ECOSMART Remote Color Changing LED Light Bulb

#ECOSMART #LED #Lightbulb #Remote #Colors #Light #easyinstall #easyinstallation #outdoorlighting #lighting #diy #honeydolist
ECOSMART 1006 778 604: 60-Watt Equivalent Color Changing LED Light Bulb with Remote
Purchased at Home Depot for $12.97: www.homedepot.com/p/EcoSmart-60-Watt-Equivalent-A19-CEC-Color-Changing-LED-Party-Light-Bulb-Starter-Kit-with-Remote-1-Pack-11A19060WRGBW01/318284633
GrayTrend, LLC
Link Tree: linktr.ee/graytrendllc
Facebook: GrayTrendDesigns
Instagram: graytrend_llc

[@brickdorsi]

This f thing will not connect with the remote and no one is showing how to link the remote to the bulb unbelievable

[@GrayTrend]

How to pair the remote: OK, I didn't go over this because I'm not going to purchase additional lightbulbs, but here goes. This is from the Instructions: 1. Turn on the bulb and hold the remote within 2 inches of the LED bulb while it's on. 2. Press and hold the On/Off button on the remote while also (at the same time) pressing the Dimming button on the remote, so press both of these buttons at the same time and wait 3 seconds. An indicator light should start flashing at the top left of the remote. The remote will start searching for the LED bulb. The indicator light will flash rapidly until the LED bulb is detected The light should flash once and the indicator should stay on for 3 seconds, then go out. This indicates the LED bulb and Remote are paired successfully. Also, if that doesn't work you may need to reset to factory settings. From the Ecosmart Manual it states: Reset to Factory Setting - Using the wall switch, physically switch ON and OFF 6 times within 5 seconds. The LED bulb will show Red-Green-Blue gradient color and then flash twice after a successful reset. Good luck!!!

[@brickdorsi]

@@GrayTrend I brought em back and hot new ones they worked instantly, I needed a day of that day

[@GrayTrend]

@@brickdorsi Sounds good. Best of luck to you!!!

[@msladyconnect]

Mine has been stuck for months

[@msladyconnect]

​@GrayTrend thank you soooo much!

[@markmannm2]

I have an echo smart multicolor light bulb with the wireless remote the wireless remote went missing and I'm wondering if I can set the bulb to change colors without the remote if there's a procedure

[@GrayTrend]

Thanks for the comment/question! I wish I had a good answer for you. I've heard there are ways to vary the voltage to change the colors of the LED light (but I've never done it). I checked another avenue which was if the lightbulb was connected to Alexa, but it isn't. Maybe someone can provide a much better answer. I do appreciate that you watched the video! Best of luck to you!!!

[@AttentionReader]

I need this in my life. 🤣

[@GrayTrend]

Everyone needs one of these!

[@BigEightiesNewWave]

I believe they should call it COLOR TEMPERATURE changing, as in Kelvins. I prefer higher-K, sunlight-like bulbs, myself. I see much better.

[@GrayTrend]

Thanks for the comment! Appreciate that you watched my video!!!

[@angelcastillos6657]

I got a question how can I reset it

[@GrayTrend]

Thanks for the comment! To reset it back to a white light, you have to go to the Customize White Lighting button which is the 3rd button down from the top of the remote. It should be from the top of the remote, 1) On/Off button 2) Dimmer button 3) Customize White Light button 4) Color Change button. Hope this helps!

[@jamescostello7584]

Yeah I'm replying again I just bought this the other day and the remote does nothing to change the bulb color when I when I put the bulb and screw it in it comes on a light blue and if I unscrew it it goes off the remote does nothing to change any of the colors or does it shut the bulb off the little red light blinks on the remote but that's all it does

[@GrayTrend]

Sounds like you may have purchased a dud (bad light). I'm not associated with Ecosmart. The best advice I can give you is to contact them via their customer service number 1-877-527-0313. 8 am to 7 pm Monday through Friday. 9 am to 6 pm on Saturday. Best of luck to you!!! Hope you can get this resolved. My light is still out in my lamp post and working fine.

[@rellys6039]

Just dropping in to say I'm watching this as i just bought a this bulb but not install yet. How's it holding up?

[@GrayTrend]

Thanks for the comment! The bulb is still working in my lamp post outside my home. I guess it has been 8 months now. It's set to be blue when it turns on each night. I like it!

