Bike Rack Taillights - Added safety when your vehicle lights are covered.

[@evolutionaryTom]

Most people don't read the comment section. Here's the link if you're interested. amzn.to/2SP0SsJ

[@reneasselin2598]

Very good video! Did you figure out the cables management?

[@jbalote19]

Hello! Thanks for the video. Can you please also make a short video clip how the lights works during daytime, please?

[@jrb737]

Hello, how are your lights holding up? I've gone thru 2 sets after barely even using them. The left side light on both sets either stops working or only partially works. Meaning it will come on w/ headlights, but not the blinker or brakes. I had U-haul test my connection and it is fine. The lights worked great when I installed them.

[@marciarobertson3622]

Sincere thanks for this video! I’m a 70 yo woman and was able to add the needed lights! The EZ Fold may be expensive but I can get my bike rack on and Lectric bike on by myself!

[@evolutionaryTom]

You made my day, MarCia!! Thank you for the nice compliment. -Tom

[@jonathanseyfert8256]

Thank you for being considerate to your fellow drivers! I see so many people with bike racks with the bikes blocking their signals, driving down the interstate without a clue nobody can see them or their signals. Not to mention the trailer, oh gosh the trailers where they can’t spend 30 seconds doing a simple light check and lights don’t work, partially or at all. Or the one trailer I saw with REVERSED turn signals, when he put on his right turn signal the left trailer signal flashed and vise versa… This is great. I plan to get a bike rack soon and was looking for ideas on lights so I don’t do the same. I’m not a huge fan of how dim the turn/stop is in relation to the running lights on these particular signals, so I’ll look for other ones for myself, but even so it’s 1000% better than the no turn signals I usually see around here.

[@Finnegan6674]

I have the same problem and have been looking for trailer lights that I could install easily and this is what I am going to go with. Thank you so much. It was driving me crazy.

[@randylundquist8816]

Awesome video. I have been looking at zillions of alternatives to add lights to my rack. Your method is by far the best!

[@evolutionaryTom]

Thanks, Randy. I wish they were even brighter but this is a huge improvement.

[@Index-o1234]

I agree same here I purchased a 1up but wasn't happy with there license plate holder Led light and I thought it abit expensive there had to be a cheaper alternative that makes you happy with a license plate AND a Brake and sjgnal light at less then half the price 1up was offering.

[@AC-dk3ve]

Thank you so much Tom for sharing this video. This product is indeed the best one after my hours of web searching. And your idea of apply velcro is brilliant.

[@evolutionaryTom]

I really appreciate the nice comment, Alexander. I was just commenting to someone from Canada yesterday, and how my trip there was cancelled this month. Can't wait to get back. I've been asked for a video on how to do the cable management with those lights on the hitch. Might be doing that soon. -Tom

[@thevantuyls]

Thank you, Tom, for the informative video, and for your replies to people's comments and questions. After reading your replies, I ordered some D-Line Cord Covers and Bongo Ties for cable management. Great video.

[@erikavolltrauer8549]

I just asked about these lights on your previous question/answer video. Thanks this was very helpful!❤

[@zgarcia51]

Brilliant! I been looking (for many hours!) for a more versatile and cost effective way to light up my cargo carrier. I also needed someway to store the carrier and not have its lights damaged. Your solution is by far the best. Having the parts list and links also saved me time. Thank you!

[@evolutionaryTom]

Thanks, Luis. I'm glad it was helpful to you. That makes my day. -Tom

[@agnesf2659]

Thank you soooo much for this! I bought exactly the same light kit in Canada but use 3M dual lock tape instead for even stronger adhesive strength. The CURT 53201 auxiliary led indicator lights kit is a great product that brings no hassles to me who is not a handyman at all. All the cables are long enough for any regular rear bike rack and cargo carrier.

[@evolutionaryTom]

You are welcome, Agnes. I'm a big fan of the 3M tape also! I hope it all works for your setup. -Tom

[@TheMiddle-formen]

Tom - thanks for this video and answering my question. As it turns out, I had used the exact same product on my Hollywood rack. One thing I would caution about with this product is that because the LEDs draw very little wattage, the wires are incredibly thin. Mine were defective right after I installed them the same way you did. They’re easily pinched when folding the rack etc. I just ordered the same rack you have and will use the same lights again as everything else is too bulky. This time will run the wires through a narrow piece of automotive plastic flex conduit and be careful not to let it get pinched. Your content is great and thank you! Gary

[@evolutionaryTom]

Thanks for the tip, Gary. I love learning from others who have done their own hacks. Thank you very much. -Tom

[@davidwiniger3799]

Great idea on the automotive conduit what size diameter?

[@TheMiddle-formen]

Hi David - almost any auto store such as O'Reilly"s or Autozone sells this stuff in all diameters down to 1/4" or 5/32' and either one will do nicely. Cheers

[@hoosierinthewoods]

I cannot thank you enough! Your video just saved me hours of work!!! 😊

[@thundergunn]

Great video. Waiting for delivery of my ebike rack. Definitely going to install these lights.

