Ender 3 V2 3d Printer Problems, Solutions & Troubleshooting

Troubleshooting common printing problems with a Creality Ender 3 V2 3d Printer. Things to check if you're having trouble with the Ender 3 V2. Issues with bed leveler, Octoprint and BL touch.
Also, upgrades that can help.
Please subscribe & like for updates. MY UPGRADES BELOW......
Creality Ender 3 v2 (3D printer); amzn.to/36T4mCt
Dual Z Axis Kit: amzn.to/32A2nDO
Bed Springs: amzn.to/2YUnuf2
Replacement NOZZLES..amzn.to/30DhSKm
Replacement Hot End: amzn.to/3mdfdi8
Ender 3 Glass Bed: amzn.to/3e2Sxwy
Silica Dry Packs: amzn.to/3q7mAJc
Damp Rid Dryer: amzn.to/3FdpimA
ALL Metal Drive: amzn.to/3oYEJGD
FLiR Thermal Camera for IPhone: amzn.to/328cGyY
BL Touch Auto Bed Leveler: amzn.to/36QW9P4
Dual Z Axis Upgrade:amzn.to/3yE23Qh
Raspberry Pi Controller; amzn.to/2MHdzXz
Pi Case: amzn.to/3tuhx6m
Pi Camera: amzn.to/36T3FJf
Pi Camera Extended Cable: amzn.to/3oVg8Cl
Remote Switches: amzn.to/2YSiuaL
LED 3D Printer Lights: amzn.to/3rzjigG
DROP-IN (not snap in) Slot Covers (Free to print yourself): www.thingiverse.com/thing:470...
*I am an Amazon Affiliate. These links support my channel. Thank you for helping. The items above are the exact items in the video. If you have any questions - please comment!!
Our Patreon page - Please support the channel by signing up to get privleges and extra content.
Click here: / realworld1

[@FrotLopOfficial]

You can definitely slightly adjust the glass bed. Just put 1 or 2 layers of tinfoil. The glass is heavy enough to bend. You may just need to add 1 clip per edge (compared to just the 2 included clips. Clips are about $5-10 depending where you get them, or you can also 3D print a longer edge clip /half-sleeve

[@TheRealWorld737]

Great tip. Thanks!!

[@firstnamelastname2111]

Thanks for making this,

[@cosmickidd205]

Hi,just seen your video.my problem is when im remote setting my ender3 v2 neo the bed moves back and the motor is still going,im new to printing and have no idea how to fix it.

[@spudnickuk]

Good video and information. Can you ad a link to your firmware version as it has been updated for bedevilling features.

[@TheRealWorld737]

github.com/smith3d/Jyers_Marlin

[@TheRealWorld737]

Also... The upgrade to the Jyers firmware was the BEST thing I've done for functionality and ease of use for the Ender 3 V2. It's amazing the options it gives you!

[@spudnickuk]

@@TheRealWorld737 i am looking forward to changing the Display firmware. Nice to be different and better LOL :)

[@TheRealWorld737]

It is SO much better!! Yes!

[@JNKM-rl1wu]

I know this is a shot in the dark but I don't know what to do..I have an ender 3v2 I bought brandnew worked great until I started having the same issues your having so I took it apart cleaned it all now as soon as I press print it warms up then says print stopped.. does nothing else.. I have purchased a all metal extruder capacorn tube and micro Swiss hot end along with new nozzles. I have not installed any of it yet.. just trying to figure out this issue first.. and in would be greatly appreciated

[@TheRealWorld737]

Probably the hot end. I had a defective thermistor

[@KaesenGraff]

My ender 3v2 keeps saying nozzle too low temperature mid print, do you know how to fix it

[@TheRealWorld737]

More than likely your thermistor on the hot end. For about $20 you can replace the whole hot end with this kit that comes with the thermistor: amzn.to/3Rz0AnC

[@nathanpeters4981]

@@TheRealWorld737 Or just make sure you have the Silicone protector on the end

[@salvi2807]

What do you do if the print keeps changing the print speed to 990 % and also when I try printing the axis doesn’t move up so it’s just starts engraving into the print

[@TheRealWorld737]

That I have not run into. Anyone else see this?

[@NCIA-93]

My printer has leveling issues. After leveling it works fine, until i turn it off and back on later... Suddenly its home position is too high up and the filament doesnt touch the glass plate. I marked the leveling screw wheels and they dont move at all. What can cause this?

[@TheRealWorld737]

Make sure when you set the z offset - that you save it in the settings. Seems obvious- but that’s what I would check first

[@jakobchannelhere]

homie u sound like a chill owen wilson

[@jpbrandom]

I have an issue where after 10 minutes of heating up before making a print, it will start screaming amd saying the temp of the nozzle and the bed are too low. Anyone know how to fix that?

[@TheRealWorld737]

I would look into checking your thermistor. There’s probably some KZbin videos on that. Most likely it’s not sensing properly.

[@holymagg]

whenever i slice a print from cura, and then start printing it, my printer crashes at the start. any solutions?

[@TheRealWorld737]

First thing is to check your printer firmware. Then - check the see if you have the most up to date Cura. It’s possible there’s some Gcode that’s been inadvertently inserted into the beginning of the Cura slice code. If it were me, after checking the first two software issues - update - if that doesn’t work- try uninstalling and reinstalling Cura. Also- I now use Prusa Slicer. Try that if what I said before doesn’t work for you. I like Prusa slicer and they have Ender profiles you can download for free.

[@nathanpeters4981]

What firmware are you running?

[@TheRealWorld737]

Jyers_UI v2.0.1