanks Marcus!
@damoog59855 ай бұрын
I used cheap router bits and ruined a piece when the bearing failed and fell off. Great videos, thanks for sharing.
@liamstone34375 ай бұрын
You have a router now. You should make a scarf sled and make your scarfs that way from now on.
@TheBoatRambler5 ай бұрын
I don't think I will be making many scarfs after this boat is finished but it's always something for me to build if I get bored! 😁
@colrodrick87845 ай бұрын
@@TheBoatRamblerI’d build one of those iff I were making lots of scarphs too. Instead I grab the belt sander or for a work out a rasp and then sandpaper. There’s a sled design on line from Jim Mikalak (Jim’s Boats).
@finianmcelhany39045 ай бұрын
I love every video, watch them as soon as I see them. Been watching for years
@TheBoatRambler5 ай бұрын
Thank you very much for your support! 😉
@erikhedl20845 ай бұрын
We can't wait to see you launch! You are quite the craftsman.
@TheBoatRambler5 ай бұрын
Thanks for watching!
@setkacagarro-blogspot-com5 ай бұрын
Hey Teo, Great! Its id nice that you got "sponsored /supported" by RSS and Michael Storer and his wife , you deserve it for great video and being so humble and real
@TheBoatRambler5 ай бұрын
Thanks Nathan! 😁
@michaelbell74655 ай бұрын
To speed up the scarfing process, mark the wood and cut the majority with a jig saw. Then set up for plane.
@TheBoatRambler5 ай бұрын
Thanks for the tip. On smaller scarfs I actually cut them with a tenon saw and just finish with sandpaper. 😉
@geneberry71145 ай бұрын
RSS really are nice sails, I have the GIS sail on my Welsford Saturday Night Special, and a friend has the same sail on his Michalak Mayfly 16.
@KellyGerald-z9q5 ай бұрын
I’ve really enjoyed watching you build this boat and your other videos. If I’m not mistaken, you debated using a dagger board or a center board on the boat. Personally, I like that center boards fold neatly into the box instead of having to pull the dagger board up and worrying about hitting the boom. My experience is very limited and I’m sure you had a good reason for going the way you did. I’ve found a number of videos showing how to build a center board, the box, and how to install it but none I’ve seen have shown how to rig one. Even though you chose the dagger board, would it be possible for you to make a video, or use a few minutes in one of your videos, showing the basics of rigging a center board in case one of us wanted to use one? Just a basic overview would be very helpful and I could probably figure out the details on my own. I’m asking this of you instead of someone from the videos I’ve seen making them because you are very good at explaining the what you’re doing and why. I’m looking forward to the next video and can’t wait to see this amazing, funky looking boat in the water! Thanks for sharing this experience with us.
@TheBoatRambler5 ай бұрын
Hi, a swing centerboard was never an option for this build. -it would take up a lot more space on the cockpit making it harder to sleep aboard -It would need a complete different structure to support it -it would take more time to make -It would unbalance the boat if not fully deployed The dagger board has many advantages here. -very small center case -easy to build -you can sail with it at any depth and the boat's balance (CoE/CLR) will always stay the same, This is also valid for the cassette ruder comparing to a kick up rudder. I can not show you how to build a swing board as I have never built one. Cheers, Teo
@KellyGerald-z9q5 ай бұрын
@@TheBoatRambler thanks for clarifying this for me. I guess I saw the question of dagger board vs center board in a completely different boat build video. It’s not surprising that I got confused after watching so many back to back videos in a very short amount of time. That’s what happens when I get obsessed. Thanks for taking the time to reply. I’ll be looking forward to more of your great videos
@liamstone34375 ай бұрын
I hope you will show a list of tack (blocks, cleats, lines etc.) that you use with sizes and brand. That would be helpful. Thanks.
@TheBoatRambler5 ай бұрын
Hi Liam, I will detail all the rigging bits I'll use to rig it my way but you can already find a list on the OZ Goose website, down to the spec of the yard and all other lines.
