FAN CLUTCH Removal Without TOOL 5.3 Vortec 6.0 4.8 4.3 L How To Remove FAN CLUTCH NUT Holding Pulley

TOOL SHOWN IN VIDEO To Remove Fan Clutch Without Using Special Tool Linked Below
amzn.to/3feN710
Or Use SPECIAL FAN CLUTCH REMOVAL TOOL Linked Below
amzn.to/39wH050
Fan Clutch Removal Without Tool Not Using Special Fan Clutch Holding Tool On 5.3 Vortec, 6.0 Vortec, 4.3 Vortec, 4.8 Vortec V8 & V6 Engine On GM General Motors Pickup Truck, Car, SUV, Or Van On Chevy, GMC, Cadillac, Chevrolet, Buick, & Hummer Tutorial Video Showing How To Remove Fan Clutch Nut Stuck Or To Tight How Do I Stop Fan Clutch Pulley From Spinning When Trying To Unbolt Or Takeoff Fan Clutch Nut When Bolt Just Spins How To Hold Fan Clutch Pulley Belt Slips Or Bolt Shaft Trends Wouldn't Loosen Up How Do You Keep Fan Clutch From Spinning To Loosen Radiator Fan Nut On Water Pump To Take Off Radiator Fan Clutch Without Using Special Fan Clutch Removal Tool & No Fan Clutch Remover Tool On GM Or General Motors Vehicle Brands With V8 Vortec Engine Or V6 Vortec Engine Such As 99, 00, 01, 02, 03, 04, 05, 06, 07 Chevy Silverado 1500, Chevy Silverado 2500, Chevy Silverado 3500, GMC Sierra 1500, GMC Sierra 2500, GMC Sierra 3500, GMC Denali, Cadillac Escalade EXT, GMC Yukon XL, Chevy Tahoe, Chevy Suburban, Chevy Avalanche, Chevy Express 1500, Chevy Express 2500, Chevy Express 3500, Hummer H2, Chevrolet Silverado 1500 HD, Chevrolet Silverado 2500 HD, Chevrolet Silverado 3500 HD, Chevrolet Tahoe, Chevrolet Suburban, Chevrolet Avalanche, Chevrolet Express 1500 HD, Chevrolet Express 2500 HD, Chevrolet Express 3500 HD, GMC Savana 1500, GMC Savana 2500, GMC Savana 3500 Plus Other Makes & Models Vehicles With 5.3L Vortec, 4.8L Vortec 4.3L Vortec, & 6.0L Vortec Engines Or Motors 2020 Instructional Tutorial Video On How To Loosen Up & Remove Fan Clutch Nut From Water Pump Shaft Bolt With No Special Fan Clutch Removal Tool! This video shows how do i remove fan clutch on Chevy Silverado 1500 2500 3500 HD GMC Sierra 1500 2500 3500 HD years 99-07 or 1999-2007 removing fan clutch for cooling radiator mounted to water pump easy, simple, & quick trick on how to do DIY hack for fan clutch removal on Vortec motor or engine in GM vehicles. How to remove radiator fan clutch nut unbolting stuck or tight fan clutch nut when bolt trend shaft just wants to spin or main pulley belt slipping when attempting unbolting fan clutch from water pump this video shows step by step how to hold fan bolt to keep it from turning or slipping to unbolt fan clutch to replace water pump or install new fan clutch. Amazing tip for removing fan clutch nut that is to tight or fan clutch won't come off problem how do you stop radiator fan from spinning or slipping when trying to unbolt fan clutch nut easiest way to do without fan clutch removal tools to hold radiator fan from moving when trying to unbolt fan from water pump to change water pump. This 2020 tutorial video is a step by step instrustal guide showing trick to removing fan clutch nut using no fan clutch remover tool. This video details DIY fan clutch removal how do i remove fan clutch on 5.3 Liter Vortec, 4.3 Liter Vortec, 4.8 Liter Vortec, 6.0 Liter Vortec engine or motor on General Motors GM vehicles such as pickup trucks, cars, vans, & suvs without special tool or fan clutch removing tools no fan clutch removal tools needed for taking off fan clutch on 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, Chevy Silverado 1500 2500 3500 HD, GMC Sierra 1500 2500 3500 HD, Chevy Tahoe, Chevy Suburban, Chevy Avalanche, GMC Denali, Cadillac Escalade EXT, GMC Yukon XL, Chevy Express 1500 2500 3500 HD, GMC Savana 1500 2500 3500 HD, Hummer H2 & plus more years makes & models on General Motors GM pickup truck, car, van, & SUV taking off fan clutch removal without needing to use proper fan clutch removal tool unbolt radiator fan from water pump bolt shaft trends DIY tutorial video 2020! Learn how to remove fan clutch not using fan clutch remover tool. This is instructional video on how to loosen fan clutch nut to remove fan clutch from water pump that cools radiator what to do if nut is stuck or spinning or just spins & won't come off water pump bolt trends pulley belt spins & is to tight to loosen or unbolt without belt pulley slipping problem solved how to take off fan radiator that is tight or stuck removing fan clutch using no special tool solving fan clutch removal issues DIY how to tutorial video 2020! #ChevySilverado #FanClutchRemoval #FanClutchRemovalWithoutSpecialTool
TOOL SHOWN IN VIDEO To Remove Fan Clutch Without Using Special Tool Linked Below
amzn.to/3feN710
Or Use SPECIAL FAN CLUTCH REMOVAL TOOL Linked Below
amzn.to/39wH050

