How to Fix Laptop Broken Hinges Easy and Permanent

[@avp.69]

Two years later and this video is still helping people. Thanks a ton!

[@ElectronicsComputers]

I'm happy to help!

[@WeSpeakFootball]

You just saved me $250 repair, and not even permanent fix thanks

[@ElectronicsComputers]

I'm glad I could help you!

[@rajakhaskheli2948]

250$? Where are you repairing your laptops?

[@erichayes4661]

Of course, if you have a friend that can do it for you, it DOES cost a lot less. Negate the labor charges. And if you're savvy enough to do it yourself, even more than that. If you have the proper tools. A lot of people don't. They don't know what they need.

[@techymomof6873]

Tried this 3 days ago and my hinge is working great so far! **UPDATE 2 weeks, still perfect!

[@ElectronicsComputers]

Nice work!

[@CarloTheImmortal]

Awesome

[@samopp1410]

Is it still going strong techy?

[@mj.alam.]

Mine didn't work for 6hrs..

[@techymomof6873]

@@samopp1410 yes. I've since got a new laptop, but that fix never failed.

[@mwayimchuchu6588]

I wonder why HP never takes their hinge problem seriously.

[@techymomof6873]

Right? My last 2 laptops were HP and both had hinges break through the case. 🤦‍♀️

[@mwayimchuchu6588]

@@techymomof6873 it's a big challenge, I sale brand new electronics in Malawi. Imagine now that each time I have a New HP I have to carefully open it and slightly losen the hinges something I don't enjoy doing given a new computer, but still do just to prolong the hinges life span, especially when I am selling to university students I give them 4years warranty so it's a must to have the hinges issue prevented for me. I have also noted that lately even other brands like Lenovo, (Not ThinkPad) but the basic cheaper Lenovo it's a similar issue partly to do with the cheap plastic casings which can't withstand pressure.

[@techymomof6873]

@@mwayimchuchu6588 I try and be so careful especially since this happened on my last one and it still occurred. I have the Notebook 17 and I don't see any way to adjust the hinge. There aren't nuts on this one.

[@aegiscaleb]

It isn't even just HP, but I have had a lot of issues with them as well. My MSI GE70 MS-1759 just did the same. Idk why they don't stabilize these better

[@mwayimchuchu6588]

@@aegiscaleb probably it's mostly to do with cheap plastic or they need to soften the hinges alittle

[@cbgfojcoam4698]

THIS WORKS!! I just tried it, and I must say, I was willing to spend around $50 to get the hinge fixed. I don't have that little dropper for the baking soda, so I used one of my tiny screw drivers to "shovel" some in place. I already had the super glue and baking soda, so this is just priceless!

[@ElectronicsComputers]

Great job!

[@bonniemunene5163]

Another tip is to put the metallic inserts on the tip of a hot soldering iron and drop them slowly on the plastic casing. The hot insert will sink in the casing as your detach the soldering iron with something a screw driver . You can continue to add super glue or form some plastic around the inserts.This is permanent

[@noaha8915]

If I read this like an hour ago it probably would've saved my hinges which came out... Again. Damn. Thanks for the tip though

[@Godfatherhemanth2369]

No you shouldn't hold the brass holder with soldering for too long or else the stock screws might stick out and the hinge has Lee way break again I over did it and have check if i have small screws length to fit that sht

[@PracticaProphetica]

I've never heard of using baking soda with super glue. Very interesting! What I usually do is drill a hole in the bottom case, where each brass nut is broken loose, and run a small long bolt through the bottom. I put the original brass nut on first, tighten it down a bit, then the hinge on top of that, and another nut on top of the hinge.

[@ElectronicsComputers]

Great tip!

[@modernisingyourretrocomput3866]

Four years after this was uploaded, I’ve tried this repair method on a Dell Vostro 3360 and it worked perfectly - thank you!

[@ElectronicsComputers]

Glad it helped

[@technomad900]

Awesome Video , another tip, loosen the the hinges slightly . In my experience hinges are often too tight, which could be part of the issue in the first instance . About half a turn with a nut spinner ( M5/M5.5/M6 too hard with plyers ) each end of the hinges . Also Silicone grease or 3 in 1 oil helps

[@ElectronicsComputers]

Thank you for the comment!

[@violette8715]

Indeed too tight! I'm fixing a laptop I had when I was younger and I remember the screw being so tight I couldn't unscrew it to replace the screen so I think I just tore the arm of the hinge off and then tore off the broke screen (god forbid I told my parents either)because I was like "better to be able to use it than close it" like no that's so impractical

[@chrisgraham2904]

Yes, the hinge tension adjustment nut seems to automatically tighten with use as the screen in lifted and closed. Loosen the adjustment nut until the hinge moves smoothly, but will still support the screen in the open position. A drop of Locktite thread locking solution on the adjusted nut will prevent the nut from automatically tightening in the future. Very careful application of a lubricant will aid the hinge's movement and it can be applied to any areas that you don't want to be adhered by the crazy glue or epoxy that you use for the hinge attachment.

