How to install an automatic door closer

[@luckydougfergus]

I struggled for five hours trying to install a new door closure before I watched your video and then within 15 minutes I was finished and now it works perfectly! Thank you very very very much!!

[@kunalg.1443]

Same here

[@ThelmaChambers1]

this is the clearest and best video on this subject. I found the instructions that came with my door closer completely impossible to understand and so had to rely on videos to get it installed. I found the whole process horribly difficult but I got there in the end. THANKS !

[@ecologicaltime]

thank you

[@rickrahrig1442]

Instructions on mine were terrible. I had it started right with the body then it all wemt to hell. So simple with instructions like his.

[@andriannap2048]

Η πάνω βίδα και η κάτω βίδα τι ρυθμίζει;;;;

[@rodcramb9401]

My door closer is identical. My instructions in Chinglish are also identical, except that there were no dimensions or measurements printed on mine! Thanks so much. I don't often get stumped, but this one had me.

[@alexbrown1995]

5 years later and it's still useful. Thanks, mate!!!

[@ungratefulmango]

Really helped me wrap my head around it. It's quite simple once you understand it, but a little intimidating to begin with. Thanks for the comprehensive and concise video.

[@paristexas72]

THANK YOU FOR POSTING THIS. I've been watching tons of videos and reading lots of stuff online and finally I figured it out thanks to your amazing and simple demo... much appreciated!

[@wetinbidat]

Best video in this topic on internet! Thank you so much for your very clear, simplified and demonstrated steps. Best hands down!

[@ecologicaltime]

thank you

[@robertmacpherson4538]

If you're in the UK, this particular door closer is the "Asec VT10055 size 3 contract door closer c/w cover in silver". Mine came with no detailed instruction, so this video saved the day.

[@ronaldvlug9403]

Thanks, I installed it at my door. That wasn't possible without this video. 👍🏻👊🏻😊

[@sultanbdr610]

Thanks a lot my brother for your perfect explanation. The first door closer fits without looking to the instructions cuz it’s written in your own mother language not English or Italian only one language .... any way also I have watched some video. Thanks again,, you have a gift which is you can deliver your idea simply with blest Confidence to my mind and other people as well. Lectures and doctors in unis unfortunately 10% of them has this confidence and only talking into the main steps pla pla pla hahaha ,,, too much words. Many thanks from Saudi Arabia to you and everyone here watching. Sultan

[@ecologicaltime]

appreciate your comment!

[@thejawbone]

Well done, your video is very, very educational and helped me install the unit properly

[@halfrocanadianv5086]

Thank you. I had to throw one of these on for first time in a long time at my job site last Friday and I was over tired and completely messed it up. Watching your video helped me figure out exactly where I went wrong.

[@bethrika66]

We put our door closer away for bout 5 years. Watched this useful video and voila!! Installed

[@Yk-xw8lm]

Thanks. Why did you keep the tension when it is in rest. I mean you should have fitted the knuckle straight

[@andrewkimber2256]

Thank you for this really helpful video - much appreciated. You explain it all perfectly.

[@GilangMagrial]

2:10 Do you use Inch or Cm ??

[@andrekrisanto]

great information bro, i tried to install last nite, after that my door can't open. will continue tonight after watch this great information. thanks anyway

[@WichaiPhutyaem]

Thank you very much indeed. I bought a second-hand one and didn't know how to install it. This video did help me a lot.

[@ahmedalmasry6177]

Realy you are the only one who helped me to install my door closer machen, just i took 5 minets to finish this work exactly. Thanks alot

[@ecologicaltime]

Glad it helped

[@frankkante7850]

Great, i have the same doorCloser without manual. Now i know how to Install. Thank you.

[@hendrikjbboss9973]

I did it your way and it works! !! Thank you for a flawless tutorial! !!

[@voodoomotion5855]

Thanks for this great video,, do these stop people slamming the door shut?

[@ecologicaltime]

yes

[@contactwundermax8163]

Thank you for your video and the clear explanation. Easy steps to understand, definitely matching my needs.

[@hendrikjbboss9973]

Thank you for your excellent tutorial specifically with the dimensions from the edge of the door. Since I seem to have the exact same model, but in another country, I can now confidently install my door closer tomorrow morning 👍

[@livenotonevil8279]

does anything need to be done with the shaft that sticks diwn from the bottom (where you placed the cap at the end)?

[@mariuszkedzior1541]

How to convert moles to inches , or centimetres ? Because my measure tape is in centimetres, and inches only .

[@mrciso]

It's not moles, it's mills as in millimeters. Aussies pronounce it as moles. 10mm = 1cm.

[@jjkobusp0]

Did you have any problem with the auto door mechanism hitting the brick wall? Would it still work if you moved it slightly more toward the door opening to avoid the brick wall? or just door stopper on the wall or floor?