[@toryhowland]

Omg wish I could send you some $ I’ve had to change water pump 3 times in 2 years and no stores have the renter tools in stock you just saved my life from a stressful day thanks man

[@EverydayImTECHnIt]

Glad i could help you avoid a stressful day

[@donaldstepp4850]

Is it because the miles or did you just get the knock off pump?

[@randylee249]

Your pipe wrench looks like a crescent wrench to me. Good video explains a lot.

[@somewhitedude01]

😂

[@TheProfessionalAmateur91]

It’s a pipe wrench because he uses his giant pipe on it. 🤷‍♂️

[@joshuamoore4410]

It's actually an adjustable wrench. Crescent is a brand.

[@SpinninRotors]

The amount of advertisements in the video is ridiculous

[@inverseuniverse5727]

Much more room to work , if you remove upper fan shroud . 4 plastic push pins and 2 10mm screws .

[@NORTAH85]

Unfortunately the “ upper fan shroud” is connected to the “lower fan shroud” thus making it “fan shroud”

[@inverseuniverse5727]

@@NORTAH85 , It is a two piece fan shroud. I own a 2002 Tahoe, Add to that I have been a professional technician since 1981 . I don't know what you mean that it is a one piece shroud .

[@robertthornton5574]

Shroud all in the way I can't work like that

[@craigleslein6844]

its a 2 piece shroud, 4 push pins, and 2 screws and the top section of that shroud is out and out of the way.

[@jordant6666]

Dude. Thank you. I’ve spent hours trying to get mine off and this worked in 30 seconds. Thank you.

[@BigPrada9603]

This video is worth it's weight in gold. Took me one minute man I appreciate this wish I could like it 1000 times💯💯

[@EverydayImTECHnIt]

Thx's glad it helped!!!

[@shaynaphone69]

Use a good C clamp if you have one instead of vice grips on that pulley. Put it around the diameter of the pulley. Otherwise great video. I came here to confirm it wasn’t reverse thread and your video did the trick!

[@robertlee412]

Same...didn't want to be tightening it.

[@victorreyes2135]

Best videos are filmed in the dark of night😁👍👍

[@chelancoy9792]

Thank you so much! I wouldn't have gotten the fan off without the video!!

[@samuelshaffer9566]

My dumb ass took the fan off the clutch 🤣🤣🤣😂

[@erikwichmann3890]

major help! popped the sucker loose before the video was over. thanks

[@Dan-gj1hz]

ur a SAINT! went outside on my LS and it worked second try.

[@robertstell2455]

This worked for me, thank you so much from a gearhead to a gearhead....

[@PabloRHernandez]

Thank you thank you thank you for posting this video!!! I made the mistake of removing water pump with fan and clutch together. I later realized that I had to remove the fan BEFORE removing the pump. by placing the water pump on my bench vise grip and using the the tools you mentioned, i was able to remove the fan. once again...thank you.