[@niko1even]

Thank you so much, I currently own an MSI GS75 Stealth, and I’ve heard of MSI laptop hinges having problems, so I’m preparing myself just in case something like this happens.

[@ElectronicsComputers]

This is the best solution apart from replacing the case

[@alloycrow917]

Yes, this is true, My MSI Modern has this problem, I will use 2 part epoxy to fix it, Right now don't have the time to have my computer down. Maybe newt week once I'm done with some design projects.

[@kjetil442]

what container did you use for the baking soda?

[@haadig7438]

I also don't understand

[@erichayes4661]

I have tried cyanoacrylate to re-set hinge anchor points. But actually gorilla weld or jb weld has worked best, if you put the mix in a 20ml oral dispensing syringe after mixing, you can use micro-control to build up your anchor points after you have placed them. I usually use a mobile-fixable desk-mounted lighted magnifying glass and tweezers as well to get the fit and finish right. The one thing I noticed that you didn't do, was remove the circuit board away from the affected area and reinstall them later. I always remove the circuit boards so that in case I make a mistake, they won't be damaged or accidently glued in place in case another tech needs to work on it in the future for some other issue.

[@ElectronicsComputers]

The client was waiting for that laptop and I was trying to make that video as quick as possible, this is why I didn't remove that board.

[@challengegravity]

Thank you so much! I had been researching what kinds of epoxy/putty to use, because I couldn't find any guides on how to fix the plastic webbing online... it was just guides on replacing the metal hinge or the whole case/chassis. But then I saw your thumbnail with my exact problem, and I had no idea about adding baking soda. Many thanks!

[@ElectronicsComputers]

Glad I could help!

[@trikto9120]

Thanks a lot. I repaired my laptop's hinges with the help of your video. Now it works fine.

[@ElectronicsComputers]

Glad it helped

[@stephenjwan]

By far the most down-to-earth and clear-as-day explanation...kudos friend!

[@ElectronicsComputers]

Thank you for the comment!

[@年ONAME]

Thanks, this works. For beginners suggest you cover the screw threads with tape first!

[@ElectronicsComputers]

I'm happy to help!

[@inconspicuous-nobody]

Oh man, I'm going to remember this for next time. This is absolutely ingenious.

[@ElectronicsComputers]

That's the best solution I've seen so far.

[@alembicbassman]

I used the bolt through technique 4 x M2.5 x10mm on my G3 255 Secured with a nut on the back if the screen case. There was nothing left of the plastic cups to put the brass inserts into. Rock solid and will not snap off - not bothered what it looks like - laptop is 8 years old anyway.

[@ElectronicsComputers]

Good job!

[@albatros232chimoio3]

Man, you're a fuxxing genius .... I fixed my pc with this method .... I don't know how much it will hold up because it was the first time I did it and maybe I could equip myself a little better even to better distribute the bicarbonate ...... but the result was crazy. .... when it dries it becomes almost duller than epoxy glue ..... I also softened the hinges a little to make them do less resistance and consequently less leverage on the repaired part .... THANKS for your sharing .....

[@nsovosikhalela6345]

It actually works! Thanks a million, I've saved so much money and my laptop works good as new

[@ElectronicsComputers]

You're welcome!

[@darkstarrone8764]

Thanka for sharing, i fix a lot of laptops and have been using epoxy for hinges with mixed results. Will try this method. Si there any curing time?

[@ElectronicsComputers]

I'm happy to help! I've fixed dozens of laptops with this method with 3 month guarantee and never had any problems. This method gives you an instant result. The glue compound becomes rock-solid almost instantly.

[@darkstarrone8764]

@@ElectronicsComputers Nice! Thanks for the quick reply! I have 3 laptops for resale with broken hinges, will try it tonight!

[@darkstarrone8764]

@@ElectronicsComputers update: Just finished repairing a laptop with broken hinges on both ends (5 patches total), wow! That patch is ROCK SOLID!!!! I used a kids tylenol seringe to spread the baking soda, i was initially pushing the end to make the powder come out but after a few patch i realized I could simply tap the syringe against the spot needing the patch and it was much more precise. I found it easier to do it in small layers (2-3 layers), but overall wow I am so satisfied with this method, i could screw in the screws super thight and it would not budge! 10/10 method Fun fact: The laptop I was repairing had a failed epoxy repair... lol Thanks again for taking the time to make this video!

