HOW TO CODE YOUR BMW USING NCS EXPERT | WINDOWS 10

This video will explain everything you need to know to code your BMW using NCS expert as well as a tutorial of what is involved.
PLEASE CHECK OUT MY UPDATED VIDEO: • The EASIEST Setup Guid...
DO THIS AT YOUR OWN RISK. I AM NOT RESPONSIBLE FOR ANY DAMAGE TO YOUR VEHICLE.
Don't forget to subscribe, like, comment
K +DCAN cable (Used for E series): amzn.to/3aLaw9J
LINK TO STANDARDS TOOlS: mega.nz/#F!zw5...
LINK TO NCS DUMMY: www.bimmerforu...
LINK TO NCS PROFILES: drive.google.c...
LINK ON HOW TO BRIDGE PINS 7 & 8: www.e90post.com...
LINK TO ALL CODING OPTIONS E46: docs.google.co... This description contains affiliate links. If you buy a product through my custom link, I will earn a small commission at no extra cost to you. This video is for entertainment purposes only. Evan Goyuk assumes no liability for any repairs or modifications performed by the viewer as a result of the information contained in this video.

[@davedammitt7691]

For those getting the 'VIN not found' or whatever it says error: I ordered the exact same cable from the exact same seller. I was getting frustrated and about to give up. I watched this video over and over, deleted and redownloaded the software a couple of times (is 'redownloaded' a word?) and then I remembered that Evan repeatedly said: "make sure that pins 7 and 8 are connected". Same cable, same seller, same switch setting, right? Nope. I took the clear connector apart to verify that the pins were connected, and noticed that the wires were connected on the right. I moved the switch to the right, and bingo. Immediately connected. Hope this helps someone. Try all 4 switch settings if you need to.

[@z06king]

moved what switch? I have the blue connector apart, and see no switch. Pins 7,8 are soldered together.

[@EvanGoyuk]

Some cables have a switch for different BMWs and some cables are soldered to just work on like the e46, e39, e38

[@z06king]

Ok thanks Evan. I’ll keep trying

[@homeluangaphay2801]

Can you help me I think I screwed up my ecu

[@EvanGoyuk]

What were you trying to do?

[@BryanChance]

This is a great tutorial. There are a bunch of other videos but this one you did is straight forward and easy to follow. Thanks Evan. Oh the reason the folder name is NCSEXPER without the T is because when this program was written back in the days, the filename was limited to 8 characters.(That's what i read in my computer class. LOL )

[@camaroiowaguy23]

after so many videos. this is the one that worked for me 100% first time. i bought a toughbook online from a buddy with ncs all that installed. had no ncsdummy. i followed your video and got it and got it working. thank you a whole lot! :)

[@EvanGoyuk]

Glad you enjoyed it

[@Robertsonfamily219]

Thanks man. I'm a complete nube at this and before your video, I found it incredibly difficult to find the programs, install them correctly and work out how to use them. You not only provided ACTIVE links to the programs and files but you walk through everything in detail and in layman's terms. You have no idea how appreciative I am. Thanks heaps!!! Now I have to search the net to find out how to fold in my mirrors on remote lock on my E70 and change the cruise control display from mph to km/h and hopefully display a digital speedo. Hopefully there are people out there who explain in simple terms as well as you have.

[@TheChedley]

WARNING for first time NCSEXPERT users: It is very important that you save the current original configuration of your BMW car (the FSW_PSW file) BEFORE attempting any coding. So that if you mess up , you can revert and restore your car's original configuration, and not disable it.!! So at minute 20:35 of this video : Stop everything, open another window and make a backup copy of the FSW_PSW trace file, (call it FSW_PSW.backup), then proceed.

[@zezom3341]

The FSW file in the desktop?

[@TheChedley]

@@zezom3341 ---> The FSW_PSW trace file is located in the work directory of NCSEXPERT (typically C:\NCSEXPER\WORK\FSW_PSW.TRC)

[@zezom3341]

@@TheChedley wow thanks alot for replying 5 months later haha If you wouldn't mind could you explain to me where to put the backup as i'm not very good with computers

[@TheChedley]

@@zezom3341 You save the backup copy somewhere you can retrieve it if needed. Maybe on a thumb drive, or another computer, or the desktop, or a memory stick.....

