Fastway e2™ Trunnion Installation

[@reddawg990]

Thank you for the shorter updated video with the bookmarks for each step. Made the install painless and straightforward. Word of advice to those thinking about tightening their own hitchball to 450lbs, pay to get it done...you're welcome

[@FastwayTrailer]

Glad it helped! Thanks for watching.

[@danielserrano2801]

I see no final step of tightening the angle set bolt with the system under load...

[@FastwayTrailer]

Hi Daniel! We didn't touch on this in our video, you're correct! You can however find the answer to your question in our e2 Trunnion installation guide starting on page 18! www.fastwaytrailer.com/pdf/FW_e2_4.5K-Trunnion-Owners-Manual-2020-sep.pdf

[@danielserrano2801]

@@FastwayTrailer Certainly worth mentioning.

[@Tigers1Girl07]

We just bought a new truck for towing our trailer and the hitch receiver height is higher than our previous tow vehicle. What is the best way for us to adjust our Fastway e2? The original set up was done by the RV dealership and, to be honest, I don’t recall them giving us the installation booklet! I will print off a copy, but it won’t have the initial measurements they may have recorded in the original booklet.

[@FastwayTrailer]

Hi Shelly! I've attached the link to the original e2 installation booklet below. If you have any more questions you can contact our customer service team at (800) 478-557 and they can walk you through the installation process as well!

[@trevorvalentine7721]

To make things easier for those looking for the tools list: For install without the hitch ball preinstalled: * e2 Owner's Manual * torque wrench - 250 ft-lb capable * torque wrench - 430 ft-lb capable * ratchet wrench * 1 1/8" wrench or socket * 1 1/16" socket * (2) 3/4" wrenches or sockets * 15/16" wrench or socket * measuring tape * pencil * 1 7/8" thin walled socket * 1 3/4" wrench

[@silaslongshot941]

How much does this hitch head assembly weigh? Got a 'low capacity lift' backbone here!

[@FastwayTrailer]

It weighs about 45 lbs.

[@disalvofamily231]

Feels kinda like lifting Thor's hammer

[@Joybellmorgans]

I only got a short shank with my kit and just 7 washers. My trailer is not level.

[@ronaldvrbicky5677]

Just curious is it normal to have to raise the pickup up to the point of the wheels almost come off the ground to get the bars on the L brackets????

[@FastwayTrailer]

Hi Ronald, no that is not normal. If you are having issues putting your bars on your L brackets, contact our customer service team at [e-mail] or call them at 877-523-9103 and they should be able to help you!

[@larrywelch4836]

Video indicates start with 6 washers but digital manual indicates start with 3 or less. Which is it?

[@FastwayTrailer]

Hi Larry! You can add up to 6 washers if you need to level your trailer frame. Hope that helps!

[@filup7419]

At 4:37 you say that the appropriate Front Axle Load Restoration (FALR) is supposed to be between 50-100%. The example in your video had it adjusted to 75% but the owner's manual for the Nissan pickup asks for measurements from the front a rear bumpers so it's hard to determine if your setup was accurate or not in accordance with the vehicle's specifications (all other manufacturers use the front fender like you mentioned in the video). That said, at the time of this video (June 2020), the Ford F150 specified a 25% FALR, Chevy at 50%, Ram at 66%, and Toyota at 100%. How come your video makes no mention of this when the manufacturers of these vehicles tested their trucks to SAE J2807 standards (hitch companies do not adhere to them)? Who should I believe when setting up my hitch to keep my family safe when towing my RV through the mountains in the rain or any other conditions, the manufacturer of the truck or the hitch company? Why?

[@FastwayTrailer]

Hi Phillip! The best way to get an answer to your question would be to contact our customer service team at [e-mail] or call them at 877-523-9103!