Basic connection of pc to panel using tools 8000 software fire alarm system. Create backup from your pc, control the panel, make diagnostic and loop testing.
Пікірлер: 43
@prithivraj18393 ай бұрын
Thank you brother
@PLATINUMGAMINGPUBG2 жыл бұрын
Very informative videos. Thanks. You are great
@topbrooutdoorbreeze2 жыл бұрын
great dude..
@VincentSy-ni6lqАй бұрын
Can you give me some reasons why sounder of esser panel is not triggering?
@abdulnajeeb372Ай бұрын
v46 led light on mother board of IQ8M panel LIT ON, and panel goes to very limited operation.... Any recommendation how to resolve this issue?
@PLATINUMGAMINGPUBG2 жыл бұрын
Please also make videos on software and firmware. It should be same or...
@markgestadavid2 жыл бұрын
For software you can just upload a blank data so the panel will have a clear format (an empty or blank system), for firmware its very sensitive that you update or erase the firmware it might destroy the whole panel as you know how expensive the panel is.but if you have the original firmware or backup of it,atleast you can restore the panel to its original state.thanks
@PLATINUMGAMINGPUBG2 жыл бұрын
@@markgestadavid I have 1.15.1 version of Tool 8000. is it ok? also i checked many panels , that we cant connect laptop directly through printer cable its requird serial bus controller
@markgestadavid2 жыл бұрын
@@PLATINUMGAMINGPUBG try higher version like from v 1.19.1 to 26, your version might not support the usb driver to connect from pc to panel
@camilmanafli Жыл бұрын
@@markgestadavid How can i download tool 8000 ? Could you send me last version ? Thanks.
@gostavomostafa9174 Жыл бұрын
Hello I have a problem with my esser iq8 i had to move it Somewhere else and when i powered it again it shows random faults i did a loop wiring test with tools 8000 everything is good but still showing faults Are you familiar with this?
@markgestadavid Жыл бұрын
You need to reprogram and upload it to the panel or check the loop card if damage,the loop wiring if properly connected or no short circuit. You need to check the fault what it is giving you to make sure
@gostavomostafa9174 Жыл бұрын
@@markgestadavid u mean inject the same programe i have to the panel ?!
@markgestadavid Жыл бұрын
@Gostavo Mostafa if the panel has no problem before you remove to its original place ,then you should have no problem,but as you said faults came,then you need to check your wiring connection and everything.if faults still exist you really need to reprogram the panel accordingly to remove faults as a new commissioning panel to remove faults.
@gostavomostafa9174 Жыл бұрын
@@markgestadavid ok thank you i will try that Other question i have tools 8000 v1.19 and i want a higher update how can i get that ?
@ab-ph1np10 ай бұрын
My system was working fine. I connected my laptop and through tools8000, i downloaded tge data. But now tge system is asking for password for the panel. Bht i never put the password. Any ideas???
@markgestadavid10 ай бұрын
Try 1234, the programmer put password so no one can edit the program,sadly you cannot by pass it,the only way is to reprogram the panel and overwrite the program or flash the memory to return it to factory default panel all data will be erase.
@MuhammadAhmed-vk7fj2 жыл бұрын
i need esser software
@markgestadavid2 жыл бұрын
What version you need? You can email me at markgestadavid@gmail.com
@entertainmentvlogs69519 ай бұрын
Hello i need your urgent help please tell me i am in trouble now.
@markgestadavid9 ай бұрын
What?
@alexandaralexandar38542 жыл бұрын
How to program in transponder in fire and fault
@markgestadavid2 жыл бұрын
You can assign it in sector, either you put a resistor to trigger the fault or program it
@Afzal2143 жыл бұрын
How we solve fault from the pannel? I already clean the smoke but after reset he came again. So after what the solution?
@markgestadavid3 жыл бұрын
You need to replace the detector if the device is really the problem and you need software to do it.
@Afzal2143 жыл бұрын
@@markgestadavid here is iq8 control pannel. And 2 different loop have 2 fault at diffrent location. First i did clean the device and after make reset. Again fault came. After i did change that smoke with base and make programme of replace smoke. But after some time again fault came. So now what i do? Because i follow all step of solve the fault but fault again came.
@Afzal2143 жыл бұрын
I also check his dc supply in device. And there supply is 18-20 v dc. Can you suggest me any idea for solve this problem? Please
@markgestadavid3 жыл бұрын
@@Afzal214 after replacing the device did you use wiring test or wiring recognition? And reprogram the system?
@markgestadavid3 жыл бұрын
@@Afzal214 well in esser you cannot just rely on voltage you also need to use software to pinpoint the problem, maybe it has loop open or grounding fault
@shimaaatef-f6x Жыл бұрын
How to connect FACP With PC
@shimaaatef-f6x Жыл бұрын
to monitor the system
@markgestadavid Жыл бұрын
You need the software, email me for details. Markgesta@outlook.ph
@Afzal2143 жыл бұрын
How we solve cable fault in esser iq8 control pannel?
@markgestadavid3 жыл бұрын
You need to restart the panel i,if it is still with cable fault,you need to diagnose thru software. You can email me for support markgestadavid@gmail.com
@المجاويميلود3 жыл бұрын
Comment télécharger un programme ? Esser
@markgestadavid3 жыл бұрын
English please
@jkabayan1052 жыл бұрын
sir paano mag by pass ng device kung suspect ang device salamat sir
@markgestadavid2 жыл бұрын
Need mo alisin and device sa loop at base para magtuloy ang loop wire
@jkabayan1052 жыл бұрын
@@markgestadavid pag inalis ung devive automatic by na un sir
@markgestadavid2 жыл бұрын
@@jkabayan105 hindi, kailangan mo syang i wiring recognize at mai program ang panel, pag na overwrite na ang panel at maisend mo ang program na wala na ang device dun palang magiging successfull, means mawawala ang fault sa panel. check mo pa ibang video ko para magka idea ka pa, thanks. dont forget to subscribe.