Do not buy that bearing tool kit off of eBay or Amazon. The rod stripped out causing me to take the spindle to a shop to get the bearing installed! Thanks for watching. #honda #hondaaccord #hondaaccord2020 #youtube
Пікірлер: 35
@RonaldDCass Жыл бұрын
I suspect you never lubed the bolt threads AND the washers that need to be installed. Also it's possible you used the wrong size back plate to pull the bearing out & weren't properly set for removal. Also it's advisable to use a breaker bar until the bearing is broken loose then the impact wrench can complete the job. Just buy a new bolt to use in the future. Make sure it is grade 8 with full threads or plan on using spacers to allow the less threads, then LUBRICATE as mentioned above.
@Pinozcyclezandridez Жыл бұрын
Thanks
@sd9062384 ай бұрын
I've heard the instructions on the press kit say to never use an impact wrench. And as the guy above said , lube the threaded rod.
@robertfrate9738 Жыл бұрын
Hi, I have this press and it’s great tool, it pulls the bearing out and installs it with no problem, I greased the forcing well and I pulled the rotor off first before I pulled the hub off, I used a too jaw puller to pull the hub off and came right off, I shouldn’t have to say I pulled the axle nut off first,
@KaziSolo Жыл бұрын
This was user error all the way he never really knew what he was doing from the moment he was trying to slide hammer with the rotor lock still on 🤦🏾♂️
@Pinozcyclezandridez Жыл бұрын
Nooo the little screw stripped out so I tried to pull the hub anyways…the tool did strip regardless.
@litbasegaming346515 күн бұрын
@@Pinozcyclezandridezyeah but the rotor was locked in even if it stripped why would you pull it?
@Pinozcyclezandridez15 күн бұрын
@@litbasegaming3465 yeah it was a bad day! Thanks
@mattcurtis3941 Жыл бұрын
I hope that’s his own vehicle and not someone paying him to do this repair.
@Pinozcyclezandridez Жыл бұрын
I got paid well…thank you
@calholli4 ай бұрын
You can't pity pat with the slide hammer.. You have to throw it like you're trying to break the tool.. and then it works
@royquesada5295 Жыл бұрын
Then you hitting the cv shaft with hammer😮😮😮 you leave the nut on a little flush and then strike it, unless of course you are planning to replace it.
@vitk5464 Жыл бұрын
USE WD40 first. Dry removal will not work.
@deanrss1 Жыл бұрын
Set up is definitely wrong I've used them on many and there fine I just use a bit of engine oil 🇬🇧
@Pinozcyclezandridez Жыл бұрын
Maybe mine was defective…weird
@calholli4 ай бұрын
Lol.. The rod didn't strip. I can literally see the impact moving your wrench up in the air. You have to HOLD IT. If your impact is moving the wrench, you're not unscrewing anything; next time, let the wrench spin until it ruins into something and holds itself solid. .. Also, that impact is too weak. You would have needed to wrench on it yourself with a ratchet.. Just get a 3 or 4 ft cheater bar and it will definitely comply... If those threads were really stripped, you would have shown it to the camera.
@JasonSmith-qx3zh Жыл бұрын
To lite need the ten-pounder!!!
@Pinozcyclezandridez Жыл бұрын
Probably
@liketolearn141 Жыл бұрын
You have it on backwards too if I'm not mistaken the bearing is pressed through the back
@Pinozcyclezandridez Жыл бұрын
It comes out through the front. Removed with hammer and pressed in at shop.. Your thinking when you unbolt from rear. I think I should have oiled it or something…
@liketolearn141 Жыл бұрын
Sometimes, you get bunk bolts that come in the set. That's why I used a harbor freight set. 90-day return and right down the street. lol if you don't like it, return it for one that works
@Pinozcyclezandridez Жыл бұрын
@@liketolearn141 yeah that’s probably what happened…