ERROR 06 & 07 ON M4 ELECTRIC SCOOTER (JX-168 & TF100).

[@garryv.r7288]

Why you didn't show how you found out the lost connection and how you repaired it?

[@nhelpineda]

You are right bro i fail to show that, basically its either the green or blue wires having loose contact. If you found everything is okay then you have to check your motors hall sensors error 7 also sometimes are hall sensors error.

[@garryv.r7288]

@@nhelpineda salamat sa reply bro. God bless you.

[@Hijo-del-Chico]

Yo tampoco entiendo para que sirve un vídeo, donde no podemos ver, como has arreglado el fallo... no lo entiendo, tienes todos los medios, y dejas la cámara mirando para las musarañas.. muchas gracias por nada

[@nhelpineda]

@@Hijo-del-Chico hello friend feel free to drop your question here in comment section, thanks to google translate i was able to understand your language. I am happy to help, hopefully the best i can.

[@arifedding4900]

Sir can i connect the blue wire and green wire for display and controller?

[@LouiePage-g1e]

Hello mate have the same. Problem... No loose wires at all. As hardwired all connetions. As cut them all off. Soldered all wire's so ni block connection. Still getting error e-006....no loos wires or dry solder joints inside tf-100 throttle. What do u think i can try next

[@nhelpineda]

Hi mate make sure that your battery voltage is correct, if so it means that the controller really is faulty. You have to buy a new pair do not buy if it is not in pair. It should comes with throttle and a controller to avoid problem and wasted purchases. I hope you can fix your issue.

[@thetruthissurreal]

I just went thru all this with yunli controllers and lh-100 amd tf-100 bought 4 of them bf it was done I burned up both controllers don't know if I messed up the motors or not.BC the first error was my sensors were bad in my motors.replaced those then got 6 and 7 and never got rid of them I hard wired it all too man.I and beyond pissed off.it was sup post to be plug and play cost me 300.00 all together destroyed a 1,400 dollar scooter and now I'm gonna have to buy new controllers new motors and the display..the scooter only had 400 miles on it.the yunli strollers were supposed to be great and plug amd play anything but and of course ordoo speed won't help at all but to say it was my fault.

[@nhelpineda]

Hub motors will not be easily damage sometimes hall sensor becomes faulty it is easy to test though just supply power on your controller with you hall sensor cable connected as it is then test it one by one black probe of multimeter on negative or black wire of hall sensor then test the red green and blue one by one, you should get 4-5vdc and becomes 0 once you slightly spin the wheel all of them must have the same values.

[@nhelpineda]

Error 6 and 7 is due to communication errors between throttle and controller and also hall sensor sometimes when they are faulty.

[@nhelpineda]

I recommend do not replace your hub motor as it is still okay and usable if the hall effect sensor is faulty you can replace it check this product link Honeywell SS41 SS41F HALL EFFECT BIPOLAR SENSOR IC a.aliexpress.com/_oofiL8I, it will not be faulty that fast it is meant to be use for long term unless something else happened, if you buy your controller please try to buy it in pair with throttle for compatibility reason.

[@shmulis3027]

Hey, would you know why I can't find the spot to disconnect the old throttle to connect the new one?

[@nhelpineda]

What is your Scooter model bro?

[@nhelpineda]

Most of this type of scooters has a 6 pin connector near the throttle if you are replacing the same model its okay, but if you are going to use different model like i did, then you have to open the new throttle and check the wiring arrangement.

[@alejandromoralestedone9853]

I have 07 error but, It appears and disappears continuously, so the m4 pro scooter runs like a hawk, it accelerates and decelerates so it becomes so unstable and dangerous.

[@nhelpineda]

Hello Alejandro Thank you for dropping a comment here

[@nhelpineda]

First you have to Check your hall sensor if it is all functional you can check it by placing the black prove of multimeter to the black wire then test it one by one colors are mostly yellow,green, and blue by rotating the wheel slowly you should get 5VDC and it will change value when you move the wheel again. Look for five small cables 5 pin mostly white connector that is for the hall sensor.

[@nhelpineda]

Note!! You can test the hall sensor phase one by one the black probe will be permanent in a black wire - the red probe you can test each hall wires ( yellow, green, and blue.)each phase should have the same value of reading as i mentioned above.

[@subkarpaty]

red triangle on my tf-100 no error (0) why red triangle on lcd? is this break waring?

[@nhelpineda]

Exactly bro that is for break indicator, everytime you break red triangle will always apear its normal.

[@adsmith9963]

Why show a video when you don't show us what wire is the problem

[@nhelpineda]

It was TX or green Cable on the throttle that having loose contact, i don't have holder for my camera bro thats why i keep it in one place sorry about that.

[@ravelsmusic]

E-6 showing up on my monitor do I need to replace the Motor? Thanks

[@nhelpineda]

No its not the motor fault check your controller and LCD Display connection there might be loose wires, also check your battery voltage it is also insufficient voltage sometimes.

[@callumfynan8292]

Bit of a weird one i replaced my throttle as it was snapped off the original works fine just the clamp for the bar is broken then i switched over to an identical throttle and it comes up with the e-6 error can you help me

[@nhelpineda]

@@callumfynan8292 I also noticed the same thing that is the reason why when I'm replacing it i make sure it is in pair, Try removing your alarm system if the error will be gone.? There us a chance that it is the same model but the RX & TX connection maybe swapped.

[@nhelpineda]

@@callumfynan8292 that is why i resolder it since it is really different model.