[@reevesproductions877]

Wanted to say thanks for the video, I did mine the same way and I love it. I also ordered extra plates when traveling long distances just in case.

[@evolutionaryTom]

You're very welcome. Thanks for the nice comment. -Tom

[@ceciliaholcombe818]

Thank you....looked at several configurations and like yours the best and so appreciate the video. Ordered mine today. Strange no one locally have it in stock, but that's ok. I DO read the comment section...haha Thank you again. Cely in Cocoa Beach, Florida

[@evolutionaryTom]

Thanks for the nice comment, Cecillia. We just moved to Marco Island, FL. I haven't checked out these lights in the bright sun yet but I will soon. -Tom

[@simontemplar3379]

Thanks sooooo much for putting this all together. Really appreciate it...

[@evolutionaryTom]

Thanks for the nice comment, Simon. Much appreciated!

[@Opine.Social]

Please provide a picture on how you routed the cables

[@EileenHall-c1w]

How about video on putting on a license plate with lights on the Thule rack ? Can you hook it all up to the same wiring cable?

[@nealskelton1425]

Thanks Tom. By the way, I really like your cardboard targets.

[@Mr1drumlover]

Thanks much Tom for this very helpful video. We can now travel much safer with our ebikes on the Thule EZfold.

[@rudyespada9324]

All the videos I watched in regards to the Thule EasyFold XT2 really made my decision!!! Love your reviews and now the light kit. Thanks again for the info. I only wish I can find the EasyFold as cheap as you did

[@evolutionaryTom]

I hope you find some kind of a deal, Rudy. Thank you for the nice compliment. I really enjoy hearing from people that the videos have helped. -Tom

[@EileenHall-c1w]

How did you manage the cables? Video please

[@KtotheL]

thanks for taking the time to share i love your workshop as well btw awesome bro.

[@evolutionaryTom]

Thank you, K to the L!! I really appreciate the nice comment. -Tom

[@xolomartinez6036]

As soon as I put that e-bike rack and bike on the ram, I got rear ended twice in a few weeks.

[@dannyspleen]

Thanks for this Tom! Will be doing exactly the same installation today; really appreciate your video.

[@evolutionaryTom]

Thanks for the nice comment, Dan. I appreciate that!

[@davidwiniger3799]

Did you ever make your wire management video on this rack?

[@GadgetBoyea]

Great idea, Tom. I just purchased two Ebikes and have this same concern with my break lights. Can you post a update showing cable management?

[@evolutionaryTom]

I'll put that on my list, John. I'm working on one now showing the new optional XT ramp for the EasyFold. Thank you for the idea! -Tom

[@markmori1521]

Awesome who made the harness? Great job!

[@jeffdurling100]

Have those same lights. Great for the night but not near bright enough for the day.

[@evolutionaryTom]

I would agree with that assessment, Jeff. I wish they were brighter in the daytime. -Tom

[@wrenchdoozer]

Excellent video. Now that you are two years into this setup, has the velcro held up well in varying weather conditions?

[@mikehammer4546]

Great idea, I did basically the same on my fixed rack motorcycle/ebike carrier

[@evolutionaryTom]

Actually, it should probably come with lights. We'll see how they last, Mike.

[@justicecenter]

Installed my lights today

[@adamschorr7240]

This is so helpful! Quick question: How beneficial is the velcro versus just using the existing 3M adhesive tape?

[@evolutionaryTom]

Thank you, Adam. I think the 3M tape would work just fine. I've found no need to really remove the lights since I came up with this. I think you'd be good! -Tom

[@adamschorr7240]

@@evolutionaryTom Thanks!! I might also want to use this rig on another hitch carrier I have. But to be honest, the LED is around $25 and I might just buy another set.

[@jackiehorn3724]

I really like this tail light solution. In California I have been pulled over twice for no tail lights on the bike rack, and also, my license plate on my Ram Promaster conversion van is covered up by my bikes, and the last officer reminded me that when I moved my plate I needed to make certain it also has a light. So....until I figure this out, I am not able to take my e-bike out on my van...frustrating....I dont know why they do not put these required items on these expensive bike racks in the first place.

[@evolutionaryTom]

That's pretty frustrating, Jackie. I hope this idea helps you. You are correct, it should be integrated into the design in the first place. -Tom

[@dianewomble527]

Great video. Thanks for sharing the product links.

[@zoody1000]

Great video ! so much to helping to understand this item I just ordered , Thank youi

[@evolutionaryTom]

Glad it was helpful!

[@haroldstone9360]

How did you secure the wires on the rack?Or did you just remove them after each use?

[@swizzzlestik]

@evolutionarytom Thanks for the video Tom, this is exactly what i was looking for. How well does the velcro tape stick over time with the elements? I'm looking to use this both when the rack is up and when it's loaded with bikes and velcro strips at different locations using the same light bars are exactly what I was looking for.