[@jaimematos6457]

@@darkstarrone8764 Thank you very much for bringing back this feedback from your experience! Really appreciate it. My laptop was fixed with Epoxy on metal hinge to plastic and it lasted for 3-4 years, now broke again but it's way more broken than before

[@jeancpt]

I do this often. I find that if you scoop the powder into a straw, hold it over the spot where you need powder, rotate it slightly, it is more acurate and not so messy.

[@ElectronicsComputers]

Thank you for the comment!

[@chrisharkin3741]

Thanks. This was very helpful. I was able to repair my partner's Lenovo laptop with the bad hinge design which tightens over time. The superglue and bicarb soda worked so well, it is amazing. Don't forget to adjust the hinge tension - some hinges get tighter as they age, which puts excessive force on the surrounding plastics. I also added a little lubrication to the hinge. So far, so good...

[@ElectronicsComputers]

Glad it helped

[@HishaMized]

Thanks! I used Araldite's All Purpose Epoxy Adhesive ( resin + hardener) instead and then followed thr steps as mentioned in this video. It fixed the hinge. The official HP service centre was charging 80 Dollars for the same task.

[@ElectronicsComputers]

Nice work!

[@ndreiu4588]

Works wonders! I must add that you should also oil up or use WD-40 on the hinge mechanism to loosen it up/put less strain on the new hinges.

[@ElectronicsComputers]

Yeah, but it's better to use a sewing machine oil or gun oil. WD-40 won't last long it evaporates pretty quickly.

[@maven.osijek]

This video is priceless! Thank You! Don't know how I didn't think of this myself!

[@ElectronicsComputers]

Thank you for the comment!

[@sanashy9024]

I just saved $40 dollars for repair. Thanks to this!

[@ElectronicsComputers]

I'm glad I could help you!

[@vyspeeds]

ONLY 40? lol I keep being told it is a $300 repair smh

[@simonm8586]

@@Gsityoass Every laptop is different. I just spent 1.5 hours disassembling an extremely difficult laptop. So many cables, keyboard, hdd, battery, fan, subframe...

[@hazemtawfik556]

Congratulation for this very well produced video; the image is of a high resolution and the narration is well written. Although I am very handy and can repair many things; I was not aware of the strength of mixing super glue with baking soda. I tried this on a broken hing of an ASUS laptop and the result was amazing.

[@ElectronicsComputers]

Glad you enjoyed it!

[@wotspotgaming]

Oh I totally agree

[@wotspotgaming]

@@ElectronicsComputers great work sir

[@buckfiden2959]

I've had several laptops break hinges. I fixed one with epoxy and it broke again in a few months. My new laptop(HP Envy 17") is broke now too. I'll try this method. I also will put some lubricant of the hinge as well. I think with age the hinge gets harder to move and the increased torque damages the hinge. A little light grease might be all it needs...

[@ElectronicsComputers]

Epoxy is not the best solution for that problem but superglue + baking soda makes super hard compound which is virtually unbreakable.

[@mohamadzayat6122]

Bro I got my dell g3 new laptop 3 months ago, and now I'm having this bullshit problem, thanks for the method, gonna try it today and see how it goes, thanks a lot.

[@ElectronicsComputers]

It will definitely work just do it right and be extremely careful with the brass inserts.

[@mohamadzayat6122]

@@ElectronicsComputers actually it did work thank you very much, also id like to suggest a minor change, for those who dont have the baking soda you can replace it with the burned parts of a cigarette, it forms a super structure that holds just as strong, best of regards.

[@anshumanpathak1448]

@@mohamadzayat6122 this means I've to smoke the frickin cigarette first, huh, there's first time for everything, am gonna do it. Thanks anyway.

[@mohamadzayat6122]

@@anshumanpathak1448 i took a couple from my smoking friend and made it work :D

[@Infiniti25]

@@mohamadzayat6122 I presume you mean the filter tab?

[@7thvillain236]

Thank you very much!! Mine is broken both the hinges and I finished the right one (but tried to open it lmao) and damn it works great, feels like new!

[@ElectronicsComputers]

I'm glad I could help you! I've been using this method for about 10 years now and all my customers were very satisfied and none of then came back with the same problem.

[@SandraWamaitha]

Hey 👋 thank you so much, I did it and it worked. You just saved me 45$ of repair

[@ElectronicsComputers]

Glad I could help

[@francomagrini3120]

Awesome! I have ZERO skills for this stuff, still it worked great. Great enough to have me here recomending this option I must add =) Thank you!

[@ElectronicsComputers]

Glad I could help!

