Engineering Drawing How To Use Mini Drafter

[@AtishYadav-dm9xc]

🎉🎉..A lot of Thanks sir..❤❤❤

[@AtishYadav-dm9xc]

Ha..

[@digvijayshukla3157]

Great work sir, this will always be helpful for the students who doesn't have a basic infrastructure

[@shambhavisingh6675]

Amazing explaination 👏

[@Backbencher10-v7z]

Thank sir tomorrow my ED exam 😊👏

[@akhtarahmadsw9115]

Thanks a lots sir bahut hi nice explanation aapne kaam ki chij sikhaye

[@TheDhairya101]

UCOE Drawing sheet reminded me old days

[@hardavsharma1936]

Great work sir, thank you

[@Surajsuhanaa]

Thanks sir 🙏

[@sciencelife3259]

Super sir

[@TheDhairya101]

very informative video sir🙏🏼

[@alekhasahoo4736]

❤❤❤❤

[@innocentkitangwakalenga8383]

Hello, sir can you please make video on drawing this Instructions: Answer ALL questions. In this assignment, question (a) below is a description of a system and (b) provides information about a graphical plain scale. Question (a) requires the construction of two views of the artifact described, while (b) require the construction of a plain scale conforming to the information given. Both the two views and the graphical plain scale are to be drawn in the same drawing area of an A3 drawing sheet, laid in landscape, appropriately centralized as taught in this module. Please note that part (b) requires some prior calculations, these calculations shall be done in the drawing area (i.e., defined only by the standard margins and title block as taught in this module) on the flip side of the A3 not used for the views and the plain scale.(ONLY neat presentations earn credit). [Do not dimension your drawings unless explicitly asked to do so!] [deduct 5 Marks if unsolicited dimensions are included]question 1 [100%](A). A cleaning company contracted by BIUST has commissioned you to design a special tool with which to remove sticky chewing gum on the floors of student hostels. The tool is to be called a SCRAPER and its overall shape is a rectangular solid of 120 × 80 × 10 mm. However, one end of rectangular solid rises from zero thickness to a maximum thickness of 10 mm in a length of 30 mm to form a sharp edge. The opposite end is semicircular. A 30 mm diameter hole is positioned such that the center of the hole is 40 mm from the semicircular end and 40 mm from either side of the tool. Use an A3-size paper to appropriately layout a full-size drawing of this concept as presented by the cleaning company. Your drawing should, in appropriate portions: 1). give, in 3rd angle projection, the front view (FV) and top view (TV) of the tool appropriately centralized with the title block assumed to be 12 mm high, in which only 2) the name of the tool, 3). Your Student ID should appear neatly written. [50%]B) At a convenient place above the scraper in (a) above, construct a plain graphical scale to depict the situation whereby a field of 7.2 square meter is represented in a map by 10 cm x 8 cm. The scale should show centremeters (cm) at the lowest level but long enough to measure up to 3 meters (m). Be advised that the height of the scale (or the height of the thin long rectangle) shall be 10mm instead of the recommended 3mm taught in the module. This height is very important especially for centralizing your views vertically [50%]

[@divyaprakashsinghmaurya3570]

Thank for you sir 🥰🥰

[@sohum.narwani]

thank you sir

[@deadshots8274]

Thanx sir ❤️

[@SachinVerma-rs6oj]

Sachin Verma

[@graduatecoachingwala]

Sir new topic agian lecture universal coupling plz sir

[@vivekvivekkumar9900]

Sir draw single stork vertical glothic lettering