[@ecologicaltime]

no there is sufficient clearance by the brick wall. You have some room to shift the door opener left or right, keeping in mind that shifting too much will limit the range of opening.

[@hectorheath9742]

Same hinge/ door orientation arrangement with my application. This clarifies the job. Many thanks.

[@VijayRamachandran]

Thank you for the video, it is very detailed.

[@p0k7lm]

tnx 4 vid , had lots of complications , instructions had wrong size schematic , door was hollow metal , had to drill each side seperately , using one through the door hole to use as reference for other side , had to use actual part for pattern layout , had to get special low profile flat nuts and bolts to bolt to door , ate up much time , no convience at all , never do again on a exterier metal door 👎🔨🔩🔧

[@normanmcintosh4241]

Great instructions, thank you. I can now get my one done.

[@kunalg.1443]

Thanks for giving me a information.. I was seen lots of videos but you are amazing 👍🏻👍🏻😊😊😊

[@danieltobaezekiel846]

I fitted mine yesterday but it is so hard to open. It takes much strength to pull to open.is there any way to soften it while opening

[@MrLaxr-op4be]

2019 ... Helped a lot !!! Thanks for the content !!!

[@Newb118]

Hi nice video, does it matter if the top bracket goes to the left or right? Also im sure the screws that do the speed dont do anything on mine

[@rokicarevic]

Very nice tutorial! Thanks!

[@JennyGenevieve-b4z]

Hi, I wish the workman I used to fit my door closer had seen this - He's been around twice now and it's still not installed properly, It's a Smith & Locke Series 3 Overhead door closer

[@jimharris9877]

Who is the manufacturer of your door closer & what is the model number? I think I may need one soon and I like the one you put up on your door. Thanks!

[@ecologicaltime]

UNION Door Closer Medium Duty - Silver. Dont have model number.

[@jimharris9877]

@@ecologicaltime Thank you!

[@rogerjuman435]

Thanks a lot, this helped me at the office door. Roger Juman

[@unboxstudio3470]

I am facing issue that its very hard to open the door..i have adjusted closing and do not have issue with it.. can you advise?

[@Nahid2624]

Thanks for this helpful tutorial.

[@rogerpattube]

Was the main body supposed to double as a door stopper against the brick like that?

[@ecologicaltime]

dont understand your question. There is no door stopper in this installation. The video shows that the unit has two speeds and slows towards the final few degrees of movement. The stopping of the door is caused by the door frame as usual.

[@khankargili]

Hey my door is too hard to open. How should I adjust the screws 1 and 2

[@kanalord4134]

Very nicely done ! thank you.

[@generally_good_guy]

Mine is a brand new unit and won't shut if door open past 70 degrees. Door can only be opened to 90 degrees so almost all good. How do you adjust this part? The two screws on the end of the unit do not change this area

[@ecologicaltime]

it may be that you have installed the arm already past the mid point of the travel. The screws affect the travel speed at different arm positions. Please check your arm when its disconnected from the door. It should not be highly loaded when does is closed.

[@fst1775]

It’s because your door closer has a hold open, look on the instructions of there are any adjustments on the arm, otherwise your closer would be internal hold open and the only way to make the closer hold open further is the remount the door closer body and shoe closer to the hinge.

[@markhooley1525]

That piece of paper you had with the drawings on is an actual sized drilling template

[@ibrahimsued4906]

How to install it for having its arm laid parallel the door? I've once seen this kind of install ........

[@ashker9978]

Helped alot thanks 👏👏

[@krystalhandley3387]

If the door seems to have to much pressure (meaning you need to push hard to open) then what needs to be done?

[@ecologicaltime]

have you placed it correctly? Yes it does add a fair amount of resistance once installed.

[@SD-ir1vf]

Loosen up the bad check valve. Go by quarter turns to the left until it works right.

[@luciameanos3691]

@@SD-ir1vf what's the bad check valve? I have the same issue

[@SD-ir1vf]

Back check valve. Its on the top or the bottom of the closer. There are four adjustments. Sweep latch power and back check.

[@SD-ir1vf]

Lucia. Remember that it’s a hydraulic adjustment And you don’t want the end of the screw to protrude outside of the casing or the pin will shoot out and the oil will come out of the closer.

[@crand20033]

. My door is a tough to open, how can I make it easier to open. How to decrease the resistance to opening?

[@billybelmonte]

Great help thank you.

[@undarkwin]

following your video, I succesfully installed it👏🏻👏🏻👏🏻👏🏻

[@1billwill]

Thank you great video.

[@harishsingh8063]

Beautiful inspiring information 🎉

[@grigorasmarianvasile497]

Thank you for explication !

[@wojtas-4]

Korpus samozamykacza przy maksymalnym otwarciu drzwi uderza o siane. Da się to tak zrobić by nic nie uderzało o siane i jednocześnie samozamykacz działał jako ogranicznik .

