That's why the MOSFETS are getting burned - A pretty cool experiment

  Рет қаралды 37,876

Electronics Repair School

Electronics Repair School

Күн бұрын

Пікірлер: 104
@andrewwturner
@andrewwturner Жыл бұрын
That's a great and easily understood example of thermal runaway (up to the point that protection kicked in and shut it all down).
@electronicsrepairschool
@electronicsrepairschool Жыл бұрын
Oh yes, that was the word which i was looking for, 'thermal runaway', yes indeed this is a clear example of thermal runaway
@jurgenkruger3932
@jurgenkruger3932 4 ай бұрын
The thermal runaway is a semiconductor issue. A self-amplifying problem which can be faced only by proper thermal protection and cooling system. Sometimes the one or the other fail... The CPU and GPU have a thermal shutdown protection implemented. So they do not die on a primary impact. On a primary impact, a MOSFET get killed. Mostly MOSFETs without an implemented over-temperature or over-current protection. Secondly, this will kill then the Dr-MOS and/or the CPU/GPU.
@oefzdegoeggl
@oefzdegoeggl Жыл бұрын
well, replacing the thermal paste every 3 months is maybe a bit often ... but a good regular dust removal will never hurt
@jonnward9555
@jonnward9555 Жыл бұрын
i have watch hours of your videos , your shearing of knowledge is a spiritual thing , in my country of new zealand . i would just like to express my thanks ,
@DevilbyMoonlight
@DevilbyMoonlight Жыл бұрын
Spot on Sorin, there is something else, I've seen heatsink paste put on the wrong way too many times, too thick an application causes trouble not only with it being sub optimal performance, but it can make it dry out prematurely or even 'pump out' with many heating and cooling cycles, many people see this and mistake it for the paste being too thin, when in fact its because of expansion and contraction during the heating and cooling process, manufacturers do a 'good enough job to last the length of warrantee and a little bit more' to avoid a warrantee repair but end users with a bit of care can do better, the paste is there to fill in imperfections in the mating surfaces only, its not meant to have a thick blob in the middle like a sandwich where the mating surfaces dont actually touch, if you do it right - you wont see temps increase over the course of a few months or even years if you keep your coolers clean, I have not needed to replace mine in my laptop as yet, its still running the factory goop, but temps stay well in the safe zone and the keyboard doesnt get too warm, even though it gets used every day (MSI GE73 i7 8750h/GTX1060 32gb of ram 2x nvme +1 SATA SSD) and had it over a year before the pandemic and it sees some heavy gaming use in Star Citizen, I do use my own fan profileand throttlestop to undervolt and manage the heat the 8750h pushes out when gaming in the summer, in real terms it feels smoother as there is no ramp up or down, it is overdue for a change though but I dont like the current options out there.
@1syncgg
@1syncgg Жыл бұрын
honeywell PTM 7950 thermal pad eliminates the pump out problem, I believe even lenovo uses a custom version of it called PTM 7958 thermal pad version.
@sunstart
@sunstart Жыл бұрын
I love how you explained everything in detail I envisioned everything you said in my mind. I didn't even know that thanks.
@georgeindestructible
@georgeindestructible Жыл бұрын
A modern CPU will attempt to lower its voltage to frequency curve until it can no longer do so, then it will attempt shutdown, but if an external source keeps heating it or keeping it heated, especially more than it can handle (working or not) within a certain time limit (based on the material's thermal limits), it can still fail regardless, a saturated heatsink can cause that, unless the heat is getting away faster than the max amount of heat the heatsink can dissipate in time before being saturated and before the cooled component fails as well, which is when it needs active cooling. This video illustrates this perfectly.
@hssnov
@hssnov Жыл бұрын
I usually put thermal pads everywhere because i don't like the components to get hot. Hot means less life. Redesigning the motherboard with 3d printer and make new Copper heat sink it the best way.
@retrocomputinggrotto
@retrocomputinggrotto Жыл бұрын
Great demonstration about overheating - very well explained.
@inventorOz84
@inventorOz84 Жыл бұрын
This is proper education!
@wanchonarbonavalle741
@wanchonarbonavalle741 Жыл бұрын
Great explication Sorin! I've got a Fujitsu Siemens laptop 17 years ago. It's work now because i always used with a cool pad. The thermal fans never enough for me
@magicmike7791
@magicmike7791 Жыл бұрын
Well that s one reason, and because it s built to last for 20 years unlike modern 3 years to e-waste junk !