[@adan2lo]

I wish I read this ccomment before I started... Seriously no one one should be uploading tutorials of using NCS Expert without disclaiming TO BACK EVERYTHING UP - you're fucked if you don't. thumbs down for this video. Imagine if I took you sky diving without teaching you how to deploy the backup chute. Still appreciate your effort and time for the video but man. We have to have each others back

[@TheWarewolf79]

Awesome detailed video...Thank you soooo much for that! I just fixed my airbag/seatbelt issues in my car! Why 20 dislikes when this video clearly deserves like a million likes! Thank you once again buddy!

[@mistahaych9552]

Same here i just did mine today and i feel like i'v just won a million pounds. Thanks to this guy. Brilliant video

[@daniellamas647]

Great jobs Sir, I tried to understand something in this BMW matter with many, many hours behind Google and Mega searching ... Now, the BMW curtain is open and I can progress on new BMW coding challenge. Everything is ready to do without spending any euro for the thiefs in the desert. Merci beaucoup. I will be very happy to meet you in next videos.

[@flippy9133]

just a tip if you have problem with the cable driver, the automatic update didnt work for me so I switched to manual and selected the bimmergeeks folder you unzipped and it found the correct driver in there.

[@CaptJofaz]

You are an absolute legend, thank you

[@jozseffloriantorma4155]

Huge thank you to You man!!!!!🙏🙏🙏🙏😎😎

[@johnt.klotsos]

Thanks Evan. Your video helped me a lot to disable TPMS in a 2009 E90 M3. I have no iDrive and used the following code using NCS Expert and NCS Dummy (version 0.6.0.9) along with physically disconnecting the RDC cable connection from the module in the rear passenger wheel well above the battery: CAS Select ECU Module = KOMBI KOMBI: RDC_ALIVE - nicht_aktiv KOMBI: RDC_VERBAUT - nicht_aktiv KOMBI: RDC_DISP_SWITCH - nicht_aktiv KOMBI: MMI_ENA_RPA_RDC - aktiv KOMBI: DSC_MIT_RPA_CC - aktiv CAS Select ECU Module = M3DSC MK60_M3: RPA - aktiv

[@EvanGoyuk]

Awesome glad to help!

[@georgeharrison5793]

Thank You! This is exactly what was needed a step by step guide with possible reasons it wouldn't work. I tried doing all of this a few years ago and gave up. I spent 2 weeks tinkering every day. After watching your video I immediately went out and read a module, made changes with dummy, and will code the module tomorrow! You just saved me hundred of dollars to deactivate the AHL system on my 650. Again thank you!

[@abluh12]

I’ve been searching for a perfect tutorial this is it

[@EvanGoyuk]

Thank you!

[@johntoon3982]

This video made it super easy to use ncs expert an dummy. Was able to code some stuff on my mini cooper. Thanks for sharing your knowledge of the software.

[@EvanGoyuk]

Thank you for watching!

[@horacegrant1615]

This is the best tutorial on coding I have seen ,thank you! Informative and detailed information in an easy to understand way. All the links work as of today.

[@EvanGoyuk]

Thank you!!!

[@Jo_Ro_Fulfil]

Excellent tutorial. Convinced me not to mess with the coding.

[@Lettered_Routes]

I've been looking into buying an e46 for awhile and between your review of the eonon radio and this content Its convinced me that I can buy an e46, get a raw and visceral enthusiast experience while also being able to have modern creature comforts. Thank you so much for putting out these videos. Keep up the great work!

[@EvanGoyuk]

Thank you!! Let me know what other videos you would like to see.

[@llllPROTOCOLllll]

Running this on Win10 without issue. Recently coded and activated my E60 530i Bluetooth. Make sure you update Daten files if you run into Coapi errors during coding. Great video.