[@CarloTheImmortal]

Pretty cool idea thank you. Seems a tad more cumbersome on the lcd cover screw mounts given the limited space. I usually loosen the hinges a bit since theyre often the source of the problem (hp toshiba lenovo... what a nightmare)

[@ElectronicsComputers]

lenovo uses some cheap crappy plastic which brakes with minimum force and with age it becomes even more fragile.

[@CarloTheImmortal]

@@ElectronicsComputers yeah pretty disappointing. Btw i forgot to ask what do you call that baking soda dispenser? Id like to get one to attempt this on a stupid 17 inch hp lcd cover... i even unscrewed the things slowly with as light pressure as possible but they still cracked

[@ElectronicsComputers]

@@CarloTheImmortal You can use a new syringe without a needle filled up with a backing soda. Just slightly shake it or knock on it for the backing soda to come out. In my case I was using a container from some medicines or something.

[@CarloTheImmortal]

@@ElectronicsComputers awesome thank you dude that helps enough to look at containers or options cause ive had this damn thing sitting here too long the lcd cover replacements like 80 dollars

[@r.upendran446]

Unga videos romba use full ah irukku irundhalum oru doubt clear pannunga Hinges thread illa fix pandradhukku ulla brass holders kuda illa na enna pandradhu nu oru video podunga

[@DanYT92]

Usen resina + pegamento, el combo que venden en ferreterías. Ese pega el plástico y para partirse hay que darle tremenda presión. Pega 10 veces más que un pegaloca o pegatodo, pero se requiere 24 horas para que pegue completamente.

[@afiqkhusairi2452]

I did it and failed the first time. It took me about 3 hour to scrape back the glue using alcohol. Although it not perfect. I tried the 2nd time and worked nicely. The laptop now has a bit bulge because i cannot fully close but the hinge is repaired. Thank you.

[@afiqkhusairi2452]

Be careful when applying the glue because some laptop has a really small space between the back panel and the mobo. But it is good to learn even u are first time like me. Definitely recommended.

[@ElectronicsComputers]

You can cut or file down the excess of the glue.

[@afiqkhusairi2452]

@@ElectronicsComputers thanks for the tips

[@santhanabalanv7624]

​@@ElectronicsComputersHow to exactly??

[@santhanabalanv7624]

I fixed mine but the height of screws is a bit high such that the casing cannot be closed! Now I need to scrap off the whole thing? The nuts are glued to a metal base

[@lolboy-642]

this is exactly what i was looking for. thank you for the upload

[@ElectronicsComputers]

Glad I could help

[@wotspotgaming]

Me too XD

[@wotspotgaming]

@@ElectronicsComputers 🙏

[@tshiamomongwegi2470]

great video man one question which model hp is that ?

[@ElectronicsComputers]

Thanks! It's HP 15-bs576

[@moonzoom5134]

Great video. I was so surprised to see that the laptop you were fixing was the same model I own 0: . I guess this particular model gets broken hinges commonly. Thank you for sharing the secret ingredient baking soda with us. Found this video extremely helpful.

[@ElectronicsComputers]

I'm glad I could help!

[@ThisEveinEvening]

It's the black plastic part surrounding the brass inserts that broke into tiny pieces and I can't put it back together. Some of it is gone. What would you suggest? Edit: Oh I replayed it and heard you say it's okay not to have the plastic part and to just glue the brass inserts on? Edit: I found the same question that you answered. Thank you so much. You're a lifesaver! (My laptop is pretty much the breadwinner).

[@marekbohunsky9959]

perfect, didn't believed that this mix will be so rock solid and hard, it really helps and works, thanks a lot for your tutorial!!

[@ElectronicsComputers]

You're welcome!

[@InUkrMade]

I've applied the same solution for my ASUS FX504 and to avoid the getting clue inside I inserted bolts into the nuts a little bit.

[@ElectronicsComputers]

I hope it worked for you.

[@amateurpro1185]

Hey bro I got the fx504 and my hinges are broken as well. Did you fix it?

[@Thankonomics]

Same my asus fx505 broken bolt

[@gthing2264]

My FX504GM is having this issue. I'm thinking good quality epoxy resin would be a better option?

[@amateurpro1185]

@@gthing2264 i fixed mine using high epoxy glue and it broke again.

[@vic9591]

It works as magic!! Thank you so much. Just be careful because the mix of super glue and baking soda gets hard very fast! I have not been able to gather the plastic bits because they were many and very small so I rebuilt the plastic cylinders where the screws go with the mixture of super glue and baking soda and there have been no problems =)

[@ElectronicsComputers]

Great job!

[@jcr65566]

Thank you so much for posting this. Weeks ago We got a Toshiba satellite lap top off of eBay. for my wife. I know it had broken hingers and thought it be OK when we got it. it was not that bad But as she use it it got progressively worse. to the point i was all most unusable But watching your video I was able to repair it with the superglue and baking soda it works find now like new

[@ElectronicsComputers]

I'm glad I could help you!

