Communicate siemens S7 300 PLC with Sinamics G120x VFD Drive via profibus using TIA Portal Part#1?

[@yveso7916]

Thank you very much, was looking for this because we're replacing MM440 to G120 on Profibus.

[@mongiAa]

good effort, godd explaination, continue with upgrade simovert vc to sinamics G120, Thnaks

[@maximjones1446]

How you determined the hexes command for Cotrol ON/OFF = 047E and other commands? Where is the its sources?

[@williamcernich5889]

I was wondering the same..

[@mughal1648]

Thanks a lot. We are going to replace old Siemens MM to SINAMICS G120. I was looking such video,

[@muhammadshehbaz7765]

amazing video, really helpfull for engineers. keep making videos.

[@muhammadshehbaz7765]

but not able to download file properly, sir please the problem.

[@EASYPLCTRAINING]

Any error in download ?

[@muhammadshehbaz7765]

Now able to download

[@Khatu_ki_sarkar71]

Very very helpful for beginners

[@a_sava]

Thanks for sharing this. You saved me a lot of time.

[@mirzamansoor243]

Thanks for uploading this type of Videos.

[@engmohamedrefaat5679]

Thanks for your efforts need video about communicate s7 1200 with abb acs 550 or acs 580

[@rsinurat2144]

Same🙏🏽

[@raviprabhat2392]

Please upload a similar video for S7 300 communication with Parker 590 or 690 plus drive..please

[@louzehimolevy4153]

Hello sir, I appreciate a lot your in making tutorials. And also I would like to take an online PLC training with you if possible.

[@andreicaza6145]

I am getting a Fault F1910 and I do not know why. I am using your codes 047E, but the moment I put "HIGH", it gives me that fault. Do you know why?

[@imranmirza5775]

thanks brother super effort ................... please suggest me TIA Portal version which you are using in projects...........?

[@EASYPLCTRAINING]

V13 mostly

[@imranmirza5775]

@@EASYPLCTRAINING Thanks

[@ngoile876]

i don't have g120x on Tia, Could i choose others? is it ok?

[@EASYPLCTRAINING]

No , check online on siemens website forum for correct gsd file

[@palanipps]

Sir one doubt could you plz?. the Gsd file is common for all Siemens model drives or different gsd files for other model Siemens vfd?

[@maheshbhilare6430]

Thanks for vedio.... Make one vedio on how to tak wincc flexible running back-up with its Recipe... I have tried ... But not able to restore it's old recipe

[@inaramara2416]

please sir , from where you are getting those codes for words ?

[@souravdas2506]

very nicely explained, thanks

[@umarafzal4926]

its very help full thank you soo much sir please can you tell theirs only one perameter p918 we need to set on drive side and after that our plc to drive communication is done.?

[@dhavalmaheta3428]

Helpful video thanks

[@rajendravaidya6482]

How to solve CU busy errors

[@motor519]

Parameter to Drive g120 ??? . For setting profinet

[@newkhmer3591]

What program in the OB121?

[@iqbalmehedi3423]

nice video. please make SCADA for this motor control.

[@AzhaguRK]

Thank you ❤❤❤

[@kiranchoudhari4717]

Good information 👍😊 brother I understood 💯

[@kiranchoudhari4717]

But the Google drive file doesn't opening even in laptop

[@EASYPLCTRAINING]

Let me check once again .....

[@jobsinpakandgulf621]

Sir 067F was missing reverse bit

[@aarifbobade2403]

Good knowledge.But i was searching one thing.i replace one of simens drive but its showing BF Fault.i have copy the prameters by bop and paste with another.I thing communication issue.can you help me.

[@EASYPLCTRAINING]

What is drive model ? Is it profibus ? Check the drive profibus address in the parameters , old and new drive address must be same , ..... check the Dip switches for the profibus address under the BOP . Set these dip switches same as old drive....

[@EASYPLCTRAINING]

After setting profibus address , power cycle the drive , OFF and after 2 minutes turn it ON

[@aarifbobade2403]

@@EASYPLCTRAINING Thanks for your value response.Yes profibus ethernet cable,no dp switch, model no is 6SL3210-1KE11-8AF2.What is parameter for profibus address.

[@charlesmwangi164]

How do you trouble shoot Siemens VFD

[@bobeldukla]

Super. Thank You very much....

[@alrazi6687]

why we add standard telegram ftn?? what is the need of this ftn here?? pls anyone expain

[@mohdirshadshaikh444]

Very well explained!! I would like to know if I want to run/stop the drive via digital inputs only and speed reference to give only via profibus, what parameters do i need to set for that? As of now when I established the communication via profibus then now I'm unable to start the drive via digital inputs!! Please help me with this

[@EASYPLCTRAINING]

All PROFIBUS DIP switches = OFF --> Address defined in P0918 is valid otherwise the DIP switch setting has priority and P0918 indicates DIP switch setting. check address in OLD drive paramter p0918 and put this address in new drive and save it and power OFF and ON the drive.

[@muhammaddanishhameed9865]

Bhai, servo motor control with plc par bhi video banayein.

[@EASYPLCTRAINING]

Sure

[@jmmedia679]

Why did you use TIA portal...could it not be done in simatic manager?

[@EASYPLCTRAINING]

Yes

[@jmmedia679]

@@EASYPLCTRAINING same procedures can be followed to configure it with simatic manager.. right?

[@EASYPLCTRAINING]

@@jmmedia679 sometimes somatic manager don't have gsd files for new drives , thats why better to use tiaportal.

[@vorapobautomation9760]

How to Communicate siemens S7 300 PLC with Sinamics s120 VFD Drive via profibus/Profinet using TIA Portal on VDO ?

[@gouravgaming5541]

Sir, please make a video on SIMOCODE programming with s7-300 plc and control from HMI TP-700 Comfort. It will be really helpful.

[@ameysawant5695]

sir, can you please tell me, how you calculate that hex value to control drive.

[@EASYPLCTRAINING]

kzbin.info/www/bejne/ppqwnWp9mN13epo

[@bakilsorory3516]

thanks brother nice video

[@Bigmallone]

thank you for the video

[@bezzila]

Thanks Super!

[@tayyubindustrialcontroleng8447]

Awsome👍

[@kgauravb]

👍👍

[@anikdebnathopu8082]

Tnx bro

[@EASYPLCTRAINING]

Please ask your friends to subscribe also

[@vorapobautomation9760]

How to Communicate siemens S7 300 PLC with Sinamics s120 VFD Drive via profibus/Profinet using TIA Portal ?

[@EASYPLCTRAINING]

My friend give me some time , I will make a video , you can search in Siemens forum .... there are lot of topics that will help you

[@vorapobautomation9760]

I will waiting you make video