@georgeindestructible
@georgeindestructible Жыл бұрын
We call over-heating something when it heats more than it can acceptably and reliably work within its specification (but this is not entirely and always true, not exactly at least, example given below). It may or may not work slightly near or above the limit but it may get its lifespan reduced. Using the board as a heat spreader, a passive cooler is a decent idea but it works only for very low wattage like 2-4 watts of heat tops and even then it depends on the how much area and how fast it can dissipate the amount of heat generated by x component, especially without making nearby other nearby components either overheat in the process thus have their resistance increased and work less efficiently and/or begin to reduce their lifespan. The actual reason why components fail is because heat makes metals expand, which reduces their ability to hold electrons in a stable state in their outer shells by over-saturating them (with kinetic energy, which itself also generates small amounts magnetic energy as a field, hence increases EMI) leading to destabilizing their structure and so, they break apart causing the component to fail. That kinetic energy has an osculation frequency which, if nearby components (like other nearby mosfets working, oscillating almost in the exact frequency also amplifies this effect by a tiny amount depending on the power of the EMI signal created and distance). A component does not need actually need to overheat for this to happen/fail, it can also happen to temperatures below the limits for the component itself, simply because for example, a soldering pad or ball is not the correct size for the current it has to pass through it especially long enough to handle it so it either melts by a bit, or entirely or completely and as a natural consequence, disconnects the circuit which is connected to. This is why i always say, design things in a way that they can never overheat unless you are doing it on purpose to see if and/or when they will/can fail. Edit: I forgot to mention the amount of electromagnetic noise a short from a broken component can cause to nearby components especially if its a very strong one, like, imagine a mosfet blowing for example. This is why i never like it when PC cases have disk places behind motherboard trays or near they PSU, like, if your disk drives survive a short somewhere else, but they are close to such EMI emission, the disks regardless if they are flash based or magnetic, are still reliable to fail in someway or another and have some or all of your data lost.
@Bjurran
@Bjurran Жыл бұрын
This is a great video to show why it is so important to not use computers in a very dirty environment, and if you do make sure you clean them often. I have many computers that are more than 10+ years running just fine as I take care of them. With the power draw, it is also important to point out the fact that people should keep their computers connected to power as often as possible and not only rely on battery as the battery will most likely not be able to give all the power for max performance.
@waynesallee-com
@waynesallee-com Жыл бұрын
And computers were made to last longer back then.
@Master777with69
@Master777with69 Жыл бұрын
Thankyou as a consumer this was really helpful and i am expecting more such videos😊
@fruitandnut
@fruitandnut Жыл бұрын
Thankyou for this explanation. Helps a lot.
@groovejet33
@groovejet33 Жыл бұрын
WOW...Sorin has gotta nice clean tidy new desk 😂 Your going UP in the world my friend😉 My 'All Time Favourite Techie'. Btw- Hopefully everyone has seen Sorins 'Back Alley Fault finding techniques & Tricks' If you haven't, your missing out BIG TIME 😉
@kriswillems5661
@kriswillems5661 Жыл бұрын
Very instructional. Thank you.
@justinspiredfallout
@justinspiredfallout Жыл бұрын
Great explanation. Thanks Sorin!
@v1ncend
@v1ncend 4 ай бұрын
Amazing demonstration, learning things, thanks Sorin
@MordenTVrepair
@MordenTVrepair Жыл бұрын
Hello our Master tech, actually I'm in TVs , but your way of thinking a troubleshoot helps me a lot
@manny9639
@manny9639 Жыл бұрын
Beautiful showcase and advice Sorin, greetings from Montreal 🙏❤
@alexgreis
@alexgreis Жыл бұрын
Amazing video. Thank you.
@coolerester77
@coolerester77 Жыл бұрын
Great video. Heat on motherboard is energy lost on processor power, so to compensate, more power is pushed to keep processing stable, but that can have bad consequences to moset. I never that of it that way
@warunakangara6791
@warunakangara6791 Жыл бұрын
Great advice sir ❤
@GregM
@GregM Жыл бұрын
Adding a thermal pad will not transfer heat very well if the back of the case is plastic. The thermal pad could trap heat if the pad is not sized properly and if there is no way to dissipate the heat that is building up. The thermal compound is to fill the small imperfections between IHS and the cold plate of the cooler. If one has to replace the thermal compound every 3 months then there are serious design issues in that laptop and cooling system.
@asv5769
@asv5769 Жыл бұрын
I have noticed that resistance actually drop with the rise of temperature, at least on some parts of the board. I also noticed this watching different repair videos. For example when shorted capacitor is removed and resistance is measured to check, it can be seen how resistance increasing as the board is cooling down.