@BensWorkshop5 ай бұрын
Good work. Looking forward to seeing it in the water.
@TheBoatRambler5 ай бұрын
Coming soon Ben! 😁
@MikStorer5 ай бұрын
Welcome about the sail Teo. Really appreciate the videos you are making. I guess you have a little commercial interest with Really Simple Sails now even though it was our surprise! But I know you will do your own thing in your own way :)
@TheBoatRambler5 ай бұрын
Thanks again Michael! I will give that sail good use! 😁😁
@shantoochristopher11535 ай бұрын
Hi, instead of a retractable dagger board...why not to make the sides of the boat little longer to make kind of huge fins, both sides?
@TheBoatRambler5 ай бұрын
Hi, that would be a question for the designer but I can think of a few reasons... the sides are made of 4mm plywood which would break too easy, the long fins would not have any hydrodynamic shape, there would be more wetted surface causing unnecessary drag, and I bet a few more good reasons too.
@ThaJay5 ай бұрын
In theory you can just increase the diameter of the hollow boom to make it much stronger. The core contributes almost nothing to the strength.
@TheBoatRambler5 ай бұрын
And that is exactly what I'm doing right now! 😉
@pontuswendt24865 ай бұрын
Would it be possible to build it out of pine or other cheap wood instead of marineplywood? Since I feel marineplywood is a liitle to expensive. Have plans to build a few for the sailingschool. Great videos love watching this series and others of you!!! Love the pedagogical aspects!
@TheBoatRambler5 ай бұрын
Hi, yes you could cheap wood and waterproof plywood. Not sure how well pine glues with epoxy... You can also save money by coating all the faces inside the tanks with only one coat of epoxy and only the exposed ones with the 3 recommended coats. Also no need to paint the boat with 2 pot primers and 2 pot paints. Also since pine is heavier you could downsize all the 19x19mm interior gluing cleats to 15x15mm Using 6mm for the bottom will save you money compared to using 5mm and then having to glass it! You should still get a few years of use out of them. Buy good wood for the mast tho! You can also get two old windsurf masts to make yard and boom. 😉
@pontuswendt24865 ай бұрын
@@TheBoatRambler Thanks for the well written answer! One step closer to putting all preparations into practice! Looking forward to next video!
@hurdurdur7rl6965 ай бұрын
Nice progress with the boat! There's a video out there about the goose in rough waves - throwing water up from the center case, how do you plan to tackle that? There is a video called "Sailing Oz Goose in gusty wind" where at around 10 second mark you can see it, it seems the hull angle just bumps the water in there.
@TheBoatRambler5 ай бұрын
Hi, I have seen that video before and I must confess it worried me a bit as I like a dry boat. I might fit a centerboard gasket similar to what you have on a 420 dinghy but I don't think I will bother with the recess on the bottom...
@LuckyTown775 ай бұрын
PD Racer ?
@TheBoatRambler5 ай бұрын
OZ Goose! 😉
@RustyKnorr5 ай бұрын
Again, no eye protection, no mask. If you’re doing an educational video, use proper safety equipment!
@TheBoatRambler5 ай бұрын
Hi buddy, I don't make educational videos nor do I intend to be an influencer, I'm just showing ppl my skiff build. People are free to do as they wish, use safety gear or not, it's a choice...their choice.
@colrodrick87845 ай бұрын
@@TheBoatRamblerI’m assuming that we’re all adults here, able to read manuals and weigh the risks. I agree that it’s better to be safe, but sometimes it’s more effort than it’s worth. I have a mate who refuses to have a guard on his angle grinder. He says it’s easier to see and that’s important to him. He does however use a pair of safety glasses ALWAYS. In his case too many trips to the hospital to remove metal bits from his eyes.
@TheBoatRambler5 ай бұрын
@@colrodrick8784 there's one tool I dont mess about with: angle grinder! I NEVER use it without wearing safety gogles.
@LuckyTown775 ай бұрын
Again the worst offense on the internet this week.