Everything Steering: Installing and Bolting In the Complete steering setup | ’29 Roadster is MOVING

In this episode we mock-up and test the steering. We bolt in the steering box. Install our drag like and cross steer shaft with our original early style tie rod ends. We even decided to try out a steering stabiliser and create and small mount that looks like it shock be there. Attaching the steering wheel and moving it side to side gives you a small bit of gratification knowing you’re a step closer.
Join this channel to get access to perks:
/ @bennettscustomsco
Shop ➡️ www.bennettscustomsco.com.au/...
Instagram ➡️ bennettscus...

[@ericargo9157]

With your extreme attention to small details you are no doubt destined to be one of the worlds greatest custom builders...if you're not there already. Well done...again, Jordan.

[@bennettscustomsco]

Thank you kindly Eric, still a lot to learn and create to get any recognition but it’s been a fun journey to be apart of this wild addiction

[@joecioe8566]

Great job, I love the front end, the single offset fog light, the crossmember, headlight bracket and the British Columbia plate makes it all look great. I really like the way you don't want it to look like an afterthought and take the time to make it look like Henry Ford made it in 1932. Look forward to the next video.

[@90FF1]

Yes! Everything about the car puts a smile on my face. I love the practical approach rather than being over engineered.

[@bennettscustomsco]

Thank you kindly guys. Means a lot. It’s fun to create these pieces that will be over looked. They are my favourite

[@robertwilson8767]

🦘🇦🇺 Looking good Jordan 👍🏼 I love the way you "Antique" your brackets & fittings

[@bennettscustomsco]

Thanks Rob!

[@timr.3108]

You're really getting me hooked on making the piece look cast with that needle scaler. Nice work.

[@bennettscustomsco]

Give it a crack! You will have a new love affair

[@62_C10]

The amount of effort you put into your work speaks for itself - well done

[@bennettscustomsco]

Thanks kindly Bob, Dad told me never to cut corners unless I’m racing

[@gregjobson4844]

There wont be much flex in the cross shaft and drag link now, looks good Jordan. The needle scaler does a good job aging items, the BC plate looks old on the screen... very handy for aging repairs etc. Cheers Greg

[@bennettscustomsco]

I definitely have a love affair with the scaler at the moment

[@daleking8529]

Man that looks killer! also really like the headlamp setup especially the one fog lamp!

[@bennettscustomsco]

Thanks Dale! Much appreciated

[@franciscoflores7911]

You and Bellos are my favorite KZbin builders.

[@bennettscustomsco]

Thank you kindly! Bellos is one extremely talented man!

[@SchysCraftCo.]

Congratulations. It's coming along nicely so far. 😮.really likeing this project. Can't wait to see more videos soon my friend. Keep up the great craftsmanship and hard work my friend. Fab On. Weld On. Keep Making. God bless.

[@bennettscustomsco]

Thank you Jared! Always great to see your support

[@grumplegarage875]

I like the fog light on the front spreader bar. I think it looks better than a horn would.

[@bennettscustomsco]

I’m with yeah!

[@garyfairbrother5532]

I like your fog light idea better than the badge but wish the cool bracket was just an inch or so shorter…but then I feel silly even suggesting anything to a talented guy like you. That’s gonna be one sweet ride, for sure.

[@bennettscustomsco]

I definitely agree, I had planned on shortening it slightly

[@waynegilling6048]

Front end looks great. Rear suggestion; shorten the horns about half way to the trunk, use the spreader bar as a mount for you spare tire , hinged let or right so easy access to the trunk.

[@bennettscustomsco]

They will definitely get shortened forsure! No spare tire but a few other ideas 💡

[@darylthexton2287]

Looks great,really awesome detail!

[@bennettscustomsco]

Thanks Daryl

[@paulblack2402]

Great work again Jordan . Look foreward to more of the same. Well done

[@bennettscustomsco]

Thank you Paul!

[@BoxcarsGarage]

Sure hope that sway bar gets proven.. I'd add that to my rigs.

[@bennettscustomsco]

You and I both!

[@BoxcarsGarage]

@@bennettscustomsco and that bracket turned out Tits!

[@johnkranz4004]

Nice job Jordan on the bracket looks great

[@bennettscustomsco]

Thanks John!

[@staypositive6984]

Awesome👍

[@FatManLeather]

A leather trunk may look kinda cool mounted to the extra frame in the back, just a thought.

[@stevebulach5198]

Hey Jordan, Love your attention to detail & the tricks to get the aged look. The screw up tie rods were on the early Holdens as well, like EH (1964 back) I just cannot remember if they were threaded on like the one's you have...... Keep up the good work. Cheers from Northern NSW 😃👍

[@bennettscustomsco]

Good to know Steve I’ll have to have a look at one next time! Thanks for the tip!

[@goodevins9408]

So creative your skills are epic! Loving your content and vibe my dude! 🙏🏼🥳

[@MrLangleylad]

Hello from back home ! The car is looking great , you’ve got a great eye for design Jordan .

[@bennettscustomsco]

Thanks Mike! Hope you guys are well, summer looks like it came early!

[@MrLangleylad]

@@bennettscustomsco It's been beautiful , I'm loving your channel buddy. Cheers

[@paulhebbard2138]

the wrap boys on you benny,ya mate does some amazing work al.put me onto it .wish you all well

[@MASI_forging]

That work not easy but our did very well.👍👍

[@bennettscustomsco]

Thank you sir!

[@timferriss905]

Adding the plate and rivets has made a dull bracket into a finished piece. If you have a 36 wishbone, what year is the axle?. Thanks Jordan, another quality film.

[@bennettscustomsco]

It’s a 36 axle aswell, hope to replace it with a 32 heavy at some point

[@craigwilson4439]

Has the 92 year old steering box got enough adjustment left ? . Or will you reco it, if parts are available ?. Nice roadster mate.

[@bobhalstead1879]

Jordan have you thought about trimming the extra length from left steering arm.not needed on right hand drive

[@bennettscustomsco]

Yeah I will, or maybe put something inside the hole hahah

[@andyvoytko]

I wonder if the needle scaler has the same effect as shot blasting?

[@bennettscustomsco]

I think the use of both would be the perfect receipt

[@craigwilson4439]

It's made for getting slag off the the difficult low hydrogen welds. Or any slag from welds in general, and of course scale. We just knew it as a needle gun.

[@erniehoffer1784]

Pedals. Talk to Lee. He just finished his pedals and brakes.

[@bennettscustomsco]

Next weeks video! They are all finished up and working! It’s coming together!

[@EdwardDockery]

👍🏼👍🏼