[@EvanGoyuk]

Make sure pins 7 and 8 are bridged on the inpa cable

[@EvanGoyuk]

Yes

[@llllPROTOCOLllll]

Make sure you're using the latest daten files for your model. They must be loaded into the software. If you don't have the daten files, you can get the package you need from (Bimmergeeks) the latest version on the site is 60.1. I used it without issue. Once you download the daten files you'll need to load them, the easiest way is with the BMW CODING TOOL. Make sure you update Daten and WinKFP. Search for some videos on youtube, I believe there are a few good ones that walk through how to update the files with this tool. Once you've downloaded the file for your model from BimmerGeeks, and updated try your coding attempt again. You shouldn't get the Coapi error. The reason the error happens is because the Coapi process file is pulled from WinKFP by NCS expert, if NCS expert can't find the file (in WinKFP), it throws the Coapi error. Hope this helps... Good Luck!

[@darek4488]

Having bought yet another E-series BMW this is exactly what I need.

[@miniyatendra3724]

Hi, I have been watching your videos for a while now, finds the videos very useful regards specifically to e46. I have a 4 door 320d 2005 production. It is a base model and at times it is frustrating when you miss basic things like a drink holder or even an aircon which are now standard equipment saying that, still love the car have it since 09 and have 95K miles on the clock, looking at your videos there are endless possibilities to make it look cool and perform better though it is a time consuming but I enjoy it.

[@EvanGoyuk]

Thank you for watching and it is odd that BMW didn’t add these basic features

[@martymeyer4125]

Thanks for taking the time to produce this.

[@mgtow5336]

Totally agree. I reckon Evan would have taken 4+ hours to make this video for us. I love people who share their knowledge.

[@dujevideka1230]

+1 on the generosity and patience

[@deadassbeats1925]

excellent video your explanation was clear and concise, you've earned a new sub! keep up the great work

[@hannya29]

I was getting the vin ERROR until i closed INPA and flicked the switched. (you need to do both) Thanks for the video it was very helpful!

[@firehawk6230]

Left or right ?

[@hannya29]

@@firehawk6230 all the way to the left

[@EvanGoyuk]

Left

[@testIsuru]

this is a Great video well explains everything should know as a beginner, thanks for that, and wishing good luck for future content creation even after 5 years 😄.

[@mrjirey]

Great video instructions. I have done all the setup and validated that the cable is connecting, but I always get a VIN Mismatch every time I go I do the chassis selection for my 2003 e46. I have the exact same cable as yours and I have tried it with all 4 switch positions and all 4 chassis types. Any help would be greatly appreciated

[@JackRR15]

For the module you choose in NCS Dummy it's actually written in NCSexpert which module number it is under the JOBNAME

[@spucky6662]

Finaly something that works!!! Verry usefull tutorial!!

[@bolarobric]

Great share Evan- really appreciate this video and the links. Anyone who needs some of the links I can share these to you. I am waiting on my cable and will try to code out my AFS and the Service reminder.

[@bgfrdqf44]

Thank you for taking the time to share all these informations 🙏

[@andreamitchell4758]

thanks Evan great video i saw the one from 50's kid but i don;t think he knows about compatibility mode in windows ,he was going through the trouble of running a virtual machine

[@mikedodd9294]

Best NCSExpert video on KZbin, thanks!

[@agh6651]

Nice one m8... just wanted to reset my airbag light after kids pulled the socket out from under my seat, loads of interesting info , I may have a go @

[@whadimirquintanilla6655]

TYVM!!!! Excellent Video! I was able to communicate with the DSC and resolve my DSC coding issue.

[@timdeng7303]

Great information and video, I was able to code out the corner leds in my 08 e92 335xi. Thank you so much

[@iMovieXL]

Tim Deng dude, how did you code an e92 with this, there is no option in ncs for any of the e9x’s I have an e90 and ncs expert shows e89 then k1x, how did you do it please?

[@WizRumburak]

Jesus, you are good at explaining! Thank you very much!