[@jamiehearn6583]

I used this hack with my laptop in October 2021. Now in 2023, 20 months later, it finally gave out. I'm gonna try to fix it again the same way, but I think an extra 20 months with my laptop was great either way.

[@ElectronicsComputers]

Great job! Next time, try to apply more compound around the mounting area or where it broke again. And don't forget to degrease that area.

[@haroldseven8675]

nice video, tks for sharing. 2:41 -> any tip for not glue the board too?

[@ElectronicsComputers]

Remove the board before applying the glue.

[@haroldseven8675]

@@ElectronicsComputers Tks for fast answering. I m asking cause I had similar problem and when I made without the board, the glue entered on the board space and it is very hard to remove the glue mix after it dries in this small space. Anyways tks for your answer, very apreciated

[@ElectronicsComputers]

@@haroldseven8675 You can cut and remove the excess compound with a utility knife.

[@RISVANHERIYANTO]

Thanks for sharing your knowledge bro.. very useful. Usually my friend told me for using sand, and glue. But always cracked when I try to open the laptop. Will try ur method this time.

[@ElectronicsComputers]

I've been fixing laptops with this method over 10 years and none of my customers came back with the same issue.

[@miko3783]

@@ElectronicsComputers maybe because they go to other repair service LOL.

[@ElectronicsComputers]

@@miko3783 Nope! Some of them come with another problems and devices.

[@miko3783]

@@ElectronicsComputers okay might try this but why baking soda? Instead of iron powder?

[@cuakman]

@@miko3783 Baking soda makes glue solid, insta dries the glue and adds volume. I've been using this same method for arround 4 years too and never had a problem.

[@Damalycus]

I've used this trick for a lot of years, for my own laptop is fine, but for clients computers I just use 2 part epoxy. Harder to affix it in place, because it takes time to cure, but afterwards is near indestructible. One of my heavier media laptops has metal parts broken break apart after years of use, so no epoxy or superglue can help - there I just DRILLED TROUGH the laptop body, and put a steel plate on the other side. Looks ugly but it works. Because design allows for it to work. In newer slimmer laptops the plate and end of screws would cut into screen when fully closed.

[@kennyzhang9942]

How can I determine the size of the brass inserts my computer has (It's an acer nitro 5).

[@FreeStockPromotions]

You figure it out I have the same computer problem?

[@erichayes4661]

Most of the time you can retrieve your own brass inserts. From the broken hinges. Just use a pair of needle nose pliers and a small phillip head screwdriver. But I do remember he did put a link in the description below where you can get your own. Unfortunately, they seem to be from Alibaba, its not too easy to get product from them nowadays. Look up "laptop brass inserts" on amazon. Might be a LOT quicker, since everything coming from China nowadays seems to take at least 3 weeks.

[@elecpaunch2718]

At around 3:00, did you just drop water or is it a different substance such as vinegar?

[@ElectronicsComputers]

That was superglue. All you need is a regular backing soda and liquid superglue which is based on cyanoacrylate.

[@SpaceT3]

Thanks for this tutorial, I can fix my 15 years old Aspire 4741. That thing hinge finally gave up and snap off because I accidentally let it turn on inside a locker that cause it over heat, and you know what happen if a plastic get too hot

[@ElectronicsComputers]

I'm glad I could help you.

[@orenatan]

How long do you wait before you screw in the screws?

[@ElectronicsComputers]

Wait for about 20 minutes until the compound hardens enough.

[@anthonyjapitana9852]

I have a problem right now when it comes to that hinge.. May I ask what should I buy for the sizes of the brass insert for MSI Modern 14.

[@crashmusketeer306]

The hinges may have the screw/insert size printed/etched on them.

[@meetpatel7564]

I was planning to buy a whole new body for my laptop that has the hinge broken and lifting. I am going to try this and I hope it works out. Problem is my screws are gone and I have no way of finding out which ones they were so I cam buy to fit in.

[@CoMmAnDrX]

Another method I use is pushing the brass inserts deeper with a little heat from a soldering iron. Also I've been using UV Glue to buildup around the mounts.

[@ElectronicsComputers]

Great tip!

[@kadiravelshanmugavel8925]

Thank you I followed as you said and repaired my laptop by myself. thank you very much.

[@ElectronicsComputers]

Happy to help!

[@talalzahid84]

When the plastic gets old then nothing works it breaks again and again

[@ApostKef]

is the baking soda combined with glue dangerous if it sits on top of pcb?? (not in crucial part of course). The standoff is very near in a pcb, so the baking soda has to sit on top of the pcb, otherwise i cant build the "baking soda wall". Also, is epoxy glue a better solution for these kind of plastics?

