I worked at a steel mill and was a crane operator on a 100 ton P&H gantry crane that could be operated by remote control. Everyday, my crane operation report said "brakes don't work." Well, one day the remote battery died. And you could hear the "clunk" of the brakes actuating when the remote battery died, but the crane didn't slow a bit. It was going at 5 points when that happened. By the time it reached the end of the building, it hadn't slowed down hardly any. It hit the stops and ripped them off (luckily, there was another building that ran behind it and was butted up against it and kept it from leaving the building) and all hell broke loose. It ended up sitting askew on the rails, with only 4 of the 8 wheels in contact with the rail. I got the attention of the roller on the line when it happened and he got on the speaker and informed other down the line and they were all running like Godzilla was on the loose. KER-BLAM!!! Instantly, I got blamed, until I showed the big boss a couple months of crane reports. It damn near came off the tracks.
@steelplant551911 ай бұрын
🙏
@ChibabaDave9 ай бұрын
It blows my mind how some boses seem to ignore what their maintenance guys tell them, or worst still let blatantly incompetent people work on them.
@rajeevkumar-dv1gv2 жыл бұрын
Wyz 350/45 thruster break ka adjustment kaise karte hain
@ooo49373 ай бұрын
Sir EOT Crane ka wire rope kitna%ma change hoga
@rishiraj6491 Жыл бұрын
Complete adjustment explain in next videos the same type of thruster brake
@steelplant5519 Жыл бұрын
ok sir
@ChibabaDave2 жыл бұрын
What is the reason for adjusting the springs?
@raghava56242 жыл бұрын
Spring act as counter force to thruster movement. When thruster is activated spring compresses. When thruster released spring act its compression force on thruster and it helps thruster goes down quickly. If you adjust spring means you are indirectly setting thruster to close fast. Once thruster is closed spring duty is over. Then thruster uses its own dead weight to bind brake shoes around brake drum.
@ChibabaDave2 жыл бұрын
Should it not be factory set though? The thruster speed is adjusted by the oil flow valve is itnot?
@himansukumardas46603 ай бұрын
Nice👍
@mayurchaudhari8529 Жыл бұрын
Why brake shoe burn or smoke release during operation
@ChibabaDave Жыл бұрын
Its too tight if its doing that.
@user-ys1ws8pz1f5 ай бұрын
Good job
@Industrialmaterialhandling Жыл бұрын
Good sir
@steelplant5519 Жыл бұрын
Thank u
@debankighosh28532 жыл бұрын
Goood
@steelplant5519 Жыл бұрын
thank
@medleydeluxe5298 Жыл бұрын
What on earth are you doing
@ChibabaDave Жыл бұрын
It honestly doesnt look right to me, it should be adjusted by the nut on the right hand side of the tie bar to compensate for wear. Those springs should be factory set to provide a specific load of braking torque. Its not clear to me why they are adjusting them unless someone has already messed about with them.
@user-xf3pj7zm1q2 жыл бұрын
What kind of oil do you put in the thrust?
@raghusingh7718 Жыл бұрын
Transformer oil
@m.de.o.tcranemaintainer6824 Жыл бұрын
Hydrolic oil.
@steelplant5519 Жыл бұрын
TRANSFORMER OIL
@yadavpintu5080 Жыл бұрын
Traformer oil
@user-oq3es7qq7x10 ай бұрын
@@steelplant5519ну ты же видишь тупорылый!! Что это тормозное устройство не для этого тормозного барабана!! Барабан больше чем надо!!! Тупицы!!!!!
@zitel-zemli0671 Жыл бұрын
А не судьба отрегулировать тормоза, двумя гайками на шпильке?! И масла долить в гидротолкатель. Он не полностью открывает тормозные колодки.