Edge Sealing Multiwall Polycarbonate Sheets

[@jakekeys88music]

I'm building a greenhouse with polycarbonate sheets. Would I be able to tape the edges and then adhere those taped edges with 100% silicone to keep it leakproof? Would I even need the tape if I'm planning to use the silicone? Thanks in advance!

[@BinZiegler]

When using the polycarbonate h channel and u channel for sliding door, how much should we reduce on the width of the polycarbonate pannel so they can fit in?

[@TupmaniaTurning]

Very helpful video - thanks!

[@rickgillis1613]

I would like to say that it doesn't take long (less than 2 years on mine) and the adhesive on the tape lets go.So if the edge is up inside a channel, that's not a big deal but if the edge isn't trapped inside a channel it IMO is then a problem as the open ends are exposed to airflow, insects dust etc.

[@judyselleck2162]

I'm considering using this product in a wall application with the tubes horizontal rather than vertical. What would be the appropriate sealing for the opening?

[@lolavanenburg1647]

What about silicone sealant..I am using the polycarbonate sheet for my aquarium lid..Any suggestions how to use the silicone sealant?

[@ameriluxinternational]

Hello, here is a link to our install guide -> ameriluxinternational.com/wp-content/uploads/2021/pdf-downloads/install-guides/amerilux-multiwall-install-guide.pdf. In the guide, we go over how to use silicone sealant with our material. Let me know if you have any questions, thank you!

[@AjayAjay-gz3oz]

Any suggestions for using Dual Wall Polycarbonate Sheets as the Triangles in a Geodesic Dome.

[@jamesq4451]

Do you have and Installers in the Bradenton FL area?

[@131277stefan]

I'd say the upper part should be able to "breath", using the kind of tape the ladies use to seal the lower end. Water vapor rises!

[@btaos1625]

Droplets would drip down though? Lol..im struggling with all this. Have a greenhouse in boxes still cause Im spun over all the additional things I need to get to go above and beyond the 'picture' instructions from China.

[@lukestone8592]

This is my opinion also...I'm in the process of fitting my roof and I can't decide whether to fit breather tape on both ends?? Otherwise your going to get a build up of condensation as there is no airflow.... I'm unsure what to do?? They all say solid one end only🤔😩

[@131277stefan]

@@lukestone8592 the lower end being breathable means wet air can enter and condensate, leaving spots, in case the panels are cooler than outside air (at night). That's why solar panels (thermal) are best breathable only on top.

[@SanjayKapoorDelhi]

Thanks a lot for this useful video. I am going to use the Polycarbonate Multiwall panels on a vertical wall application. Trying to understand the best way to seal the edges to prevent water seepage and insects etc

[@daviddvorak5805]

Great video! Thanks for making it.

[@silentskystudios]

Hi, can you include a link (Amazon, Ebay, etc.) to the two types of tape used in the video? I'm having trouble finding a vented aluminum tape like you used for the sealing the bottom edge. Thanks!

[@cadetate3023]

I guess im randomly asking but does any of you know of a tool to log back into an Instagram account? I somehow lost the account password. I love any tricks you can give me!

[@bennetttobias6427]

@Cade Tate Instablaster =)

[@cadetate3023]

@Bennett Tobias Thanks for your reply. I got to the site thru google and I'm in the hacking process atm. I see it takes quite some time so I will reply here later when my account password hopefully is recovered.

[@cadetate3023]

@Bennett Tobias It did the trick and I actually got access to my account again. I'm so happy:D Thank you so much you really help me out !

[@bennetttobias6427]

@Cade Tate You are welcome xD

[@amidon422]

Thank you for the informative video i thought it was perfect.

[@trevorjames5493]

What can I put on the one side where the panel meets the brick wall of the next door building besides silicone to seal it is there some kind of tape I can put over top where it meets The Brick?

[@mariemariemarie94]

What did you end up doing? Im very puzzled

[@trevorjames5493]

@@mariemariemarie94 I put silicone along the tiny gap between the side of the first sheet only on the left side where it meets the wall of the next door building then I used something I found on Kijiji for cheap called GAF weather watch leak barrier it's peel and stick for roofing it's around 3 feet wide the roll so I had to cut it to around 6 inches by the length I needed and put it on tight so 4 inch was on the wall and 2 inch on the sheet. It's black so you will see it but the wall is black and I painted the side cap of the sheet black so you don't notice it just looks like a small border but only really see it if you know it's there.. havnt had water come threw or trickle down the wall once yet and we had a few intense rainfalls this not so great summer in Ontario. Lots of wind too but so far so good. It's 90$ at home Depot but you get a huge roll 36" x 50' so I paid 40 on Kijiji for almost full roll. Cut my 6inch by 12 feet and one for backup then re sold the remaining roll for 55 online. Can show photos if you wish. I only needed to do the one wall so it wasn't too hard but if you had multiple spots it still seams doable worked for me so far fingers crossed lol :)

[@2ndamendment-noinfringement]

Thumbs up ladies good job.

[@btaos1625]

Does anyone know..is the u-channel only for the bottom of each panel?

[@junaidcg]

love how she says thumbs up :)

[@nidiatorres2201]

I love her haiir !!!

[@diversitylove5460]

You guys are silly 🙃 I like it

[@home-cookedandhomemade6295]

what size weep holes

[@timmerten6230]

"multiwallpolycarbonatesheet" !! ♥️

[@freehat2722]

Escape not excape. Stand behind the sheet for more visibility. A better mic or fixing audio in editing would also help. I would prioritize these over synchronizing your voices. Hope this helps.

[@Alexxx---101]

Shame it ruins the look though!

[@radarbob9971]

i couldn't hear, women were talking

[@StinkyTeal]

Im supposed believe these women know what they are talki g about?! Get real

[@amidon422]

Obviously you're a professional at spotting someone w/ superiority in the subject of edge sealing poly panels! You are definitely over qualified to put together an instructional video on the subject. Please let us know the link to your video when it's ready 😘.

[@jerrysgarage2593]

@@amidon422 still waiting

[@joanne8946]

StinkyTeal - still waiting! What's taking so long?