[@ElectronicsComputers]

Epoxy is not gonna work for that particular application. We've fixed hundreds of laptops in our repair shop with this methods and none of those clients returned back with the same defect. Once the compound is hardened you can cut it with a utility knife to remove its excess. Nothing will happened if you apply it to the PCB too.

[@Trust_but_Verify]

I think work in ventilated area to prevent inhaling too much Cyanoacrylate.

[@yamawwad]

Could you please make a video on keyboard replacement of DELL inspiron 3793 , thank you.

[@little.3870]

THIS!!!

[@seamusmcgarvey8479]

Hi! What is thread size and length you used? If it matters I have an Acer Nitro 5

[@ewezungim6541]

Did u disassemble the base of the laptop? And when do u disassemble the top?

[@ewezungim6541]

Do u all hp laptops have their hinges at the base? I'm not exactly sure where mine is

[@ElectronicsComputers]

All models have different construction. I have a disassembly video for this particular model if you need it.

[@ewezungim6541]

@@ElectronicsComputers Thanks

[@Ad-gc7th]

Hi there. Your way is brilliant. But you know the place where the standoff is placed? What if the plastic wall of the standoff is broken off and lost. Any idea how to fix that? Or make a new wall?

[@ElectronicsComputers]

With that compound you can make a new one and after it hardens you can cut it drill or sand to give it any shape you want.

[@Ad-gc7th]

@@ElectronicsComputers thanks so much bro for your response.

[@keletsonoimer8665]

Good day sir. What size are the for the brass? I'm having the same laptop as the one on the video

[@crashmusketeer306]

The hinges may have the screw/insert size printed/etched on them.

[@isshinn-i4j]

What brass insert kit to buy? I have a HP Probook 430 g2 and I need just 5 of them.

[@crashmusketeer306]

If it's for the hinges, the hinges themselves may say.

[@QuentacosIsMe]

How long does the baking soda take to dry?

[@ElectronicsComputers]

Just a few minutes and you're good to go.

[@greatvedas]

very interesting. How does baking soda help.

[@ElectronicsComputers]

It reacts with cyanoacrylate and forms strong unbreakable compound.

[@jurnyrzezaniec5631]

So, what if all of the plastic has broken off and fell out? Do I have to reconstruct whole thing with glue and soda?

[@ElectronicsComputers]

Yes, that's right. You can give it a proper shape and then cut, sand, drill or whatever you want.

[@melisazenelaj3881]

I have the exact laptop and my problem with the hinge it's not that when I open it doesn't pull the bottom side where the keyboards are, alongside the laptop screen it takes out the plastic thing around it, not sure if my hinge is broken like yours.

[@ElectronicsComputers]

My method will definitely solve your problem.

[@jasongrenier3590]

@@ElectronicsComputers My son's HP laptop is doing the same thing around the laptop screen. So I will try this method this weekend. I offered to buy a new one but he is in his senior year and wants this to last rest of the school year cause I promised him a really nice laptop when he graduates.

[@ElectronicsComputers]

@@jasongrenier3590 It will definitely help just follow my instructions.

[@MuhammadZahid-tf1vz]

Sir Would u like to guide which material has used. 1. Which whit material 2. Which proxy

[@ElectronicsComputers]

Don't use epoxy! All you need is a regular liquid superglue and a regular backing soda.

[@shawnm2355]

So much thank you!!!!!!! I can't express my gratitude in words......thank you for the baking soda technique... I'll now try it...❤❤❤

[@SteveHart]

Do you find superglue/baking soda is stronger and longer lasting than epoxy?

[@ElectronicsComputers]

With superglue and baking soda you get a rock-solid compound which is harder than epoxy and will last longer

[@SteveHart]

@@ElectronicsComputers thanks, I will give it a try. I've always used epoxy for work like this one.

[@gonzalosaez1689]

saludos! that powder is baking soda?

[@ElectronicsComputers]

Yes, correct

[@f9408]

@@ElectronicsComputers can i use other than baking soda?

[@wukki99]

thank you very very much from Korea. i'm gonna do this tommorrow.

[@ElectronicsComputers]

Best of luck!

[@kennedymcdon3674]

What size brass inserts do laptops use?

[@crashmusketeer306]

The hinges may have the screw/insert size printed/etched on them.

[@muhammadsaleemkhan5761]

thanks nice video, just want to ask to repair this kind of stuff on dell laptop inspiroon 5000 14 inch, do i have to disconnect battery cable?any other thing that i need to remove/disconnect before fixing this mounting screw holder. i am new to repair. thannks

[@ElectronicsComputers]

Id recommend disconnecting the battery before you start working inside your computer, because you can drop some screws or a tool on the PCB and it will shirt some components which will make your problem even worse.

