In this video we show you the tips and tricks on how to make and perfect an owb kydex holster
Пікірлер: 89
@ryco18658 ай бұрын
Thanks, I made holster for my Taurus I'm proud of after watching your vid.
@crypto_pinto26604 жыл бұрын
Well thanks to this video I may have found another new hobby on top of my leather work
@papadozaemm49913 жыл бұрын
Where did you get your spool of spacers?
@straightup9373 жыл бұрын
Nice job dude..!
@shaunb51263 жыл бұрын
I'm liking your videos. I think it would be interesting to see a dual gun, small of the back, palm out, IWB setup. Preferably for M&P 9 2.0 Compact 3.6" guns. 😉 What are your thoughts on one of those as opposed to two separate holsters behind the back?
@FalTacUnlimitedLLC3 жыл бұрын
One of my very first holsters was a taco for 2 fnx 45s for small.of back lol there's a couple ways to go about it. You can form it and make one holster. Or you can make 2 separate holsters and use a backer to connect them which allows them to flex as well. If I were to do that again, I'd go for the flex for user comfort
@triumphmanful3 жыл бұрын
learning all I can before I make my first holster. What is the reason for all the blue tape ? Can I set rivets without a press ? I have tools to set rivets in leather. Can I use them for Kydex ?
@FalTacUnlimitedLLC3 жыл бұрын
Blue tape sets the kydex off the firearm so it doesn't scrape. Gives more room. You can set rivets without a press but it's more of a pain and cumbersome
@loushackelford7283 жыл бұрын
How would you work a holster set up for a gun with a thumb safety?
@phoenixholsters Жыл бұрын
What size rivets are you using to accommodate for the belt clip hardware?
@FalTacUnlimitedLLC Жыл бұрын
8-10 Eyelets on everything
@tanawat2543 жыл бұрын
Colt cobra 22lr please.
@kyleolsen1764 Жыл бұрын
Can you vacuum press, an outside the waistband holster?
@FalTacUnlimitedLLC Жыл бұрын
Yes. Taco and pancake style. Newer videos have them
@rohnek22 жыл бұрын
Hey Brotha man, im new to holster making, with the press, i have that same foam, does it matter which side you use? one side is slightly different in texture than the other?
@sfcasarez5 ай бұрын
What are you using there on that spool for your retention spacers?
@FalTacUnlimitedLLC5 ай бұрын
Part number 65112 on amazon. Continental washer and overflow tubing
@bmf572 Жыл бұрын
SAR CM9 (ie CZ close w/ambi safety)?!?
@netmag2002 Жыл бұрын
What thickness of kydex do you use?
@FalTacUnlimitedLLC Жыл бұрын
.08 for most.
@netmag2002 Жыл бұрын
@@FalTacUnlimitedLLC in inch or cm?
@FalTacUnlimitedLLC Жыл бұрын
@@netmag2002 inch.
@netmag2002 Жыл бұрын
@@FalTacUnlimitedLLC many thanks 🙏
@IGROKStream4 жыл бұрын
what material do these pistol models ?
@FalTacUnlimitedLLC4 жыл бұрын
Fiberglass/aluminum reinforced resin
@bricefsvens50313 жыл бұрын
What kind of laser engraver do you use?
@FalTacUnlimitedLLC3 жыл бұрын
20 watt raycus fiber
@jimlong80913 жыл бұрын
Honestly, I thought I was the only person that dropped everything a dozen times or more during my projects...
@FalTacUnlimitedLLC3 жыл бұрын
Don't you hate that hahaha
@brice76494 жыл бұрын
Do you get all your hardware from knifekits.com?
@FalTacUnlimitedLLC4 жыл бұрын
About 99% of it sometime diy
@lof13203 жыл бұрын
🇧🇷
@karapusat40023 жыл бұрын
V💀nd⚰tt⚰
@mikejohnston5159 Жыл бұрын
Where did you pick up that rivet setter? Not the press, but the actual two piece thing?
@FalTacUnlimitedLLC Жыл бұрын
They have the at holstersmith.com and diyholster.com I have a set of each.
@shortmag4294 жыл бұрын
another great vid Iggy, i learned a few things i'm going to try on my own OWB process...
@BamaChad-W4CHD3 жыл бұрын
I can watch these videos nonstop. You are a wizard man. You definitely earned my sub. I'm also glad I watched you making holsters. I would have had no clue why something like added a flashlight fit would cost more. I knew it didn't use extra kydex to make it more expensive. Now I realize the extra work and time put into things like flashlight and Suppressor sights fitting.
@FalTacUnlimitedLLC3 жыл бұрын
Definitely a lot behind it. And thank you!
@mxclr8 Жыл бұрын
did you make the jig for the rivet holes? whats the measurement center to center vertically for the rivet holes? thanks
@dRoPaCiD74 жыл бұрын
So how can I order an owb with an open bottom and 10 degree cant rmr cut and low sweat guard for a g43x like your work
@FalTacUnlimitedLLC4 жыл бұрын
Go to faltacunlimitedllc.com and find the appropriate category. Theres a note section as well. You can add open bottom and 10⁰. And thank you
@BamaChad-W4CHD3 жыл бұрын
His website is freaking great. It has me in a kinda kid in a candy store vibe lol
@kriskomsa50484 жыл бұрын
Nice vid !