[@Asmara1991]

What's the price?

[@durgeshsrivastav9626]

that was a real help for me Sir ! Thank you

[@sebirulangit9225]

What's the cap for?

[@ecologicaltime]

just for looks

[@user-uj9gi3ol1f]

As I could see, the closer does not work correctly. The door should close quickly and only 15-20 degrees before closing the closer should slow down the door (both the angle and the closing speed are adjustable). On your closer works the other way around, the door moves slowly, and before closing (15-20 degrees) the door moves faster.

[@kevindowling6530]

Thanks for showing this great video

[@abudais3919]

It work👍 tq

[@kalidnemo1669]

What if it needs too much force to open the door What the problem

[@SD-ir1vf]

Loosen up the bad check valve. There are four adjustments. Latch sweep power and back check.

[@luciameanos3691]

I have the same issue, too much force to open.. could you solve it after all this time?

[@fst1775]

@@luciameanos3691 if your closer has a power adjustment then adjust the closer to a lower power also if your closer does not have that then re mount the body and shoe closer to the hinge

[@ZueGeey]

Very helpful. 10Q

[@QUIX4U]

Tension ? What UTTER Bollocks. Those two screws (there) at 5:58 do absolutely NOTHING for spring tension. All they "DO" - is alter the needle-nozzle openings in the oil-ways, to allow a quicker or SLOWER movement of oil from the pistons inside the unit - to enable the user to choose the speed the oil is allowed to PASS these two adjuster screws, so that you either have a SLOW door sweep (closing) action &/or a door LATCHING speed. They do absolutely nothing other than open or close off, an oilway.

[@DeltaModelX]

if you know so much why dont YOU make a video about how to install this

[@2mad2bad]

Thanks mate, great video.. problem solved!!

[@cbhrcbhr]

You do not need to mesure, stick the diagram on the door, and make holes where it is said

[@hendrikjbboss9973]

Not all models have templates 😠

[@Ajipanda]

Ok tanks mr is very very good

[@andriannap2048]

Μηπως μπορεις να με βοηθήσεις; Τι κανει ακριβως η πανω και η κατω βιδα για να καταλαβω !!!

[@gura-nkoomjoel5679]

Perfect work

[@ericlefleur1845]

Very useful tips

[@richardpaul5703]

thanks my friend

[@servico100]

why is it speeding up on the latchcheck

[@ecologicaltime]

has two speeds

[@chuwongsevathanodorn9731]

TanK you verry much

[@1Patient]

You put it upside down.... Closer mounts to frame and arm attaches to door. Oh, I see it wouldn't mount that way with the brick and the closer....ya ya....I see it now....Is that your Wine Cellar??

[@clemsbeauty2916]

I installed a door contact. It beeped twice during power up and stop beeping. When I open the door I don't hear that nice song again.

[@ziadalotaibi5177]

thx clear explanation

[@user-suttiphong]

Thank you very much.

[@lukwinnie242]

If you need door closers , please contact us. We are manufacture in China.

[@MgundaCJCossie]

That's great

[@darrentwine2590]

Why did you not use the template?

[@rogerpattube]

Said he did, just not on the vid :-) 2:58

[@thegreatmycountryindiasanj8033]

Thanks dear bro

[@korgrocker]

Excellent video

[@markanderson3874]

Sweep and latch

[@mouzam.s.7392]

the door become very heavy my kids can't open it😢

[@amjadhossain3277]

Thank u sir

[@DeadlyVenomKing]

A template would be useful Potna

[@erikajones3013]

00:00 10:09

[@dizzyiguana981]

Mt main arm doesnt turn

[@spicer7]

Thanks

[@kelvinmgendwa1438]

Good

[@SAYEDSAYED-nj9sk]

🌹🌹🌹🌹🌹🌹🌹

[@insafnajahi95]

This is wrong brother because not have 90% digress

[@stiliyan66]

Hahо, no need to measure, this is template :D Also must be on 90 degrees! Everithing is wrong!

[@abrheemmr2395]

🙏

[@iginolima968]

Coomo. Ouvir em portugues

[@singleoneline1799]

❤

[@thomaschristener2902]

Sorry, the arm should not look that way and that product is ultra cheap rubish. If you want a door closer, buy a Tjss, Geze or Dorma and let it install by a pro. One leg of the arm - depends on the brand and product - ALWAYS stands in a 90 degree angle to the door / frame. Otherwise the closer don‘t work how he should because the adjustements don‘t react on the same point. Better: don‘t install it self. There are too many models for too many specific door situations. (Mounted on the side against the hinches, mounted on wide or thick or both doors, mounted in the steelframe.....) A course for pro‘s at one of the market leaders takes a full day. For a not pro, it is not possible, to find the right closer type for a specific door.

[@vincentneo7258]

Mom.

[@hillsrivers]

Very nice demonstration