[@muhammadsaleemkhan5761]

@@ElectronicsComputers thanks for your prompt reply. sure will do. just to confirm should i remove the battery or just disconnect the battery cable? is there any other cable i need to disconnect before repairing the screw mount for hindge for dell inspiroon 14 inch laptop? can i use Elfy Super Glue with baking soda? or i need specific super glue?

[@moskito2010]

Hi love your Video the link to the glue does not exist can you Repost the link to the special glue?

[@ElectronicsComputers]

Fixed! Thanks for notifying me.

[@moskito2010]

@@ElectronicsComputers i must ask again just i need only the glue or need the Power to "aktivate" the glue fixing?

[@ElectronicsComputers]

@@moskito2010 You'll need to buy superglue and regular backing soda which is available in any grocery store.

[@laurechaelie6890]

Please help, what size hinges nuts you use and how do I fix my hinges laptop that is broken from the hinge body/arm?

[@ElectronicsComputers]

The link for the brass inserts is under that video. Their size depends on the screws

[@laurechaelie6890]

@@ElectronicsComputers my hinges says m2x3 and the hinge arm is broken off. Do you have any hinges with arm links for a hp pavilion x360 - 14m- cd0001dx Please ? You are really helping me 🙌

[@Kevinaya]

Hey bro I also have the exact laptop and I fixed it this way and it's look good my question is this won't like decay or break like every month right? On average how much time will this hold

[@gamerblondie28twitch58]

Posting a second comment for those who want to try this and have no other options. My attempt is finding to be more difficult considering I do not have ANY plastic pieces able to hold the little gold thread pieces. At first I tried directly just gluing the pieces to the plastic. Let that sit for an hour or so, but when testing out to see if the screws at least stayed in, they came right off. A second attempt was made with the baking soda method, thinking it was going to dry quicker and harder. Same result. Both the gold thread and the screw came right off after I let that sit about another hour. It is a messy process to try and clean this up. Its going to take time now to make sure to get all the glue and baking soda off the plastic of the laptop for a flush fit, but I will try again and let it set and CURE for even longer (24 hours recommended) HONEST OPINION (so far): if there is no plastic pieces to set the threads in, attempt at your own risk. It seems more of a hassle to try and clean it up if you do not get it right the first time. Be very thorough and make sure the gold threads are aligned properly as well as you let it dry/cure FULLY if you do either method for 24 hours!!! I am going to clean it up and try it again.. hoping it will bond properly 🙏

[@ElectronicsComputers]

What glue did you use?

[@gamerblondie28twitch58]

@@ElectronicsComputers all I had was Gorilla Glue. I am redoing it and put a little bit on the gold threads to hold them in place until they're cured. Then I am going to do the baking soda method over them to keep them more sturdy and let it cure for a full 24 hours. Hopefully it works lol

[@ElectronicsComputers]

@@gamerblondie28twitch58 It will never work with Gorilla glue because that glue is made of polyurethane. You need a regular super glue or Gorilla super glue that is made of cyanoacrylate.

[@gamerblondie28twitch58]

@@ElectronicsComputers damnit 😔 I guess I will try to scrape it off...

[@gamerblondie28twitch58]

@@ElectronicsComputers let me double check to see which one I have used...

[@mandyscisco]

Would it be okay to use gel superglue instead of liquid superglue?

[@ElectronicsComputers]

It should be a liquid one otherwise it's not gonna work.

[@mandyscisco]

Thank you so much for the fast reply.

[@radekcegla2351]

Great video !!! what is this powder?

[@ElectronicsComputers]

It's a regular backing soda.

[@dkdude]

awesome, thanks! mate, how could I fix a broeken (in two) braket. I don'y what material it is, but Im pretty sure the compound is similar to all laptops. thanks!

[@ElectronicsComputers]

I'm happy to help!

[@aaronlascota5143]

may I know what is the actual size of brass insert is for laptop hinges please? very big thanks.👍🙂

[@crashmusketeer306]

The hinges may have the screw/insert size printed/etched on them.

[@testgoogle4395]

@Electronics&Computers will it still work on other super glue brands? like mighty bond etc...

[@ElectronicsComputers]

You can use any super glue based on cyanoacrylate

[@FaustRSI]

Is there any difference between "baking" soda and just a regular soda ( Na2CO3)? Or by baking soda you mean Sodium bicarbonate with the formula NaHCO3?

[@ElectronicsComputers]

Backing soda has slightly different formula: NaHCO3. You can buy it any grocery store.

[@RKStudio6]

Sir I need this dust . Please provide me link .