[@EvanGoyuk]

Thank you for watching

[@ConcreteJungle7]

Great detailed information. Thanks man 👍👍👍

[@ncpoloboy]

Omg it worked thanks for the video now i have visuals when I lock and unlock and the lil clown nose blinks

[@dtc1117]

Just started looking at your KZbin articles. MASSIVE information! I am very interested in the coding tutorial. I have many questions but I will ask two for now. First, do you have a tutorial on coding using a MacBook Pro? Second, do you offer, for a fee of course, one on one tutorials for people who are REALLY not tech savvy? I have an 01 325CI convertible that I would love to be able drop/raise the top, off my key fob! I look forward to your input and am going continue watching your KZbin's.

[@EvanGoyuk]

All my tutorials are on my MacBook Pro. I have not done any sessions on tutorials. What specifically do you need help setting up windows? If your not tech savvy I recommend buying Carly or the smartTop module

[@kamilozw86]

Finally I found all in one place. Great job. All is going how he describe. Thank you. Polecam wszystko idzie tak jak opisuje

[@loopster40]

CAn you tell me how to get the E90 folder for NCS Expert? I need to code the VIN to my ABS module. And the E90 option is not there for the chassis.

[@loopster40]

@@coco11118 Thank you buddy!

[@davechesney2733]

Cheers for your hard work sorting this out

[@argirov83]

Hello,Im trying to change my e39's LCM2 with LCM3,but it is not happening.The blinkers and high beams are off. The new module is processed with Pa soft so the Mileage and VIN are matching. I have read tons of info,but still nothing. Any help will be useful.Thanks

[@EvanGoyuk]

You then have to code it in ncs expert too

[@JUNGHO15]

HI, Evan, I followed up your instruction to install it, why the NCS-EXPERT open it, after F1+F3 , do not indicate FG and FA NBR , that is only Chassis E70 come out. I check software, do not find the SP-DATEN. Whether or not some where miss the software or others. according to your mentioned as below : quote: I modified my D-can cable and installed a switch in order to have it operational with 2006 and earlier models that use the OBDII port. My cable did not come with an adapter... 2/2007 and older vehicles requires the pin 7 and 8 to be bridged to work..3/2007 and later requires pin 7 and 8 to be separate. So for 2 bucks at Radio Shack and about 20 minutes of my time, I have a fully functional cable for both applications! : unquote: my car is BMW X5 2012 WHether or not D-CAN PIN 7 AND PIN 8 SHOULD BE SEPARATED , I CHECK IT , YES. IT IS SO WHAT CAN I DO , PLEASE HELP ME POINT OUT WHERE IS KEY POINT? THANK YOU

[@Eurosmithpro]

Been at this for weeks. This stuff is never as easy as it looks on the vids. lol Sure hope somebody who can help chimes in.

[@EvanGoyuk]

What do you need help with?

[@AldiShuli]

Hi Evan Goyuk. Thank you very much for the video. Following the instructions I was able to install properly std tools and inpa can see when k dcan cable is plugged in the pc and when ignition is on. Now my problem is when I press "info" button in inpa software in the ini path, ecu path, and interface I see lots of ??????????? Is yours doing the same? Any replay will be much appreciated.

[@Unit974]

The problem with INPA 5.0.6 is that it's not fully english, for example error codes is in german. Do you have any solution?

[@dannyspalding8639]

Hi Euan, Great video walk through. Quick question, my GM3 module went faulty so I replaced from a donor car. Would I now have to use NCS EXPERT TO code it to factory or is factory not VO ie…… folding mirrors when in reverse etc….. and is back to basic settings? Do I click process car? I hope this makes sense. Look forward to your reply 👍

[@PRAGEETHKARUNADHEERA]

Very informative video. Thanks. I could code an E46 323CI after following this just fine. However the E46 M3 remains unchanged. No errors though. Coding gets finished just fine. I already did an SMGII tune using MSSTuner so there must not be an issue with the K+DCAN cable. I need to try it again tomorrow fresh.

[@Duffman__]

Great video! Thanks for recording it and sharing, it's by far and away the most step by step intro to coding I've come across. Since you are using macbook pro, would you advise a virtual machine or bootcamp for those of us that will also be using a macbook pro? or is this software indifferent in that regard? I've got the intel processor chip (i5) for reference.