@waynesallee-com
@waynesallee-com Жыл бұрын
From wikipidia; Silicon shows a peculiar profile, in that its electrical resistance increases with temperature up to about 160 °C, then starts decreasing, and drops further when the melting point is reached.
@8500gtNvidia
@8500gtNvidia Жыл бұрын
Very interesting video Master!
@Stabio_PL
@Stabio_PL Жыл бұрын
Hello Sorin. Thank you for another video :)
@paschalokeke3216
@paschalokeke3216 Жыл бұрын
Thank you so much for this wonderful tutorials ❤❤❤
@abdulrehmanmirza4244
@abdulrehmanmirza4244 Жыл бұрын
That's the best explanation ever ❤
@laidman2007
@laidman2007 Жыл бұрын
Useful. Thank you.
@emildan772
@emildan772 Жыл бұрын
O lecție bună și pentru cei ce nu înțeleg electronica.
@mhammmmagh1465
@mhammmmagh1465 Жыл бұрын
bineinteles 👍
@georgeindestructible
@georgeindestructible Жыл бұрын
Thermal pads on their own alone do nothing other than, some times become a saturated heatsink essentially "cooking" the component they are attempting to cool in the first place, you need to have something to take the heat off of them before the become saturated or somewhere in between the temperature limit the component can fail regardless because it can't handle the heat anyway. Passive cooling is only good when you can extract the heat passively fast enough something which it depends on the environmental temperature, which, the more it raises, especially getting near the component's temperature, the less the amount of heat will be dissipated/transferred away.
@sekyiemmanuel3059
@sekyiemmanuel3059 Жыл бұрын
Hello sir, I'm watching from Ghana now good job sir
@OMARENGG22
@OMARENGG22 7 ай бұрын
Thanks for explaining
@somewaresim
@somewaresim Жыл бұрын
Very interesting to see. Thanks
@kblectronix
@kblectronix Жыл бұрын
And people using laptops on a sofa or in bed which can block the air input/output. Better off on a desk, which somewhat depletes the point of a laptop 😀
@MadHeadzOz
@MadHeadzOz Жыл бұрын
Interesting. I've been dabbling with electronics recently, to help feed a curious mind and attempt to repair a part rather than replace the whole. I find mechanical fault finding etc fairly easy, logical and straight forward. The electrical side is a little less intuitive and ofcourse if is not obvious visual evidence fault finding requires more knowledge than I as a layman possess. This video clarified some things I have been told by techs I've spoken to. Combined with comments from other viewers more knowledgeable than myself, I feel I have gained a decent base level of comprehension. Ofcourse as is most often the case, answering a question poses many more questions. Lol. It is a major task just to access the parts to service them. Equipment being serviced is downtime for production. The ervicing vs replacing becomes hard to justify fiscally. I currently have a pretty decent thermal imaging camera on insefinite loan from a friend. I'm wondering if something like this used at semi regular intervals to check for variations in temp would indicate when work was necessary before something failed. Obviously I'd be viewing the housing/outside of the equipment. Not the components themselves directly. Mostly stainless steel and sheet metal or plastic. I feel like even with accurate imaging the temp differential may not be enough to pre-empt failure?
@danielstaneata5344
@danielstaneata5344 Жыл бұрын
very clear! ty
@meemorelive
@meemorelive Жыл бұрын
nice experiment
@IFIXCASTLES
@IFIXCASTLES Жыл бұрын
Great lesson!
@jenssonnenberg8620
@jenssonnenberg8620 Жыл бұрын
Multumesc, am inteles !
@blackdotkiller1
@blackdotkiller1 Жыл бұрын
A Cool motherboard is a happy motherboard 👍
@SkyDown15
@SkyDown15 Жыл бұрын
I would been intreseting to see you heating like an input mosfet while the board is on, and seen that mosfet get shorted. Input mosfet, or cpu mosfet, just with some current limit, so you wouldnt kill it :D
@electronicsrepairschool
@electronicsrepairschool Жыл бұрын
i will keep in mind next time :D
@oylumbilisim
@oylumbilisim Жыл бұрын
It's simple, semiconductors resistance decreases with the temperature rising. With less resistance devices tend to draw more current and more current means more heat and magic happens.
@rahulmechatronics
@rahulmechatronics Жыл бұрын
cool experiment
@anthonydenn4345
@anthonydenn4345 Жыл бұрын
What can also happen is the ABS plastic casing becomes brittle, drying out from the constant heat. The hinge stiffens up, probably from dried up grease, this then goes on to break the brittle hinge mounts, ending up with a broken hinge. The left hinge always breaks first, right next to where the heat is expelled from 99% of laptops. You have to ask the question, why is it designed that way. Bad design or again, planned obsolescence.