[@evolutionaryTom]

The velcro has held up really well. Recently I did a video on another light bar and I think it can be adapted to the Thule rack in the same manner, with the velcro. It is very bright and easy to see in the daylight. kzbin.info/www/bejne/rGKkfZKhjM9pn8U Both are better options than no lights at all, for sure. Thanks for the nice comment. -Tom

[@swizzzlestik]

@@evolutionaryTom Thanks for that link and video. I am weighing my options now. I have a Saris MHS platform and Saris makes a light bar that is specifically for MHS racks and has a bracket that uses existing bolts and bolt holes to secure light bar to rack and is $40 more than Hollywood. The only downside is the Saris bar can impede your legs a bit while loading on the bikes.

[@alberthilt]

Update on your taillight installation??? Any suggestions or things you might have (or have done) differently?? Great video by the way.... I bought the same rack, and I am going to install the same light as well. Thank you!

[@evolutionaryTom]

Thanks for the nice comment, Albert. I haven't done anything different, it's still working great as is. The best way to manage the wire is just a zip tie. Since it's not a permanent fixture on my vehicle, taking it on and off should be as easy as possible for me. That's why I just ruin one zip tie at a time with the wire management. -Tom

[@justicecenter]

Tom how did you end up routing the wires? I have purchased the same lights.

[@evolutionaryTom]

I used stick on cable routers, the kind you see in the office stores, not the hardware stores. Then I can snap the wire in and out as needed. I route it strait to the plug and the excess I bundle up with a Bongo Tie. Works great. -Tom

[@reneasselin2598]

Very good video! Did you figure out the cable management?

[@connietraines9409]

Thanks for the informative video....would you provide a link to the source for the taillights. Thanks

[@evolutionaryTom]

Here you go, Connie. amzn.to/2N8euN6 Thanks for the compliment! -Tom

[@emorypowell2919]

Nice find

[@raulapa]

Great video! I followed your advice and I bought an XT-2 and the LED tail lights. I installed the wiring harness myself and ... the driver's side of the lights does not work. Any ideas? suggestions? troubleshooting steps? Thanks to all in advance.

[@evolutionaryTom]

raulapa, I can't think of why they wouldn't. Must be defective lights. They are such basic wiring that I can't think of anything on your end. -Tom

[@raulapa]

@@evolutionaryTom thanks Tom. To be on the sure side I'm doing some tests with my multimeter

[@raulapa]

@@evolutionaryTom I bought a basic 4-way flat connector tester. It shows a fail on left turning light problem. When brakes are applied, LED lights work OK so, problems seems to be the wiring harness/Converter. My re-seller is contacting Curt to see what they'll do.

[@johnj2803]

How long is the cord from the lights to the plug to your car?

[@evolutionaryTom]

Probably 4 feet, John. Enough to where I have to coil it up multiple times to take up the slack. -Tom

[@davidemanuel2528]

Where did you purchase the light kit?

[@evolutionaryTom]

amzn.to/3RRQM8h It's this one, David. -Tom

[@admissionsaaron]

I have a 4 bike rack--how long is the harness? Want to make sure it will be long enough.

[@evolutionaryTom]

You would need an adapter, Aaron. It only comes with a 4 pin standard spade plug.

[@AC-dk3ve]

I bought this kit from a Canadian website. If you check this product review video by e-trailers on KZbin, he mentions the harness is 71-inch long, and left/right module is 22-inch long. To me that's pretty long enough for a Thule T2 Pro XT 2-bike setup.

[@evanwindom3265]

The wire from the 4-pin flat connector out to the splitter is 71". Each of the lights has another 22" of wire. Image #2 on the Amazon product page gives the details. If you need extra reach, you can buy an extension cable for the 4-pin connector. Here's a link: www.amazon.com/CARROFIX-Trailer-Extension-Female-Connector/dp/B07QPPT6X9/ref=sr_1_3?dchild=1&keywords=4+pin+flat+harness+extension&qid=1597284014&sr=8-3

[@ronaldramsey7774]

Great video..thanks for sharing.

[@justicecenter]

I don't understand why they didn't make the USA version with light like they did with the European version.

[@evolutionaryTom]

I totally agree with you, JC. And for the price they definitely could have included it. -Tom

[@davidmillan2057]

now that’s what I’m talking about

[@evolutionaryTom]

Thank you, David!

[@longrange9818]

Where are the signals and license plate? İt doesn't look like legal.

[@evolutionaryTom]

LR, the lights are also signals and brake lights. The rack has a location in the middle of it where you can put your license plate as well. -Tom

[@longrange9818]

@@evolutionaryTom thanks for your answer.

[@davidwiniger3799]

Never came back and showed how you hid the light wires. Looks awful wire mgmt wise in a few later videos and now you have moved on to other racks.

[@evolutionaryTom]

I still have my Thule rack and use it. I commented below somewhere that I never found a good way to do the wire management other than wrapping the excess around the hitch post and eating up the long wire that way. -Tom

[@share4power673]

I watch this video to find out where u connect the light to the car but it’s not there . Don’t watch this if ur looking for that

[@evolutionaryTom]

It's just the standard 4 way flat trailer plug that connects to the car. It's at the end of the wire to these lights. You just plug it in.