[@ElectronicsComputers]

It's just a regular backing soda. You can buy in any grocery store or go check your kitchen.

[@martiniliev35]

One of the hinges of my Asus FX505 sits a bit higher after closing, so I always press it down completely. Yesterday it I heard a pop as if something snapped in there, so this video might come in handy sooner or later

[@ElectronicsComputers]

I've been using this method in my repair shop for many years, and I haven't had a single return within the 3-month warranty period for this job. HP and Asus laptops are prone to hinge issues, but this method reliably fixes them.

[@safouenelemsi6119]

thank you very much man , you're a genius

[@ElectronicsComputers]

I'm glad I could help you!

[@theverycutecat4812]

I work for laptop repair shop years ago. No body know this trick yet. Wish I know this earlier, so can fix my now dead dell latitude..

[@amirjan175]

Yea this became a problem for me and i stopped cleaning my laptop because i found out that the screws cant be tightened again if i loose it one more time

[@pauldeguzman8778]

Hi! Does it take hours or minutes only before I open the laptop after fixing thr hinge?

[@ElectronicsComputers]

Wait for about 30 minutes.

[@alp1791]

Great video. I have a question, My hinge broke once already and i used epoxy to fix once, it lasted 2 years but now it broke again. my problem now is that im missing both the brass inserts and the plastic rings that go around those brass inserts. what can i do to make new anchors for the screws?

[@ElectronicsComputers]

Plastic rings is not that important just buy a new brass inserts. The link in the description.

[@mehmets.6124]

i am using this combination (super glue + baking soda) for my daily repair issues at home and it works in any circumstances on any objects. But this time i need to use them for my MSI Laptop hinges

[@ElectronicsComputers]

It's the strongest stuff as of today. I haven't seen any glue or epoxy that is stronger that baking soda with cyanoacrylate.

[@engagedwithmusic3420]

Can i use some kind of an oil to the hinge? Before my laptop hinge broke its already heavy to close anf open, so i'm worried that it might just broke again if i fix it using your method

[@ElectronicsComputers]

You can add a little WD40 or some oil to slightly lubricate the hinges but only if they are really tight.

[@Infiniti25]

I would use WD-40 to clean - it doesn't lubricate. Then I'd apply some lithium grease, or if you want to use oil go with sewing machine oil.

[@laurentiuilina4992]

Hello! What kind of glue you ușe?

[@ElectronicsComputers]

You can use any liquid super glue based on Cyanoacrylate. The link in the description.

[@_deathcry]

Great video, sad that hadn't thought about this one myself, but I have fixed some other things with this method and I must say that things that need some elasticity or have high/frequent stress are cracking this composite quite fast, like in a month or two. But overall that is so stupid that those high stress areas are so often made of cheap plastic that lasts just enough to get you through warranty period of the device. Like even my MSI laptop I bought 3 years ago for like 1900 euros started falling apart half a year ago, so I had to buy a new front panel for another 120 euros. Thats considering the fact that I was closing the laptop only once a week and it was mostly stationary device.

[@ElectronicsComputers]

Sometimes, I think that laptop manufacturers deliberately make those areas weak. Lenovo, HP, and Asus have the weakest hinge mount area.

[@_deathcry]

@@ElectronicsComputers Probably, and like they are certainly able to increase the durability of the mount area by making it bigger and having more than 3 screws, so that the applied stress would be distributed more and thus chassis last significantly longer, but those big companies probably don't need long lasting product, neither they care about E-Waste, because who would buy new laptops then...

[@Tuatara1989]

Yes it's baffling. If I'd ever buy a laptop I'd look for some videos to see what the hinge mounting is like. Seen this happen on too many of them already.,

[@bizzhat]

aweeesome. just what I need, a huge thanks! man.. i just wish my hands wouldnt shiver as much as they do :/

[@ElectronicsComputers]

You can do it!

[@bizzhat]

@@ElectronicsComputers thanks yo ^_^ worked like a charm, hinges are fixed! ..although I superglued the power-button during the fix D: (raaaage!)

[@sierraarmstrong4111]

J.B weld also works great!

[@ElectronicsComputers]

Yes, J.B. Weld is great stuff, but it's not perfect for that particular application. Cyanoacrylate has low viscosity, which allows it to get inside tiny cracks between plastic parts and the brass insert. On the other hand, J.B. Weld will only create a strong bond on the surface, leaving the inside structure compromised and likely to fail again in the future. For the past 15 years, we've had ZERO returns during the warranty period using cyanoacrylate and adhesive filler.

[@RealSoloShow]

What's the name of that round part below the hinge that makes the laptop screen to face down or up?

[@ElectronicsComputers]

You mean where the screws go? Those are brass inserts, the link in the description.