What is Safety Relay PILZ ? Easy Explained | pnoz X2 X3 X4

[@Lorenzo-c5q8w]

Thanks, now it's clear for me.

[@octymocty132]

thats made me look 100% right in an disgruntled converstaion over pilz verry clear and easy to under stand for the aprentice only thing i would say is use orange cable for controll identification as yellow is a no no thank you

[@marijngade5403]

Would this setup not require 2 master relays in series to consider it full safe? This way the relay could get stuck open and the intire safety part is useless.

[@pnswg01]

In the schematic section, the wires goes to the wrong pins but the audio is true. Possibly because the software wouldn't allow you to draw the lines to the correct pins. Good explanation anyway.

[@Jatin____Sharma]

Awesome, today I learn about a new device😍

[@judeclark142]

thank you so much i finally understand safty relays

[@kevin00861]

Thank you Sir for spreading your knowldge

[@EASYPLCTRAINING]

Welcome dear

[@The11noodle]

Brilliantly explained

[@maintenancegc6568]

Clear Explanation.

[@syedhassanali9330]

Thank you very much sir very informative video

[@monroestrike4378]

Perfect. Simple and well explained!

[@alfredaxax]

nice lecture

[@baskarchandrakasan995]

Excellent teaching sir.

[@irwinjimenez]

Great job. Very useful video. Thank you.

[@xubairahmed951]

amazing work

[@afrid-li8ke]

Great and well explained

[@arunrajendran674]

Super explanation... Explain pilz X3 relay also?

[@EASYPLCTRAINING]

Stay connected coming soon

[@ismatsumarjan290]

Thanks for your information

[@AEGroupNL]

You can put 100K in the thumbnail :) thanks for the video!

[@chappagiridhar5109]

Nice explanation sir👍👍👍

[@vasanthakumar8167]

Good explanation

[@showshocka3k]

Love it! Controls!!

[@kencooley5589]

I have a question. If one of the channels are not closed when the on pulse to the start channel is made, do you have to turn off both channels to attempt to start it again? So if channel 1 is false and channel 2 is true. Start signal is received. Must channel 2 be made false before another start signal can be made true?

[@EASYPLCTRAINING]

Yes exactly we have to reset both channels ..... but in some relays we jut have to reset only one faulty channel .... I think It depends on the model of the Safety relay

[@user-saber-yasser.]

thank you very much 🌹good explanation

[@hatemzaatra5894]

Great video

[@Bigmallone]

great work it was very useful for me

[@cathleyamaesantos4557]

Nice one

[@azharbarmare6847]

Sir I had a question in my case relay is starting but after some time but it is continuously asking to reset and sometime reset button also dnt work...

[@shahbazarain9488]

Amazing

[@devpatel361]

Do I compulsorily have to use a Contactor at the end? If not, do i attach 13-14. 23-24 directly to the actuator ? Why use contactor, if we are using relay for the saftey ? Thank you for the video ! :))

[@glennrodrigues7111]

Thank you sir well explained

[@RAMSINGH-0]

Thankyou ❤

[@mantunaik9798]

How to take feedback from this safety relay to plc for alarm generations

[@aminizza1450]

Thank's very usefull

[@manjunathamanju6204]

Good explanation thank you so much

[@shanefrank3281]

Great video! I have been having trouble understanding safety relays from the data sheets and this helps. But I was wondering if you had only wired the contactor to only 13-14 (and not series 13-14 and 23-24) would only the red button connected to S11-S12 turn off the contactor? So S11-S12 safety input only controls 13-14 and S21-S22 only controls 23-24. Is that correct?

[@GhostHostMemories]

no. 13/14 and 23/24 are mechanically linked, and not tied to a specific input

[@johnrece6622]

So this relay doesn't have a reset option? So you will have to turn off channel 1 and 2 to restart it?

[@TheThippu]

Excellent i have learned new thing today, Is it same as Siemens Sirius safety relay with more chancels

[@Jarito1903]

Great video, thanks. Keep on the hard work

[@Love__yu]

The contactor is 24 v?, how can connect a 220v contactor

[@MenAreBrave07]

Using relay.

[@irwinjimenez]

220v can go to COM terminal, NO contact goes to the contactor coil. Safety relay energizes the 24vdc ice cube relay to turn on the 220v.

[@phanduyautomation3737]

perfect. good

[@antoniomondragongonzalez1692]

Excelente

[@danghoangvinh9512]

Perfect. but i have a question. Why do you have to wiring both 2 NO 13-14 and 23-24 to contactor instead of only 1 (13-14 or 23-24 to Contactor) .Thanks you about this video!

[@EASYPLCTRAINING]

You can use single contact also , just as an example I looped both auxiliaries . These contacts are also used to give signals to other safety relays ... means if you have seen safety relays working in loops

[@danghoangvinh9512]

@@EASYPLCTRAINING thanks you!!

[@cascadeanalog320]

Thank you Sir

[@showshocka3k]

How could one even attempt to give this simple tutorial thumbs down?

[@danschumacher5427]

Watch me

[@ajayrawat9525]

sir PNOZ S3 have same function or different?

[@EASYPLCTRAINING]

Same function, but I thing It have 4 channels to monitor the safety loops

[@balachanderbalachander6959]

nice sir. add other company relays also. sick, schmuller.

[@EASYPLCTRAINING]

Almost similar .... but must go through wiring diagram

[@ethan073]

THANK YOU

[@athilaldurry5880]

Many thanks

[@mikeadler434]

👍👍

[@goriparthisrikanth646]

Sir video prepared in three phase motor runs in single phase supply okk

[@goriparthisrikanth646]

Plz reply

[@EASYPLCTRAINING]

Yes three phase motor , running on single phase 220v

[@goriparthisrikanth646]

@@EASYPLCTRAINING plz video prepared sir

[@ThePengue]

Why to reset the safety relay you have to push both red button?

[@sebutir_embun6703]

thanks bro

[@asifislam7376]

Neutral A2..you draw black wire in s12..channel 1 s21,s22..but where u have drawn red push button? 14 and s11..how!! One red push button should be in ch1 (s22,s22) and another one in ch2 (s11,s12) Am k right? Pardon..

[@Idrathernot.]

Very beginner here; what does K1 and K2 mean?

[@EASYPLCTRAINING]

k1 and k2 are the internal relays of the safety device

[@jwerry58]

Can you provide what type the 1 green button and 2 red buttons? Momentary or Latch? Red N.C.? Green N.O.?

[@MenAreBrave07]

He said it need pulse signal which means momentary.

[@foxxmulder7524]

This is incorrect:Channel 1 and channel 2 is not wired using single pole normally closed contacts. You must use double pole force guided contacts. going to both channels simultaneously.

[@mosesmoyes3301]

Piloje

[@AndrewBambiliano]

Sorry but your bad wiring diagram made me so confused

[@pogssss5058]

Thanks for this sir,

[@박정훈지훈]

Can you provide what type the 1 green button and 2 red buttons? Momentary or Latch? Red N.C.? Green N.O.?

[@EASYPLCTRAINING]

All momentary button .... green NO .... and red NC push buttons

[@박정훈지훈]

@@EASYPLCTRAINING Thank You ^^