[@EvanGoyuk]

To be honest I use a VM and have had no problems. But I assume boot camp would have similar results

[@omarbarri3516]

My windows 10 computer comes up with an error when trying to run St212 and says program only works on xp professional, even after compatibility mode, why is this

[@pamdondeli2729]

Can you make a series of different coding and including swapping ecu of an other car, for all of the e46- e90s

[@mlyon89]

I need help with coding out my TPMS system on my E90... im in UK. And on NCS expert....the $2vb in FA/VO isnt there at all that every1 has been deleting to get rid of thr tpms light. I have unplugged the Module in the trunk. My cable also flashes then the light goes out after i get as far as reading the CAS ecu to see the FA/VO codes. Any help much appreciated. It is a purpose built cable i purchased specifically for INPA and NCS.

[@EvanGoyuk]

Message me on Instagram @evangoyuk

[@JUNGHO15]

HI, Evan, I followed up your instruction to install it, why the NCS-EXPERT open it, after F1+F3 , do not indicate FG and FA NBR , that is only Chassis E70 come out. I check software, do not find the SP-DATEN. Whether or not some where miss the software or others. According your mentioned as below: quote: I modified my D-can cable and installed a switch in order to have it operational with 2006 and earlier models that use the OBDII port. My cable did not come with an adapter... 2/2007 and older vehicles requires the pin 7 and 8 to be bridged to work..3/2007 and later requires pin 7 and 8 to be separate. So for 2 bucks at Radio Shack and about 20 minutes of my time, I have a fully functional cable for both applications! unquote: my car is BMW X5 2012 I CHECK the cable PIN 7 and PIN 8 is separated . please help me where is wrong? thank you

[@alanharrylal1670]

This is a HELLA great video!!! Excellent job! You were extremely thorough and made everything easy to understand. I am reading this in 2020 and I want to code some stuff on my 2008 E92 335i. I did not see e92 chassis listed in the list on NCS Expert. Do I just need to get the latest NCS Profiles?

[@willyeyds]

update on this would be amazing

[@dipanman]

@@willyeyds Yeah, as you can see, he never replied to me.

[@EvanGoyuk]

Choose e89

[@dipanman]

@@EvanGoyuk Thanks brother!

[@deborahthompson9525]

Awesome video. Worked like a charm on my 2006 E46 convertible. Thanks. I do have a couple of questions I hope you can answer: 1. What module do I need to access to synch memory seat position to key remote? 2. Is there an option to have doors unlock upon upon removal of key from ignition? Thanks again.

[@emrekyan1249]

Hi did u find any solution about auto unlock ?

[@steveh9946]

Hi bud, great info in your videos. I have a 2002 X5 E53 4.4i that i have somehow changed the comfort entry. the one click door open, two click all doors open is cool and works, but now when i put the key in the ignition and go to position 2 to start it, the driver and passenger widows wind all the way down. The door control switches wont allow the windows to be put up at all until i switch the car off and use the "hold centre button" to close all windows. Any help would be much appreciated as it's a pain in the arse not being able to raise the driver or passenger windows while driving, especially if it's raining....cheers

[@EvanGoyuk]

Message me on Instagram @evangoyuk

[@shooraja]

Thankfor the great video but you did not mention what are the files on your desktop prior to you unzip BimmerGeeks Standard Tools and ncs-Dummy

[@anthonyhughes6763]

Links are hidden in description (pressed little dots and found them eventually!) 1) how do I access/read/check/remove parking brake code errors as I’m getting the dreaded ‘parking brake fail’ message on dash? 2) how do I register battery replacement? (2011 Bmw x5 e70) Many thanks

[@EvanGoyuk]

Link in the description

[@evanormous6409]

Hey man! Great video. Wondering if there is a way I can turn off bulb out warnings. I’ve built some custom tail lights with LEDs and don’t want to run a load resistor due to space and also the heat they generate. Looking online there’s not a lot of direct info on where to find it.