@tvdylan
@tvdylan 7 ай бұрын
I HAVE BURNT MANY MOSFETS ON MY PULSE MOTOR circuits. its is a big journey to learn how to master the operation of a mosfet ! i amstill learning ! -_-
@anasanasmk4211
@anasanasmk4211 Жыл бұрын
Good information👍
@ainsleyramai8311
@ainsleyramai8311 Жыл бұрын
Very informative video as usual Sorin. Very good advice to use thermal pads to transfer heat to the back of the keyboard or back cover. What was the current limit on the power supply vs the current of the original charger for this laptop? If we use a higher power charger on our laptop would this increase the risk of damaging the mosfets?
@rafarafa3094
@rafarafa3094 Жыл бұрын
Higher current power supply is always better to use. Look how u pick psu for pc, it should be 2x more wattage than your pc use. It apply to every electronics device. My advice is "DONT BUY GAMING LAPTOP" get a PC.
@surgingcircuits6955
@surgingcircuits6955 Жыл бұрын
Good Stuff! Thx!
@wahidumzee9013
@wahidumzee9013 Жыл бұрын
Definitely got schooled today
@ken-camo
@ken-camo Жыл бұрын
this is really cool i never even knew this
@knightwar3
@knightwar3 Жыл бұрын
Nice experiment it would be nice if you heat the two first mosfets and see how it will reacts
@Pulverrostmannen
@Pulverrostmannen Жыл бұрын
in simple terms it is also called "Thermal Runaway"
@Johny333-xk9js
@Johny333-xk9js Жыл бұрын
Can i replace mosfet with wire or solder?
@INerd2024
@INerd2024 Жыл бұрын
Guys, he is right but don't do that by yourself, I did that with my Acer Nitro5 AN-515-58-725A and it is not turning on after replacing the thermal paste. I accidentally unplugged the screen before Battery and the laptop shows shorts on the motherboard everywhere, it does not turn on, and I don't have a thermal camera and power supply to find the bad component on the motherboard. I am about to cry because I am a student and I really need my laptop I don't have it anymore since 2 months ago (dead laptop), and I am in a small city in the U.S. with very limited options including replacing the whole motherboard which is very expensive for me :(
@SamerM.ElMeligy
@SamerM.ElMeligy Жыл бұрын
Really I enjoyed the explanation for the problem Can I ask you a favour please? Do you have a video for reflowing the VGA in case it is not working properly ( especially in Dell laptops ) I tried to reflow it on 250 degree as many videos said but working for one week then played again So I need your experience if you have the same video just give me a link for it , or tell me what the suitable temperature to use when reflowing that chip Thanks in advance for all your efforts
@vytautasslenderis2702
@vytautasslenderis2702 Жыл бұрын
Reflowing a dead chip helps only temporarily (the heat "fixes" broken things inside). To really fix, you need to REPLACE the component, not to reflow it. See Louis Rossmann video about it.
@ishtiaq2000
@ishtiaq2000 Жыл бұрын
Great BREXIT Video. Love from Alberta, Canada.
@lawrencenjue2731
@lawrencenjue2731 Жыл бұрын
It's been supper impressive...
@jennytalia8224
@jennytalia8224 2 ай бұрын
If the mosfets may also overheat, would adding a heatsink make any difference?
@AimGobalWorldBibleSchool
@AimGobalWorldBibleSchool Жыл бұрын
Aspire ACER 5333 Got Watered on Keyboard it will not switch on.... only charging light....
@JuanFunQi
@JuanFunQi Ай бұрын
another learn lesson from the veteran
@21edijem-tutorial-tv
@21edijem-tutorial-tv Жыл бұрын
I have a question sir? my laptop samsung np535u3c has a light, its power has no display and its processor is not rotating, how can it be fixed sir, I hope you can help me
@ahmedbellil5161
@ahmedbellil5161 8 күн бұрын
you are the best thanks god bless you
@anhdetinh
@anhdetinh Жыл бұрын
Can I use your video to help people in my country, specifically Vietnam, better understand the importance of periodically cleaning a laptop?
@weerobot
@weerobot Жыл бұрын
"Where are my MosFets..."
@matmar4758
@matmar4758 Жыл бұрын
poate ai vrut sa zici rezistenta interna mosfet scade nu creste la caldura.
@ebilgin
@ebilgin Жыл бұрын
Siberia liked this video..
