Easy way to repair and calibrate micrometers

[@jurdyswisher5460]

GREAT video. I just took over QC at my company and we had so many mics out of service because of barrels were off and I guess no one took the time to figure out how to fix them. This was HUGE help thanks!!

[@longboard3ng]

Same! This vid helps tremendously

[@stafvanopstal]

Thank you for this detailed video. The tip to tighten the micrometer in a bench-vice was exactly what I needed to adjust my tool perfectly.

[@DeathMetalDavie]

Lacy to wx poor

[@JasonTylerRicci]

I just inherited a vintage Browne and Sharpe that needs minor adjustments. Your video helped me do so

[@brucewilliams6292]

Thank you so much! Just bought a used micrometer and its thimble was off by 15 thousandths from the digital reading. It's a digital Mitutoyo and it works the same way on the thimble assembly. I really appreciate the help.

[@BigParadox]

Thanks! I just bought a micrometer and I did not understand that small part of the key, the one you used first, to make the first adjustment. Now I understand it all. Thanks again!

[@mixedsurface]

Thanks for the great video. I was able to calibrate my cheap Alltrade micrometer using the technique you showed here.

[@brianjohnson217]

Thank you very much for showing how to repair / reset a micrometer. I dropped mine and couldn't get the calibrations back in the original position. I didn't know the procedure on pulling the barrel out procedure. Can't wait to get in my workshop in the morning and cure the problem

[@davidhershberger7899]

Thanks for sharing this video. I am taking some machining classes right now. Watching this video filled in some gaps I didn't understand when reading how to calibrate a mic.

[@HomineDomine]

Thanks a lot for upload this video, dear friend. I need this for calibrate a micrometer Mitutoyo. Greetigns from Chile.

[@flodgey]

Amazing camera work bud, totally didn't give me a stroke.

[@schuelfish]

Did you not read the description? This was done 7 years ago with a go pro 🤷‍♂️

[@flodgey]

@@schuelfish I know, I was just joking around, sorry if that came out bad.

[@schuelfish]

@@flodgey you got a laugh out me 👍

[@ryanmyers2877]

Thanks for the help! Needed to measure my cylinder and piston on a quadzilla 500 they were out beforehand.

[@schuelfish]

Awesome!

[@christopherhasert6861]

Had an issue with a customer mic. The zero was position 90 degrees down when i checked it. But when i saw how you popped the barrel off, I did the same to the mic I was working on and it reads perfect across the range. Just when you think you know something, you learn something new.

[@zahidabbasi5614]

Very good video regarding zero adjustment i like this technic. THANKS

[@TheGeezzer]

W⭕W this was very helpful and helped me celebrate my fussy Xmas present mic...it was 3 microns out on the vernier with a very stiff sleeve. The thimble removed easy and I managed a good zero-line-reset. I collect quality mics, have about 15 of em, all B💥NG on accurate to the micron or 10thou.

[@mordimustafa1275]

great video

[@petertyrrell6690]

Great video. Thank you.

[@mikehunt5934]

thanks for this

[@rsitch1]

Great to know,thank you….Bob

[@pauldiaz4273]

Great video thanks!

[@arumugamm1400]

Our mic 0.25 positive err, Thankyou so much sir

[@harehare280]

Great job thank you

[@lnna5462]

I have one with the pointed spindle. One end is broken, how do I take it out and replace it?

[@axa.axa.]

Is this also valid for Brown and Sharpe?

[@schuelfish]

Yeah they are all pretty much the same.

[@paulmorrey733]

Thanks

[@Sol6567]

Thank you very helpfull

[@AsianBlackR3501]

Thank you.

[@petermoses5095]

first step after using test peice is to doble check all faces clean . the check again . I seldom have had to adjust a micrometer despite the fact they are used often and often not treated well

[@saidarshankrishnank.p4434]

Very good & usefull vedio

[@WIZARDWERX]

thx

[@michaelbrian219]

Help me setup a mic and get the thimble back to zero setting. Thanks

[@pg6429]

How to remove and correct 0.1 to 0.3 error in micrometer??? please tell me...

[@schuelfish]

What kind are they?

[@pg6429]

0 - 25mm, 25 - 50mm, 50 - 100mm, 100 - 125mm (least count 0.01 and 0.001)

[@mauricio201212]

thanks i fix my is working good

[@erebusterrornm5184]

Благодаря!

[@unnalmudiumnanba4939]

Tq useful msg

[@funnystuff2591]

Great video

[@rakeshchouhan4195]

Thanks