How To Make An Epic Buildup Scene On the Octatrack

[@EZBOT_]

Don't forget to subscribe and join the discord! discord.gg/KUSBH9h Lessons and contact: ezbot.live Support this channel by joining the Patreon : www.patreon.com/ezbot

[@videosarchive8058]

You’re killing it so hard with these videos man I can’t even tell you how much I appreciate this truly inspiring thank you endlessly. This video is such a banger.

[@_justin_joe]

Keep this series going! So insightful and helpful to see how you are building these amazing effects and showing the endless depths of the OT!

[@EZBOT_]

Thanks Joe!

[@esotericmusicmachines8136]

Thanks so much for your ongoing development of this wonderful instrument!

[@pyronb]

Summary of parameters and everyhing : // FX Chain on Drums channel - T1 FX1 Delay: LOCK: ON TAPE: OFF FB: 127 SEND: 127 B LOCK: SEND: 0 TIME: 128 - T2 FX1 Filter: All defaults B LOCK: BASE: 64 WDTH: 14 Q: 40 - T2 FX2 Delay: FB: 80 B LOCK: FB: 80 SEND: 80 - T2 LFO1: PMTR: FLTR WDTH WAVE: RMP TRIG: TRIG SPD: 16 B LOCK: SPD1: 16 DEP1: 50 // FX Chain on Melodics channel - T5 FX1 Delay: LOCK: ON TAPE: OFF FB: 127 SEND: 127 B LOCK: SEND: 0 TIME: 128 - T6 FX1 Filter B LOCK: BASE: 60 WDTH: 10 Q: 40 - T6 FX2 Delay: FB: 80 B LOCK: FB: 80 BASE: 40 WDTH: 80 SEND: 50 - T6 LFO1: PMTR: FLTR WDTH WAVE: RMP TRIG: TRIG SPD: 16 B LOCK: SPD1: 16 DEP1: 54

[@HanjoSynth]

So cool Matt, thanks for sharing the detail walkthrough!

[@thomasvandendool6613]

amazing vid again :D exactly what i needed to understand the workings of your templates a bit better, thanks!

[@curtainsinmotion]

Thanks a lot for these videos dude. So insightful, cleverly explained and so inspiring!

[@externalcontrol]

efextive vid ;) Thank you!

[@EZBOT_]

You’re welcome

[@draconianrhythms]

Masterclass … Thank you EZ ❤

[@suntzu6122]

KZbin really dropping the ball on recommending me your vidjas sometimes. WTF KZbin

[@EZBOT_]

Agreed!

[@koalemos1679]

One thing I learned about freeze delays is if you set it to a small number, I had set it on 1 once, it will pop and click when you try to use a scene that sets it to zero to initiate the freeze. I hope that makes sense.

[@EZBOT_]

I do this all time with no pops or clicks

[@koalemos1679]

@@EZBOT_ I have a MKI, do you think that could have something to do with it? I was able to repeat the issue. Maybe my OT has seen better days 😭

[@EZBOT_]

@@koalemos1679 is your OT the master clock?

[@koalemos1679]

@@EZBOT_ I’m pretty sure it is because I think you mentioned that it can cause issues if not. I’m using it with the Electribe 2 siblings. The synth just gets clock and the sampler gets clock and notes. Synth is leads and pads, Sampler is bass, and OT is drums/mixer fx.

[@EZBOT_]

@@koalemos1679 hmm, try using the tape delay, it’s less prone to clicks

[@patrikkonat3085]

Video is really good and as always pedagogic. I do have a question. Why do you have a 303 attached to the side? You have a dual VCO in Syntakt. Is it not as good?

[@EZBOT_]

Different sounds than you can get from the Syntakt

[@tacticalgrooveorbit2379]

when you use elektron devices on 8 bars, how do you do for eight, Sixteenth note?

[@EZBOT_]

Trig length takes care of that

[@tacticalgrooveorbit2379]

@@EZBOT_ yes but if you have few notes following each others sixteenth notes?

[@EZBOT_]

@@tacticalgrooveorbit2379 Microtiming, I see where you are going with this but I only use 8 bar tracks for tracks where it makes sense, otherwise I'll use 4 bars

[@tacticalgrooveorbit2379]

@@EZBOT_ ok thanks 👌