Couple of tips I learned in the struggle to fit my new seal to the same machine in the video. Start the seal at the bottom.not the top as shown, then you can just about see when the lip of the seal is on the rim. Start at the top and you won't be able to see. Slide your fingers around the seal, pressing in very hard, either side once the first part is on and gradually work your way up and around. My seal made a crunching feeling as it went on. The spring hoop that secures it is almost impossible to fit as others have said. I stretched the spring a but to take a bit of the tension out of it, and that helped a lot, enabling me to get it on with a helper. Another thing that helped putting on the spring was to fold the loose rubber seal (the part you will attach later to the outside of the machine) inwards into the drum to give room to fit the spring.
@eSpares7 ай бұрын
Hi, thanks for your comment and for sharing the experience you had when doing your door seal replacement. Great to hear you have been able to fix your appliance to keep it going.
@williamfalcon73514 жыл бұрын
agreed with all the comments below, he didn't do that in 15minutes !! took me 3 1/2 hours of grunting and trying to manage a slippery piece of rubber in a small gap !! oh and did it on the floor in my utility room not at shoulder level
@eSpares4 жыл бұрын
Hi william, the video is condensed after filming but still can show how to do it, we understand this can be a difficult repair but well done for fixing it.
@Gb-vk3ph7 ай бұрын
Similar to a lot of the comments here I found this job extremely hard and not at all as easy as the guy makes it seem in the video. Consider how much you are willing to take on before this job as it is not for the faint hearted
@williamfalcon73514 жыл бұрын
Thank you for the reply, i also had to contend with the additional task of connecting the washing powder/dispenser hose to the seal as well !! It now works after my son helped
@eSpares4 жыл бұрын
Hi william, thanks for letting us know and well done for sorting it.
@nicolasmith77146 ай бұрын
Not sure about the comments. As a mum of 4 I was determined not to buy a new washing machine. Yes it was hard and yes it took about an hour but the video was very helpful. My washer has the water intake at the top of the seal to contend with as well. Thank you for your help and advice ❤
@eSpares6 ай бұрын
Hi Nicola, thanks so much for your comment. It really is great to hear that our video has helped you to keep your washing machine up and running, especially as it sounds like you have to do a good amount of washing. Well done on completing the seal replacement yourself!
@paulcordingley19735 ай бұрын
Please come around to my house and help me!!
@MegaDogsBollox8 ай бұрын
Nice promo to encourage buying a new seal but those cuts in the video hide all the technique
@FoxyLoxy110 ай бұрын
I managed to get most of this done relatively quickly (about 45 mins with a few attempts!) to get the seal attached. However I cannot for the life of me get the spring gripper back on, even with an extra pair of hands! Also have the dispenser part to reattach which makes it a bit more fiddly. We need a 3rd pair of hands I think so hopefully I will get it sorted soon!
@Jennyhemming-l3f10 ай бұрын
Hi did you manage to do - we are currently struggling with this part any advice greatly recieved.
@FoxyLoxy110 ай бұрын
@@Jennyhemming-l3fYES! What we ended up doing was putting the machine on its back. The weight of the drum pushed it down towards the back of the machine, which created more room to get 2 pairs of hands in between the drum and the outer of the machine to stretch it round, if that makes sense! Still very fiddly but considerably easier than having the machine upright! I hope you get it sorted! 🤞🏼
@billjudd9210 ай бұрын
How did you remove the dispenser part. Struggling to remove the wire around it
@FoxyLoxy110 ай бұрын
@@billjudd92the wire around the dispenser part on ours was a small wire clip that just had to be pinched inwards to unhook/rehook it. I hope that makes sense. I hope you get it sorted!
@keithlawton78216 ай бұрын
His machine isn't the disp type into the top of the appliance seal
@johnchandler63434 жыл бұрын
To change the seal as per the e spares video is far too difficult for the average DIYer and if the drum has a close fitting counter weight, forget it, take the front panel off, it makes life so much easier. It takes less than 15 mins to remove the front panel and another 20 mins to replace the seal. Even with the front panel and counter weight removed it is still a very fiddly job. I always use eSpares for replacement electrical parts, they provide great service at very competitive prices and offer next day delivery.
@sabix0802Ай бұрын
Hi can you help us ,we poll out wash gasket but we tok out only 1 retaining band ,we don't know how to find another retaining band Our Washmachine is Zanussi 184 W,can you please help us :(
@SL-nd6pz7 ай бұрын
Video is misleading I could not get inner Seal to fit. Returnee item and decided to buy new washing machine
@keithlawton78216 ай бұрын
I'm a zanussi engineer and without removing the door it can be done in 1 1/2 mins
@paulcordingley19735 ай бұрын
Yeah right!
@mariposa69054 жыл бұрын
Sadly you don't show the crucial part of how to fit the inner lip around the rim.
@eSpares4 жыл бұрын
Hi Mari, it was difficult to show when filming as the camera can't get in while Mat has his hands inside, Mat did explain exactly what he was going to do in detail before fitting it but we will do better in the future, thank you for bringing it to our attention.
@keithlawton78216 ай бұрын
He's doing it the way I would do it, apart from he removes the door
@andresjulie21345 жыл бұрын
Just ask if can replace other one
@eSpares5 жыл бұрын
Hi Andres Julie , we are a little confused as your machine only has 1 door seal so can you let us know what you mean.
@Dedears4 ай бұрын
At the and vidro brcame usuless with hiding or cut parts
@liamjones97976 ай бұрын
Take the whole front cover off. It’s a thousand times quicker and easier
@adrianwalker42297 ай бұрын
Save yourself all the bother of trying to fit the spring hoop this guy blatantly skips out of the video by removing the front cover of the machine. After spending hours trying to fit the hoop then giving up, I got up the next day and managed to work out how to take the face off the machine, fit the hoop, reassembled the machine, fit the rubber seal to the face and then fit the second hoop to complete the whole job in well under an hour. It was pretty straight forward. Just be careful with the wires to the pcb, which you can disconnect and also the wire to the door locking mechanism which I didn’t bother disconnecting as it looked a little awkward. If you need any help drop me a message and I’ll talk you through it
@SL-nd6pz7 ай бұрын
Video is misleading I could not get inner Seal to fit. Returnee item and decided to buy new washing machine