[@scary578]

Can ya help with what is E-2 , E-5, E-6 I've all those errors

[@nhelpineda]

Thank you bro for droping your Question. Error-2 refers to a Throttle fault itself, error-5 is a voltage protection either under or over voltage causing this fault. E-6 is basically communication between throttle and controller, these error codes are similarly common in majority brand of Chinese scooters.

[@ryanbolisay9272]

Sir pineda how did you fix it, i have the same problem.

[@nhelpineda]

Bro what error do you have? If you get the same error, normally there is loose wiring connections between your throttle and controller.. With my error i just found loose connection on green wires from throttle to controller.

[@zico3239]

9 out of 10 of chines stuff they just never work or they broke in a couple of weeks or day

[@nhelpineda]

Yes you are right, it is difficult for those who cannot do a troubleshooting on their own, letting repair shops to do it will cost you extra as chinese scooters often does not have a warranty.

[@maximus7618]

E-6, E-06, E-006, they are not the same fault code.

[@nhelpineda]

I saw it all the same i guess.

[@maximus7618]

E-06 is battery under voltage

[@nhelpineda]

Yes exactly! or lets say below the controllers required voltage.

[@maximus7618]

@@nhelpineda can you help me diagnose my issue.

[@maximus7618]

I was riding my scooter the other day then it shuts down on me. When i turn the key back on i get error fault E-06. Key off then on again, noticed 54.6v with same error. 1 min later key off then on, the battery voltage from 54.6v would drop slowly down to 0v. Key off then on, completely no reading from voltage gauge. What could be the problem? Please help. With direct charging from outlet source, 58.4v and doesn't cut off. Btw noticed when i plugged charger into one of the scooter charging port, i hear like an arc sound but disapper afterwards.

[@metekarabacak2234]

İ bought new throttle JX-168 so when i replace it i have the same error, but when i replace the old one i can’t see the error and the scooter works🤷‍♂️

[@nhelpineda]

Hi bro, yeah most of the controllers have the same issue. If you are planning to buy a new controller you should buy it always in pair with throttle to avoid spoiling your purchase. It will always give you an error if you connect your new throttle or controller with old one vice-versa.

[@metekarabacak2234]

@@nhelpineda i understand, i want to order throttle and controller but i don’t know which controller is suitable to my scooter, 48V 21Ah, and also do the scooters with dual motors use 1 or 2 controller?

[@nhelpineda]

@@metekarabacak2234 it depends on the controller some are suitable for dual motor in one single controller others like kaabo mantis they are using two cotnrollers which one do you have?

[@metekarabacak2234]

@@nhelpineda i checked it, its 2 controllers, but here in my scooter they were small by size but my scooter is 48V 21Ah 800Wx2, i checked on aliexpress, the products with their size are only 350w, i wanted to by 40V 25Ah 1000w controllers but it’ll not fit in my scooter they are big by size, i’m facing problems by choosing the watts

[@nhelpineda]

@@metekarabacak2234 check this out Bro this might match your needs but make sure you will buy throttle for G-booster as well. G-Booster Electric Scooter Motor Controller Parts For KUGOO G-Booster Controller Kickscooter Replacement Accessories a.aliexpress.com/_mt45xdC

[@fawadshakuri4056]

I have same problim but i dont no what i make ?

[@nhelpineda]

Check for loose wirings as it is the possible cause of error.

[@levyciobanu]

Error 10 how to fix it thanks

[@nhelpineda]

There are two ways to solve this issue First; check your wiring between throttle and controller for any loose connections, Second; if the first steps was done and did not found any loose wirings replace your controller. I advise to replace both controller and throttle in pair.

[@cabsblog8673]

Error 4 how to fix

[@nhelpineda]

First check your battery voltage, if the battery output is stable then you have to Check your controller that might be causing error. Either of this 2.

[@jeissonandreslosadacastro4311]

Hola tengo el problema que cuando enciendo la luz y anda un poco sale el error 007, y las apago y desaparece el error

[@nhelpineda]

Hi @jeissonandreslosadacastro4311 thank you for this very helpful Question.. I encountered this problem before, everytime i am going to switch on my headlight and the rest of accessories i am getting error 07, I've learned that this is related to the voltage i observed that whenever i switched on the headlight the voltage suddenly drops, i believe there is a shorted in the lighting output with your controller. I fixed mine by relocating the lighting power supply directly to the battery since the power supply required was 48vdc If you don't want to modify your wiring like what i did you can replace your controller as there is a shorted on that lighting power supply output.

[@nhelpineda]

I am still using the same controller without having a problem, i just relocated the lightings power supply now my scooter still running just fine. If you have 48vdc lightings you can use the ignition output to supply it. No need to change the negative as it was common connection, just rewire positive.

[@misokompus8688]

Plase help my E-6

[@nhelpineda]

Check your battery voltage the controller might not get a sufficient voltage required.

[@yahyaimrani8317]

Hello, can you contact me? I have the same problem

[@nhelpineda]

What is your scooter model bro?

[@nhelpineda]

Have you checked all the wirings, battery voltage either of this are having problem.

[@nhelpineda]

If you haven't seen any of those problems you should replace your controller set but make sure you've checked loose wirings carefully to avoid unnecessary spending of money.

[@UNKOWN_SOURCE]

I have the same issue i hope you could send reply on how you do it atleast. Thanks in advance.

[@nhelpineda]

How can I help you? Try to check all contact points carefully sometimes errors happens when there are loose wiring connections, shorted in circuit wirings or sometimes a faulty hall sensor. Also check your battery voltage to make sure that is not causing this error.