[@robertovasquez6208]

That was very helpful thanks cause I'll be doing that work on my truck tomorrow both the water pump and fan clutch

[@jonbollas5870]

You saved me a lot of time. Thank you for posting this!

[@EverydayImTECHnIt]

Glad to hear the video helped!!!

[@lamborghiniregistry]

the vice grips worked perfect to get the fan off my 2010 Dodge Nitro. Thank you

[@darkside0776]

Work like a charm! Thank you!

[@EverydayImTECHnIt]

Glad It Helped & Worked!!!

[@Gansta1o1]

Hey thanks dude. Do not have the tool. Need that fan removed. Didn’t know where to start. U did it. Thanks dude

[@EverydayImTECHnIt]

Glad to hear it helped thanks for feedback!!!

[@yakdriver7580]

Thanks for this video, I’m rebuilding 6.0L motor for a Camaro and I had it off in 5 minutes after watching your video.

[@tyry345]

his "pipe wrench" is and adjustable wrench also known as a crescent wrench in the south

[@hillbillyd4642]

We call it a crescent in the north too

[@kevinc5917]

Best video out there on how to do this,thanks~~~~~!!!

[@ivans3232]

Thanks man. Helped me out a lot A

[@majorflankzz133]

Good idea man, just used your trick today and it worked for me! Thanks

[@EverydayImTECHnIt]

Hell Ya

[@joelsims98]

Thanks for the tip. Worked like a charm!

[@EverydayImTECHnIt]

Glad to hear it helped

[@alangarcia4327]

This was very helpful, thank you very much tho! Love it

[@howardkraemer1833]

Best vid i seen yet thanks keep up the good work!!!

[@epicbagelswag]

Absolute lifesaver of a video! The Chevy engineers must’ve been smoking some good shit when they came up with this one..

[@troylong7472]

Help me out alot appreciate the information

[@aceoutdoors5908]

Thank you this helped a lot

[@mmw78]

Excelent information, thanks.

[@alexr4312]

I tought you had to turn it clockwise nvm then lol thx man you’re vid helped out a lot

[@jasonsavoya1389]

Worked perfectly

[@EverydayImTECHnIt]

Good to hear glad it helped!!!!

[@SeaBound1985]

The link for "tool used in video" 🤣🤣 thanks for the laugh, good vid man. 👍👍

[@Backstage2024]

Thank you it helped

[@austinelperro]

You are a smart man wow I never thought I can do that

[@EverydayImTECHnIt]

If you say so lol i'm glad i was able to help!!!

[@alejandrohernandez9235]

Thank you!!!

[@AngelRamirez-bl4xz]

Great advise

[@daledahlman9629]

Thanks very much

[@JMcMillen1446]

Every video I found so far, including this one, has skipped right over all the other important stuff involved with doing the job. Those of us who are completely ignorant to auto mechanics need that info.

[@Dbeats62]

God bless you

[@donmurrin5269]

Thanks bud. That was a long way around the barn.

[@rick4799]

Great idea, is it the same for putting it back on?

[@emphiaz]

Great video. But sadly don't have grip pliers that have that angle like yours. So still need a special tool.

[@garydylkowski1797]

Very clever to put on that pipe costume on that crescent wrench turning it into a polish-ed pipe wrench

[@jorgevaldes9512]

thank you just saved my life, on a hard day greetings from Mexico City my Friend

[@Memphisgrindtv]

Thanks bud

[@Karmadntmiss100]

Just leave the fan belt on next time put the wrench around the fan clutch nut and just hammer it easiest way I've done those, fan belt helps and then just tap the wrench with hammer

[@Mechanicsville804]

If you don’t have the locking pliers you can also use a strap wrench. They are very cheap and at most auto parts stores.

[@anthonyrodriguez2613]

But nicely explained

[@ChristianRodriguez-lb3qg]

Will this method damage the new water pump pulley when installing clutch fan with new pump

[@spheramid2750]

cool trick

[@garydylkowski1797]

Very clever putting that pipe costume on your Cresent wrench making it a polish-ed pipe wrench.

