Few people know this wonderful method electric welding tricks

[@jasonvillarosa7755]

Wow... Nakakatulong po ito sa akin Lalo nat kakasubok lang ako mag school nang Tesda

[@BENGLASBERKAHCHANNEL]

Such welding tricks must be applied in the field, because these tricks are very important to achieve a good goal 4:42

[@THANUT1]

Phương pháp tuyệt vời quá 👍 like cảm ơn bạn rất nhiều đã chia sẽ video

[@ManuelJimenez-ki5bv]

Saludos buenos trucos De soldadura electrica

[@joseantoniosuarez8091]

Te queda mucho que aprender .

[@joeys5429]

What’s the trick ?

[@ГусенАзизов]

В том что труба стоить вертикально без наклонов.

[@Trungcokhi1]

❤❤❤❤❤❤

[@IsleOfFeldspar]

I forgot to put on my helmet before I watched your video now I’m BLIND

[@2strokewilson46]

Pretty ruff!

[@gauravoo7225]

Very Good 👍

[@paulhammersley4562]

where's the trick's,

[@weldorman8495]

Here's a wonderful method. Quit trying to act like a tough guy and put your bloody gloves on - even when tacking. It only takes one good burn to put you out of commission.

[@jorgealvarofernandezacosta4801]

Lo que no veo bien es, que en lugar de hubicar el cilindro primero, y haciendole la correcta mecanizacion.... y luego soldandole las tres alas para esto en la platina.... SIN SOLDAR EN UNA PARTE DE ARRASTRE Y NO DE EMPUJE.... Ya que cuando sueldas con electrodo con escoria y sueldas con empuje... Ñla escoria quedará dentro del baño de soldadura... Algo que no es recomendable....!!!

[@ElFinucho2409]

Con electrodo 70/18 básico, un muy buen electrodo

[@Ahmed-yv5sv]

يافندم الاول كان لحام 6013 بعد كده في اخر المقطع غيرت لي 7018

[@ARTEM_GRINEVICH]

90 процентов сварочного шва на пластине 10 на трубе , катет далеко не 45 градусов

[@renatosoares6554]

You should show the amperage

[@jamessmith-np7yf]

2 big a bead for such thin pipe I would think.

[@gordonmair377]

Learned this on day one fifty years ago ,if you want a big fillet weld use a bigger rod you don’t need to move the rod around to get a perfect weld .

[@hyp.aka4776]

А чё косынки не обварил

[@CarlosHernandez-ij7pl]

Bueno 🎉🎉🎉😊❤

[@samuelashworth8711]

Should always clean your slag off before welding again or else you will get it mixed into your weld...🙄

[@nabeelehtesham3472]

Great

[@yamoya7339]

역시 한국인만큼 용접 잘하는 민족은 없군.

[@joeys5429]

Good note

[@romanbalaz9180]

😂😂😂😂😂😂😂😂😂😂👍🏻👍🏻👍🏻👍🏻👍🏻super komentár.

[@Майор2011]

А хитрость то в чём 😆 !?

[@АлексейРыбаков-и5ы]

😻😻😻😻😻😻😻😻😻😻👍👍👍👍

[@rahmawati7388]

Sudah banya yg tahu itu bos

[@marcoturazza8473]

excellent

[@artiskota9682]

Keren

[@romanbalaz9180]

Nič nového.A pri napájaný by sa malo začať pred zvarom a po chytené oblúka premiestniť k napojenie zvaru.

[@cedricgauthier6380]

Les goussets ne servent à rien, juste à vous gêner pour souder. Rien de particulier.

[@jeanmassoulle1788]

Mauvaise façon de procéder, ont pointe le tube d équerre, ont le soudé,puis les gousser!!!!!😂😂😂😂😂😂

[@darrencrosby4520]

You gotta bend rod for that ??!! Oh my gawd ..,your hands are so jammed in there you look like a dog f in a foot ball .. hold the stinger and weld it .. that isn’t exactly a tricky set of spots .. yes I’m a welder

[@spining2204]

Полностью бесполезное видео. Дизлайк

[@yuosya170]

,💪💪💪🇺🇦🇺🇦🇺🇦

[@djak-u2u]

И че🤣🤣🤣