[@2012isRonPaul]

does it work via the older obd1 port too and where is the google drive files ?

[@kevinmilner1762]

Excellent video, thanks so much for your help mate!

[@damirbegic250]

Thanks for video and links in description!!

[@JapaneseMonster]

Can you help? I keep getting VIN is faulty message. I have tried different cables, every position on the switch but always get this message.

[@EvanGoyuk]

Sure message me on Instagram @evangoyuk

[@mejbarron]

Real clear explanations!

[@rambito16]

Thanks so much for posting this video!

[@alexedward1250]

Nice job making the video. I was wondering if you can assist me with a question I have. In NCS Dummy , how do I add an option to one of the choices in the trace file. For example in CAS module, in battery coding, how do I add an option for a 92ah agm battery. I hit on one of the choices which was 80ah agm and right clicked, then selected add an option, but then I don’t know how to populate the boxes below for this choice to become part of the trace file.

[@gingerbadger]

Great vid. Thanks for refreshing my memory!

[@David-rm2zd]

Great job, very informative. My question is what if you wanted to do a used module? Would you read the original, copy all the coding in notepad, put in the replacement one. Open in notepad, delete what's there and paste the original coding info?

[@Kendstudio]

I’m using the files from the description and i’m noticing that ERROR codes in INPA are only in German.

[@davedammitt7691]

type into Google to get translations.

[@androidandroid9591]

An excellent video, for those of us that are starting to use INPA and the rest of the software. However. After installing the software following the instructions here, I get all the INPA diagnostics in German. I left all the tools in a folder on the desktop called BMW TOOLS, and moved the translations.csv file there, but yet the diagnostics are not translated. Should the .csv file be located somewhere else? Txs for the help

[@donrondel8240]

very helpful & clear tutorial.. Thanks

[@curtisbrechter5620]

Thanks for the great video. I'm getting ready to code my Mini R55 Clubman. You're a big help!

[@gustavopaschoal7882]

Hello, I have a bmw e36 323ti 98 and it was trying to encode and when I try to copy the file from my gm4 module it gives the following error message: "error at changing zcs"

[@UdoVali]

Hi, Evan. I have what you can call an uncommon issue. A while ago I used ISTA-P to update all the modules in my BMW 520d E60 09/2007 (pre-LCI I think) with the "magnificent" N47D20A engine. I used an ICOM Next A+B+C which worked flawlessly for me. All good until it reached the last two modules, which were the CCC and the Bluetooth. Somehow the jump lead from the battery got disconnected during programming and both modules mentioned went to "Programming Mode 12" or something and until I figure it out I couldn't use the screen, listen music, etc. The "funny" part (well, not that funny, though) is that I couldn't find ANYWHERE the codes for these two modules, and by "codes" I mean the numbers shown in WinKFP to describe the modules, which in my case were VIRTSG91 - (Bluetooth) - 9176842 and MMI/CCC - (The CCC module) - 9176841. Somehow I used another version of CCC, which actually is allowing me to use the screen, but apart from the music list, there are NO WORDS shown on the screen. The Bluetooth is still in Programming Mode and I couldn't activate it no matter what I've tried. Do you have any clue of where I can find those ZB numbers to match those I have? Any idea would be much appreciated. Best regards, Valentine.

[@kalibsima1450]

Unfortunately you said that the power had been disconnected while rewriting to the dme. if you don't have the original programming then the chances are high that you won't be able to recycle it and you'll technically have to 'unbrick the module' or buy a new one and calibrate it in via INPA.

[@foamuno]

What version of Windows are you using? 32 bit or 64? I have managed to read and code some ECU´s, but I can´t read GM5 or the RLS. I was wondering if it´s because I´m running the NCS on a 64bit Windows or maybe the Daten files are not up to date. My car is a 2003 E46 320D. Thanks for the video, helped me a lot, keep up the good work!!!

[@yeisonnduran]

I want to see your light control module how you have your settings ...