@Johny333-xk9js
@Johny333-xk9js Жыл бұрын
The Heat gets from this formula Q=I*I*R*t Joule law
@lucataszarek8782
@lucataszarek8782 Жыл бұрын
Hello🤝very nice 👍👍👍👍👏👏👏👏👋👋👋👋👋👋👋
@manISnoGOD
@manISnoGOD 9 ай бұрын
If I remove a faulty mosfet will the motherboard work without replacing new mosfet
@Pihmusik-PiCh-Expert
@Pihmusik-PiCh-Expert Ай бұрын
@qpgpq
@qpgpq Жыл бұрын
Electron energy increases
@53tech53
@53tech53 Жыл бұрын
Sir. Can you make video again about chipset and cpu short or die and power ohm chipset power ohm cpu. Thank you I'm from Cambodia
@saduniwathsala
@saduniwathsala Жыл бұрын
👍
@Rabah_Palestine
@Rabah_Palestine Жыл бұрын
❤❤
@KeyserSolsi
@KeyserSolsi Жыл бұрын
Thermal runaway...
@8peterp
@8peterp 8 ай бұрын
burnt a mosfet just with plugging in adaptor to 220v while was plugged into laptop
@MinecraftSerenity
@MinecraftSerenity Жыл бұрын
This happen on my laptop
@pylab22
@pylab22 Жыл бұрын
Hello
@jameschambers5505
@jameschambers5505 Жыл бұрын
Why you not postings videos every week.
@teslasapple
@teslasapple Жыл бұрын
👍🫡
@laboratorioassembler
@laboratorioassembler Жыл бұрын
Sorry Sorin but i can', t agree with you this time... Replacing the thermal paste IS just a russian roulette for the gpus and cpus... The thermal dilatation, flexing the Board with the screwdriver and removing the pressure of heatsink can cause The balls to crack... Loosing audio... Loosing linees on gpus.... Loosing enterely operativity of CPU or PCH... Loosing the PCI express 16x... And a lot of things... Better just to clean fans and heatsinks from dust... The thermal paste can be replaced after 3 years... Just for chemical degradation.... And what about heatsinks/thermalpads on first 2 mosfets??? You saved the Board because the mosfet goes shorted... But first layer of the pcb was damaged... Pressing the mosfet and add thermal Pad can just increase the damage to internal layers making them fuses before The mosfet got killed... I saw lot of Asus x550 with layers merged under The first mosfet... Better to have a shorted mosfet than dig and scratch on layers to remove shorts.
@obodoedirin4273
@obodoedirin4273 Жыл бұрын
So l have a dell Alienware 17 r4 when l try to power it on it shows orange and white light but no display, if l try more times it will display and go to the desktop what can be the issue
@laboratorioassembler
@laboratorioassembler Жыл бұрын
@@obodoedirin4273 the issue is that is a gaming laptop.
@TTT-V
@TTT-V Жыл бұрын
Ive just placed an order the thermal pad
@jameschambers5505
@jameschambers5505 Жыл бұрын
Thanks for the videos sir
@yvesrochet3288
@yvesrochet3288 7 ай бұрын
Very interesting Thks Sorin
How a faulty mosfet looks like - HP G60-214EM laptop repair
21:54
Electronics Repair School
Рет қаралды 64 М.
How to find a shorted mosfet - safe & fast, no thermal camera or multimeter
17:15
Electronics Repair School
Рет қаралды 217 М.
Cat mode and a glass of water #family #humor #fun
00:22
Kotiki_Z
Рет қаралды 37 МЛН
coco在求救? #小丑 #天使 #shorts
00:29
好人小丑
Рет қаралды 114 МЛН
VIP ACCESS
00:47
Natan por Aí
Рет қаралды 28 МЛН
Wall Rebound Challenge 🙈😱
00:34
Celine Dept
Рет қаралды 23 МЛН
Laptop Motherboard Repair - Came in from India. How bad can it be ?
10:32
Asus GL502v Laptop Repair No Power- How to Test for a Bad Mosfet
10:10
Another Graphics card not working after cleaning with an air duster
8:50
northwestrepair
Рет қаралды 2,4 МЛН
{502} Why IGBT Burns Out After Replacement - IGBT Damaging Reasons
18:53
Haseeb Electronics
Рет қаралды 41 М.
Are Graphics Cards Repairable ?
12:12
northwestrepair
Рет қаралды 30 М.
Gaming laptops classic disease - Shorted CPU/GPU mosfet - Msi gaming laptop repair
15:45
Cat mode and a glass of water #family #humor #fun
00:22
Kotiki_Z
Рет қаралды 37 МЛН