ExpressLRS Radio Link System - Low Latency and Long Range | ELRS Nano TX Module

Latest releases of OpenTX www.open-tx.org/downloads
Update the OpenTX firmware oscarliang.com/flash-opentx-f...
ELRS lua Script github.com/ExpressLRS/Express...
ExpressLRS project github.com/ExpressLRS/ExpressLRS
ExpressLRS configurator github.com/ExpressLRS/Express...
2.4 Ghz RF module: bit.ly/3DTUvek
Nano receiver: bit.ly/3DOUN6i
900 Mhz module: bit.ly/3DUNycX
and it's nano receiver: bit.ly/3yZscaZ
BetaFPV web:betafpv.com/
ExpressLRS is an open-source RC link for RC applications. It is based on the fantastic Semtech SX127x/SX1280 hardware combined with an ESP8285, ESP32 or STM32. ExpressLRS supports a wide range of hardware platforms as well as both 900 MHz and 2.4 GHz frequency options.
Join our Discord server: / discord
Website
joyplanes.com/
Become one of us:
goo.gl/zKQ706
Facebook
/ joyplanesrc
Instagram
/ joyplanes
#JoyplanesRC #HobbyRC

[@CarbonGlassMan]

I'm looking forward to getting this module in the mail. I've had a big Crossfire micro module hanging off the back of my Frsky x9lite radio for over a year now. This module will actually fit in the bay on my radio. The price of the receivers is way better than crossfire. The money I spent on 3 crossfire receivers will get me 6 ELRS receivers. I do feel kind of like I'm cheating on my wife though. Crossfire has never failed me and it's protected all my quads by never failsafing, but I'm going to set it aside and start playing with ELRS. I do hope that this will not hurt TBS very much. I hope they can adapt and continue to innovate and make great products. All they'll have to do is lower their price if that's possible for them. By now the high prices should have recovered all of the R&D they put into developing Crossfire.

[@nolansneeder]

Awesome video! Do you have any recommendations for resources on setting up a budget FPV system? I’ve thought it would be fun but the amount of options can be a little overwhelming! Looks like you’re having fun!

[@MultiTech-es3ou]

I might buy it

[@salihimere2989]

Hello, I think your video is super good. I have a HappyModel EP1 ExpressLRS 2.4GHz receiver and would like to set the VTX table in Bethaflight, but it cannot find it. what should I do?

[@LordFpv]

Great tutorial,can you tell me where i can find this 3d print stl for module?

[@nutsnbolts4601]

Hi what’s ur advice on connecting to Rc car with ground control 🎉

[@pateachongthu]

to exit out of lua, simple press and hold exit/return button for 2-3 seconds. atleast it works on my qx7

[@Joyplanes]

Thanks for the advise!

[@ajianto445]

You should het 1 million subs my word

[@reorklp7428]

can u make a video on how to use 4 wires brushless motor

[@saurav3000]

👍👍👍

[@yoanariosuwandito8711]

i have jp4in1 module, what protocol is best for less latency?

[@kayezero703]

جميل

[@EastenRobert]

👍

[@indradarmansyah7733]

Are there applicable for a cheap tx such flysky fs-i6? (With rx fs-ia6b)

[@Joyplanes]

No, hardware has to have specific chips to work.

[@CapungPlastik]

In case you missed it. There is firmware mod for flysky i6 & i6x that compatible of expressLRS modules. I have couple of videos about it too. :)

[@christopherleveck6835]

I've been using OpenLRS for years. Will my hardware work?

[@Joyplanes]

I'm not sure, but it's cool you've been using it for long.

[@SeeFPv-qm6ie]

it won't flash on my module it says error in red

[@funnflyers6894]

Nothing could beat crossfire. Record on 25 mw and stock antenna is 50 km. You could switch up to 2 w of power and the Antennas you could also change.

[@Ludo---]

Hello long push to return

[@clsgaming3859]

how to buy that

[@Joyplanes]

Updated in the description 2.4 Ghz RF module: bit.ly/3DTUvek Nano receiver: bit.ly/3DOUN6i 900 Mhz module: bit.ly/3DUNycX and it's nano receiver: bit.ly/3yZscaZ

[@derrogers]

afaik lrs doesn't comply with lbt rules in Europe

[@7royalseven7]

dosen t care , greets from Germany

[@technicaldavelazer9151]

Tried to be the 🥇 first comment 😃 but someone beat me to it

[@sherandaleemexpress7098]

tried to be the 2

[@JLsMakerSpace]

First