[@alexrustam2677]

Can you please tell me how to code the roof on e93 to open and close by key fob I will be thankful to you

[@colincrosby6422]

Evan thanks for taking all the time to put this up. I have 2000 e39 528i. I think the ABG module is going to have to be replaced for F0 internal fault and also 11 power supply. I was going to get a used one on ebay to save $$$. Could you please tell me, will this program work with this car? If so what is needed to code the ABG module? Any KZbin links? Thank you

[@EvanGoyuk]

Yes winfkp is what you most likely need

[@colincrosby6422]

@@EvanGoyuk First thank you for replying. What is WINFKP ? Do you know if the Airbag module has to have my Vin coded into it? I found a used one from the same model and year, part number and version. I was thinking maybe plug and play? Do you think it would have to be sent to an Airbag Reset service first?

[@spurgeonstapletonjr.7002]

Great video! I look forward to trying to change the code on my e90 to activate bluetooth audio capabilities. My main question is how you're running Windows 10 on your macbook?

[@EvanGoyuk]

VMware fusion I used to install windows 10

[@spurgeonstapletonjr.7002]

@@EvanGoyuk You should definitely make a video on that or show me how.

[@rameshm2100]

thanks for detailed instructions. Is this process the same for szl and airbag/communication module? and do you know what abbreviation is used to identify these 2 modules

[@ThaHammieJaassee]

question when i connect my e82 to inpa it says DME LOCKED how do i unlock it? some other guy told me that i can only do that with ista/p but when i use ista/p i get the import vehicle order

[@dannyguyon9025]

Hi, any ideas why after coding my abs module dxc on e53, i still have the trifecta of lights and brake light is still red??? Please help

[@lozedwards1231]

Hi Even Had to change the ECU, ABS pump and the cluster in my E46 M3 due to a fire in the engine bay! Any ideas how I can change the FGSTNR so they all have the correct VIN number for the car? Also need to do any coding thats required for them to work and talk to each other etc, can this be done with INPA or NCS Expert? I also have PA Soft but a lot of my options are greyed out so maybe I'm only running a demo version or something? Also have a Lew fault which I think just needs the steering angle sensor to be calibrated which I think I can do on INPA Any help would be great Great tutorials by the way Loz

[@kdao1007]

Hi I have 2009BMW 128i convertible E88 - been getting the misfire cylinder 6 a lot. Have replaced all Ignition Coils, All fuel injectors, Spark Plugs. Still get error codes misfire cyclinder 6, DTC 29D2, 2E29, 2E1D, 29D9,

[@danielandreiciurean1928]

Hello. Yesterday i have done a retrofit on my e65. Comfort seats with heating and cooling. Doesn't seem to work so do they need coding? My car didn't had this functions before. Thanks.

[@candicedownard9939]

I have a issue with my down stream 02 sensors. I was told they could be coded out? Ever heard of this before??

[@aimized1460]

Is there any options for enabling the aux ? My aux is greyed out and I cannot click on it. I have 328xi 07 idrive ccc bmw.

[@Jet3ch]

INPA ignition circle is not black but i can still read codes and look at everything. Is that bad?

[@EvanGoyuk]

Are you in position 2?

[@SorinPatru83]

I don't find e90 on choose CHASSIS section, I have a e91, please help.

[@EvanGoyuk]

Choose e89

[@vonboyage]

Does it code the car or the key? Meaning if you done this- you programmed the key to unlock the hood then somehow un synced your key with the car (im talking about when you are synching the car to key for unlocking the car from fob) if you un synced this does this wipe the programming of the hood.

[@derekkchung]

What is coding? Programming? Flashing? Say if I am replacing the airbag MRS module, it is flashing? Here in the video, coding is just changing the optional settings for the module, like one touch all windows down. INPA is to just test the cable and ignition on? NCS Dummy is just a translation from german to english. TRC file is when u read. MAN file is when u write? They are both just txt file. What is profile? A looking table from VIN to all the factory modules? Yes, I am still so confused. I don't want to just follow the step by step instruction. I want to understand the concept and the overview.