[@rellys6039]

@@GrayTrend to follow up for the respect of your video.....I bought the wrong size 🤣! I need a candelara bulb, not this. Exchanging tomorrow for another bulb and brand since I didn't see an ecosmart kind

[@GrayTrend]

@@rellys6039 we’ll best of luck with whichever bulb you purchase! Thanks again for your attention to the video.

[@rosecitysharon]

Do you know how to reset the Ecosmart bulb? 🤞🤞🤞

[@GrayTrend]

Thanks for the comment! From the Ecosmart Manual it states: Reset to Factory Setting - Using the wall switch, physically switch ON and OFF 6 times within 5 seconds. The LED bulb will show Red-Green-Blue gradient color and then flash twice after a successful reset. Good luck!!!

[@january575]

I have 2 of these bulbs and neither came with any key

[@GrayTrend]

Thanks for the comment! That's messed up that your bulbs didn't come with the reset key. You may be able to use a small paper clip to reset the remote if you need to. Appreciate that you watched the video!!!

[@adelpjetrovic7219]

I had bought one of these and for some reason my remote is not working for the bulb? And recommendations ?

[@GrayTrend]

Thanks for the comment! From the Ecosmart Manual it states: Reset to Factory Setting - Using the wall switch, physically switch ON and OFF 6 times within 5 seconds. The LED bulb will show Red-Green-Blue gradient color and then flash twice after a successful reset. Good luck!!!

[@Bigbankrollxonig]

@@GrayTrendhow do i pair the remote?

[@GrayTrend]

@@Bigbankrollxonig OK, I didn't go over this because I'm not going to purchase additional lightbulbs, but here goes. This is from the Instructions: 1. Turn on the bulb and hold the remote within 2 inches of the LED bulb while it's on. 2. Press and hold the On/Off button on the remote while also (at the same time) pressing the Dimming button on the remote, so press both of these buttons at the same time and wait 3 seconds. An indicator light should start flashing at the top left of the remote. The remote will start searching for the LED bulb. The indicator light will flash rapidly until the LED bulb is detected The light should flash once and the indicator should stay on for 3 seconds, then go out. This indicates the LED bulb and Remote are paired successfully. Hope this helps!!!

[@GrayTrend]

1. Turn on the bulb and hold the remote within 2 inches of the LED bulb while it's on. 2. Press and hold the On/Off button on the remote while also (at the same time) pressing the Dimming button on the remote, so press both of these buttons at the same time and wait 3 seconds. An indicator light should start flashing at the top left of the remote. The remote will start searching for the LED bulb. The indicator light will flash rapidly until the LED bulb is detected The light should flash once and the indicator should stay on for 3 seconds, then go out. This indicates the LED bulb and Remote are paired successfully. Hope this helps!!!

[@danielking.123]

@@GrayTrendhaving trouble getting it to sync :( it randomly stopped working one day

[@stevec5671]

How to pair

[@GrayTrend]

OK, I didn't go over this because I'm not going to purchase additional lightbulbs, but here goes. This is from the Instructions: 1. Turn on the bulb and hold the remote within 2 inches of the LED bulb while it's on. 2. Press and hold the On/Off button on the remote while also (at the same time) pressing the Dimming button on the remote, so press both of these buttons at the same time and wait 3 seconds. An indicator light should start flashing at the top left of the remote. The remote will start searching for the LED bulb. The indicator light will flash rapidly until the LED bulb is detected The light should flash once and the indicator should stay on for 3 seconds, then go out. This indicates the LED bulb and Remote are paired successfully. Hope this helps!!!

[@tribetime321]

Thank you

[@beginnersdaily9007]

can i put this in the globe in my bedroom? hmm emoji

[@GrayTrend]

Thanks for the comment! It's similar in size to a standard light bulb, so it should fit in a standard light fixture. Best of luck to you!

[@rushborda6333]

I lost my remote

[@GrayTrend]

Thanks for the comment! Hope you find your remote soon.

[@jamescostello7584]

I got a problem with this ever since I bought it I screwed a bulb in its just lights up a light blue and the remote does nothing I mean the red light lights on the remote I tried everything to try and reset it but the bulb just stays below and that's it

[@jamescostello7584]

If I unscrew the bulb it will shut off escort back on it just stays light blue and that's it and the remote does nothing to control the ball

[@GrayTrend]

@@jamescostello7584 Sounds like you may have purchased a dud (bad light). I'm not associated with Ecosmart. The best advice I can give you is to contact them via their customer service number 1-877-527-0313. 8 am to 7 pm Monday through Friday. 9 am to 6 pm on Saturday. Best of luck to you!!! Hope you can get this resolved. My light is still out in my lamp post and working fine.