@MarktheAirsoftPrimate3 жыл бұрын
Started making holsters a month ago, your videos have been extremely helpful.
@FalTacUnlimitedLLC3 жыл бұрын
Hell ya
@dougdaniels3 жыл бұрын
Great video. New subscriber from MA. Like the SpeedEase option. I'll get some in my next knifekits order 👌
@kellygangnath13992 жыл бұрын
Can you make a Taco style own holster for a glock 19
@FalTacUnlimitedLLC2 жыл бұрын
Of course. Email me at faltacunlimited@yahoo.com
@kellygangnath13992 жыл бұрын
@@FalTacUnlimitedLLC Trying to make it for my sons. One lives in California and the other lives here in Texas. I am just getting into this as a hobby for now. Your videos are very informative and enjoyable, please keep it up. Kelly Gangnath
@FalTacUnlimitedLLC2 жыл бұрын
@@kellygangnath1399 if you need a shell I can form one and send it to you for you to finish. Another service I offer
@kellygangnath13992 жыл бұрын
The question is, have you ever done a taco holster for outside wear or would you suggest a pancake style?
@kellygangnath13992 жыл бұрын
Another question for you, I have a CZ82 . Could you please do a video on doing a taco or a pancake style holster.
@barrymanning81714 жыл бұрын
These videos are the best! Informative plus entertaining, I just placed a order for
@samuelugh57292 жыл бұрын
Wow!!!
@ciscoshibler32143 жыл бұрын
I have watched 30 or more videos on making kydex holster from a whole host of different content makers.i am just getting into making holsters and you are by far the most informative and helpful by far! Thanks so much! Subscribed for sure!
@FalTacUnlimitedLLC3 жыл бұрын
Thank you!
@worldwar3tactical4943 жыл бұрын
Awesome vids! Subbed after 1st vid. I'd love to see u do a full size Desert Eagle 50AE...??
@FalTacUnlimitedLLC3 жыл бұрын
Me too! Done a few. I'll film the next
@johnweinz3367 Жыл бұрын
What thickness are you using? .06 or .08
@FalTacUnlimitedLLC Жыл бұрын
.08 min. I use .06 when I do dual layers and they're both .06.
@rickluchtenburg81664 жыл бұрын
Great job again
@blackcreeklearning20374 жыл бұрын
Great job sir.
@papadozaemm49913 жыл бұрын
Blocking a revolver for owb?
@FalTacUnlimitedLLC3 жыл бұрын
Easy stuff. When I have a revolver coming up I'll do a vid
@pimenteldrew3 жыл бұрын
Nice work. Im looking at making one for my XD-9 with a streamlight TRL-4 on it. Have you made one with that combo yet? Light sticks down past the trigger guard so was wondering how the retention would be.
@FalTacUnlimitedLLC3 жыл бұрын
What size barrel xd9. I have like 4 options. But yeah its the same with every handgun. Block the channels for the light and you're gold
@FalTacUnlimitedLLC3 жыл бұрын
What size barrel xd9. I have like 4 options. But yeah its the same with every handgun. Block the channels for the light and you're gold
@FalTacUnlimitedLLC3 жыл бұрын
What size barrel xd9. I have like 4 options. But yeah its the same with every handgun. Block the channels for the light and you're gold
@rvega917223 жыл бұрын
do yo have any p80 holsters?
@FalTacUnlimitedLLC3 жыл бұрын
Yup. I offer p80s for the 17.19.22.23.32.33. Listed at Faltacunlimitedllc.com
@jndred2 жыл бұрын
new sub here..exactly what i need for my M&P 2.0
@FalTacUnlimitedLLC2 жыл бұрын
Appreciate the sub! I still make these left and right
@jndred2 жыл бұрын
You do a great job!
@FalTacUnlimitedLLC2 жыл бұрын
@@jndred thank you!
@kevinpool97773 жыл бұрын
I love your videos but can you do it with a heat press trying to see what I'm doing wrong thanks
@jackieperot45623 жыл бұрын
Can u do a revolver like a 357 big frame
@FalTacUnlimitedLLC3 жыл бұрын
I'm sure I'll do one eventually
@jackieperot45623 жыл бұрын
10 4 bud enjoy the videos
@bobandrews705 Жыл бұрын
You are a very talented man my friend. Get yourself a KelTec P 17 mold. The gun is getting more popular, especially for us old folks! Let us know I’m ready to buy.
@FalTacUnlimitedLLC Жыл бұрын
i think i have one lol
@danielquinlivan77773 жыл бұрын
Hey Iggy. Great job as always. Where can I purchase the ladder bars? Thanks for your help
@FalTacUnlimitedLLC3 жыл бұрын
Most gun stores carry them. You may also be able to get off amazon.
@93jcoop2 жыл бұрын
Where can I get that roll of tubing you use for retention bushings?