[@richardc2637]

This is good Evan! Video provide a foundation to kick start my motivation to learn NCS coding for 2014 X1 E84. I went to your link to place an order on K+DCAN cable and will explore around. For chassis on X1, should one select E89 or E90/E92? Any guidance you can provide would be greatly appreciated.

[@EvanGoyuk]

E89 if not option for e84

[@arkadydushatin6276]

cant switch comp8 to comp1 everytime i press ok, it loads, closes window, and when i re open it, it still says comp8, any suggestions?

[@EvanGoyuk]

Is there anything currently using port 8?

[@tonylou8424]

hello Evan goyuk I did the update but why is it when I go to GM5 C01,C02,C03,C04,C05,C06. I am getting this message a RED( X )15:45:29 An error occurred while reading "C:\NCSEXPER\WORK\FSW_PSW.TRC": Unresolved parameter keyword "500ms" in function "HUB_VERZOEGERUNG_FH_VORN". Make sure chassis and module match those of the trace file.knowing I have had GM5 C01 & C06 working befor but now all of them are not ?

[@pedrocramez]

Hello, I changed the catalytic converter to my E39 year 2000 and the battery had turned off a few hours after I set it all I started the car and it asks for a code of 4 digits but I never got code now everything works but the screen can not choose tv or navigation nothing is in position 1 but after connecting nothing works thank you some help from you because I followed your tutorial and I already have the glasses to work with the keys thanks

[@jonathonhayes5200]

Hi, Got a cable with 2 position switch. I've tried the switch in two positions and installed exactly as you demonstrated in the video. When running INPA, I get the cable detected set to YES, but the ignition flicks incredibly fast between on and off. When I try to run any sort of scan I get IFH-0009: no response from control unit. Any ideas? Driving me mad. Thanks.

[@EvanGoyuk]

Could be a driver issue or a bad cable

[@jonathonhayes5200]

@@EvanGoyuk Gutted. I think the driver is OK; I've tried the driver Windows automatically locates and also the one provided on the disc that came with the cable. I'll therefore assume it's a bad cable. Annoying. Thanks for the videos - keep up the good work. Maybe one day I can do some diagnostic and coding work!

[@EvanGoyuk]

Use my cable in the description. It’s the exact one I have

[@jayvo0713]

Hey I was working on my 2011 Mini Cooper s and all of a sudden when I was using ISTA/p to do some programs for the SZL or SLZ. As it completed now I getting a vehicle order missing. I can’t read any modules or the vin. Plz help

[@3kojones]

Hey man! Really great video, thanks for sharing! I have one question tho. I already have ISTA+ 4.22.4x installed on my system, installing the above will in any way interfere with my already installed ISTA+ instance? Appreciate any reply in case you see this message!

[@EvanGoyuk]

Yes it could interfere

[@3kojones]

​@@EvanGoyuk Alright, thanks for replying! Have a good one!

[@leonardotomasoninardelli]

Hi, this cable work with BMw 320 2015? Please, answer me. Please, help me. Tks

[@WeAreCarFans]

Great tutorial, thank you!

[@htnsys8509]

HI I am using window 10-64bit and it seems everything install corrected. As I verified, Everytime I plug/unplug USB K+DCAN and see usb serial port (com1) appear/disappear. Also "Battery and ignition is black dot show" But none of winkfp/NCSexpert/INPA will pop up messages "IFH-0003 DATATRANSMISSION TO INTERFACE DISTURBED Program will be stopped " Any idea what K+DCAN missing configure here? I even tried to different COM X then other will not make "Battery/ignition black dot" NOTE: trying to re-flash FRM footwell corrupted.

[@pjpan6326]

Hi Evan. Very informative video! Thanks for posting. A quick question. Do you think the K+DCAN IPNA cable you posted would work with a 2013 F30? Thanks for your time.

[@EvanGoyuk]

Yes

[@pjpan6326]

@@EvanGoyuk Hi Evan. I received my K+DCAN cable today and tried to follow your video to open up NCS Dummy and noticed that there was no F30 in the Chassis list. What should I do?

[@EvanGoyuk]

There may be an updated version for it