MS05l. [Siemens S120 #10] SINAMICS S120 Drive Velocity GearIn

[@1986ah]

Thanks for these demo. This channel is one of the best for plc and drive programming

[@electricalautomation]

Welcome! Thanks for watching!

[@giuseppeBG]

Very interesting course

[@erdaltas1691]

Thank you for video😊😊

[@haoyuyou9465]

博主您好，关于调试图中两个齿轮，让它们两个进行同步，同方向，同转速，除了在您所展示的视频中，在STARTER中有可能实现吗？我用的两伺服直线电机，在尝试同步😀

[@electricalautomation]

STARTER (classic) and StartDrive (new) are two generations of drive engineering software. They are just sofware to configure your drive. The topic discussed in the is video is the S7-1500 Syn motion control topic. Does not matter on which engineering tool you are using. If you are using position synchronization, you'd better using S7-1500 T-CPU for position gear. In addition, STARTER is old, try to use StartDrive

[@haoyuyou9465]

@@electricalautomation Thank you for your reply. As you mentioned, STARTER is just software for configuring the drives, so I don’t need to focus too much on achieving a specific function with it. I have already achieved the positioning function for one motor using STARTER and open-loop movement for the other motor. I am currently learning TwinCAT 3 through video tutorials, and I will soon try to use the motion module in TwinCAT 3 to control the drives and achieve synchronous movement and positioning of the two motors. Perhaps this is possible? I look forward to your response！

[@haoyuyou9465]

@@electricalautomation Because I currently own a BECKHOFF controller, I'll be using a Twincat3.

[@Kozak450]

Can we change the velocity value when the drive is running and the speed will change automaticly?

[@electricalautomation]

Please review this kzbin.info/www/bejne/i523ip-FmpaCm6csi=1Dm2qfRfBtWcv_lL

[@abrahamestradaalvarez9710]

Nice video!! I would like to know what could happen with the slave´s speed if the master has a torque limiting active and a load is aplied until the master stops. I suppose the slave will continue spining since the type of conection is "setpoint".

[@electricalautomation]

Yes, for S7-1500 regular controller, the gear is base on the Velocity 'Setpoint'. But if you are using S7-1500 T Motion Controller, then you can set 'Actual' Gear

[@bhagyodayasinghjadhav]

Great 👍

[@electricalautomation]

Thanks my friend!

[@antokingston8348]

Sir can you please explain about MC Measuring input it will be more helpful for us thank you sir.

[@electricalautomation]

I would recommend reading carefully for this manual cache.industry.siemens.com/dl/files/466/109766466/att_1004383/v1/s71500_s71500t_signal_function_manual_en-US_en-US.pdf note that CAM with Measuring Input always not an easy topic in motion control. Also, find the document about S120 CU Telegram 393.

[@antokingston8348]

@@electricalautomation thank you very much sir

[@antokingston8348]

@@electricalautomation Thank you very much i has one doubt regarding positive and negative edge could you please explain what it means

[@amragwa4005]

Can you make sessions about the cpu with technology I have application with s7-300 with technology and used some function mc_camin mc_camout Mc_camswitch Mc_camclear Mc_sectoradd

[@electricalautomation]

No really, sorry, my friend. I understood this old stuff T-CPU and some Cam motion control. There is less materials for this area and it is rarely used. I would recommend using S7-1500 T and use TIA portal and CAM motion control.

[@amragwa4005]

@@electricalautomationcan you make session for another functions of cpu technology like mc-camin mc-camout and other functions