[@howardkraemer1833]

I know what a Cresent wrench is det dee dee but im watching a vid how to take a fan off det dee dee😂

[@rEVILut1on]

Shout out to all the scars from plastic fans blades

[@travisweible7386]

Y’all never tried smacking a big wrench with a hammer? With the belt on, long open end wrench and hold some tension on it then smack with hammer. It works

[@iooi1181]

i used a doubled up coat hanger... thread it threw one of the holes in the pulley then threw one of the holes in the power steering pump pulley.... tried it single first and the co;at hanger broke, doubled it up and it held.

[@Mike_The_Hog_A_Nator]

I keep everything together & put a big Crescent Wrench on it, then pop it hard once with a hammer. That's Always done the trick for me.

[@BoostedBroz]

If u do it without holding the pulley and it turns will that mess it up sounds like ain’t compression when I did in accident

[@anthonypulliam6092]

Does it come out with the fan shroud still on there? Not sure it would be very helpful to remove it but not be able to get it out.

[@EverydayImTECHnIt]

TOOL SHOWN IN VIDEO To Remove Fan Clutch Without Using Special Tool Linked Below amzn.to/3feN710 Or Use SPECIAL FAN CLUTCH REMOVAL TOOL Linked Below amzn.to/39wH050

[@shrimp8004]

So i can put some heat on it huh i can get it off now I'm worryed getting the seal to hot it's on there pretty good 4 ft cheter pipe didnt get it hardest one yet cant c where did u clamp vise grip on pully itself

[@anthonyrodriguez2613]

You have to position your cameras on a spot for steadilyness

[@XoyaREI]

Did you have to take the hose off?

[@Trple777]

First off never work at night and second if you're already DIY'ing it and saving money then you might as well get the right tools for the job. Just my opinion and I've learned the hard way.

[@pauld7309]

I'm a mechanic, Just did a 03 astro van 4.3. Water pump, fan clutch would NOT break loose. Threw my impact hammer and tool with my torches on it would NOT Budge. So had too ( saw zaw ) it off. NEVER had one as stubborn as that one!! After it was off, my 1/2 drive snap-on impact barely back it off!! Crazy. So morale of story sometimes they won't come off!!

[@EverydayImTECHnIt]

Did that vehicle ever have any front end damage i bought a chevy express years ago i think like a 08 or something at salvage auction from copart & it had front end damage & cracked a few of the plastic fan blades & that thing was a son or mother truckin sucker to get off i think i finally was able to heat it & get it off but was a pain in the ass.

[@pauld7309]

@@EverydayImTECHnIt don't know? It Was a customer's van !! Everything was intact. But man. What a bit#h!! I was killing too much time on it, so no choice!! Usually with the impact too , it takes longer to assemble the tool than to zap it off. Lol.

[@homesold]

When I saw the size of the threads on the new water pump I knew it was going to be fun getting that off. Pointless overkill fastener for just a fan. The old design this replaced was much better/sensible

[@Kickclutch_chris]

It worked!! Took me 3 min to take it off (motor was on a stand)

[@chuchoelroto1318]

Using the special tool, that is the 2 piece set, seemed easier for me to do. The 1 piece special tool sucks. I was able to remove and replace both the clutch and pump in 6 hours. That was my second time doing it on my vehicle.

[@kentontraffie6541]

What are you putting vice grips on

[@EverydayImTECHnIt]

The black deal the belt slips around to turn the fan. Hope that helps

[@hectorluisperezrivera864]

Lol! I removed my water pump with the fan and everything! Was lot easier out of the vehicle. Was removing water pump anyway.

[@SerrAvid]

This works for 4.8

[@MrStephen777]

Yes it may be useful as believe it or not there are no bolts whatsoever on fan clutch assembly. So special tool i just bough is useless.

[@cindylu1cs]

Also that propane thing for soldering copper pipes is called a torch.

[@howardkraemer1833]

No its not its a crack lighter🎉

[@Edster98]

The 6.0 LQ9 doesn’t come equipped with a fan clutch. What else would cause over heating, water pump and thermostat has been replaced, no coolant leaks. both electric fans work, but the temp goes from 195-220 no higher than that any suggestions.

[@LA_Commander]

GM engines tend to run hot for emissions reasons. Those temps actually sound normal.

[@homesold]

I hear the gauge is also inaccurate

[@aaronvilla13]

Didn’t work for me and vice grips left scuff marks but I probly just didn’t get it 100 percent my vice grips I couldn’t get them tight enough maybe.. or last person who changed the clutch tightened it way to much.. that thing is on there tight!

[@EverydayImTECHnIt]

Sorry it wasn't able to help I'm sure that's probably what happened someone must have tighten the shit out of it LOL!!!! Also help to have good pair of vice grips some won't work as well as other's for doin this also. I would try heating up nut with mini propane tank deal like what you use to sweat chopper or soldier chopper pipe etc to heat nut/metal it expands then comes right off not sure if I said that in video can't rember if I did that or not or mentioned it if I did then disregard cuz u already saw that info in video LOL those fans can kinda be a bit of a b**ch to get off at times. GOOD LUCK!!!!

[@joshuatharp491]

What size adjustable wrench is that

[@EverydayImTECHnIt]

I would say medium to large size lol definitely not huge but not really a small one either like medium size

[@lionscott1663]

Help Question I replace the clutch and the water pump and the fan is spinning slow and the water pump is not spinning, van overheat quick not even 3 minutes because fan not spinning fast and water pump is not working, the water won't circulate to the radiador and don't know why ,

[@AttorneyBCollins]

Put your fan belt back on.

[@VShonSummons03]

Your fan goes clockwise so you unscrew the fan left loosey right?

[@LA_Commander]

Yes

[@VShonSummons03]

If my fan spins counter clockwise does that mean I unscrew righty loosey?

[@LA_Commander]

Yes

[@Shooting-gallery223]

Ik how to take off a fan clutch but does anyone know how to take off a fan from the originally clutch so you can still reuse it?

[@REDXIII1331]

Bought my tools from advance for 12.99 with coupon

[@LilElfinmajk]

I mean sure that's helpful if you're fanclutch pulls has space to fit the vibe grips into or behind. Mine doesn't, so this doesnt help

[@mikimiki195]

Use pipe wrench whack it hard it will come off 👍🏻

[@happyman5389]

So yea put this thing here and hold there then yea push on this and yea that's it easy peazy

[@NN-cw9rb]

Goodness gracious how many times are you going to mention there's a special tool? Stopped the video half way through and was already up to 6 times.

[@taylorryan4071]

If I hear tool on more time

[@HeadHoncho352]

Pretty sure that’s a crescent wrench but 🤷🏽‍♂️ to each his own

[@ethans6.0]

when is the amazon stuff gonna stop

[@barrysmith1654]

Not a pipe wrench , crescent wrench

[@runinnhorse151]

You do not know a pipe wrench from a Crescent wrench (adjustable wrench)

[@thomashmoore]

Don't for get to mention counter clockwise to remove. WtF

[@dannyfubar3099]

I'm sick of KZbin commercials destroying what was once a great community. Now every posting has been turned into a parasitic opportunity. BITCHUTE!

[@allensmith3803]

Air hammer with a flat head tip and zap that fucking bolt on the corner and boom it's off wont hurt the bolt puts a small mar in it takes 4 secs to get the blade off worked in a junk yard pulling motors that's how we do it

[@ontheedge4life]

Man I really struggle to get through your video because you Uhmmm.... and ahhh sooo much!

[@EverydayImTECHnIt]

Thank you for your honest feedback!!!!

[@johnnymartinez3745]

Trick only works if you have no belt on the pulley

[@dkrawk8309]

Honestly, always loved driving gm, never owned one or worked on them too much, drive old Ford, and God am I ever happy. Like for WHAT effin reason does gm needs special tools for EVERYTHING? Wanna change ps pump? SUCK it bruh. Good job at micky mousing it, but still, just pita

[@johnhubbard4249]

Next time take the garud off and do it during the day so someone can see something, just a little feedback from a viewer, not trying to dog u out bc those types of things are a real pain, I'm in the middle of it right now. Thank u.

[@Ninjawarlock819]

Pipe wrench huh ? Lol

[@jjspillane1272]

Where I come from that's not a pipe wrench even tho you used a cheater pipe on the tool it's still a adjustable creseant wrench .....

[@Mechanicsville804]

John 3:16 For God so loved the world that he gave his only begotten Son that whosoever believeth in Him shall not perish but have everlasting life.

[@danihz5610]

*came here for actual size on correct wrench* * was never mentioned * Video says without proper tools *keeps spamming click link below 🤣🤣🤣🤣 for proper tools*