Not sure if u figured it out yet but the issue with it dying when u put it in gear is the kickstand switch!!
@griffenatekevinbacon4 жыл бұрын
I was just thinking that watching this
@ufoxfox43524 жыл бұрын
You read my mind man👏👏 ,defo a fellow biker you are ,,👍👌✌🚵🚵🚴
@browndog34555 жыл бұрын
It's your safety switch on your stand .stalling when put into gear
@randomvids47555 жыл бұрын
looks good man im gonna be doing the same to mine
@lilmaserati564 жыл бұрын
He needs to stretch the chain bro it to slow thats why it not catching speed
@scottoconnell53095 жыл бұрын
Any way you could point me in the right direction on how to try and get it running
@devonfretwell33514 жыл бұрын
Where did you get the rack and pinon steering
@MrFinkFixes6 жыл бұрын
Awesome build. Awesome to see you finished it too. Only suggestion I would make is swapping out to a wider rear axle for stability. My Yerf-dog 3206 Videos shows my 42" long axle and it kicks the tires out a bit to make it more stable. Do you plan on selling it or keeping it for a trail riding toy?. If your just selling it Skip the axle mod.
@mr.b12596 жыл бұрын
Fink I will check into the wider axle, it definately is too narrow. Not sure if I'll sell it or not yet.
@johnsmithfakename84225 жыл бұрын
I will be honest ... that thing is TERRIFYING! Cool but terrifying. The largest motorcycle engine I would consider putting in one of those karts is in the 50hp area. Anything larger and I would be concerned that the chassis might buckle under the power.
@mr.b12595 жыл бұрын
Absolutely! This thing is a death trap! The frame is not meant for this kind of power, but as long as I dont push it to its limits it should hold up.
@carsonday72835 жыл бұрын
Be more concerned about taking flight lol
@Kyle_gallegher5 жыл бұрын
I don't think that is a major issue u could jus use thick wall piping and make engine mounts from 1/4 inch plate but the basket itself should be fine.
@madis105 жыл бұрын
Very nice build, watched your videos! Can you please explain the gearbox? As i can see there are reverse, neutral and forward. Didn´t see any clutch there.
@mr.b12595 жыл бұрын
The motor/transmission came from a motorcycle. It has 6 forward gears and neutral, no reverse. I did put a clutch pedal up beside the brake.
@Kyle_gallegher5 жыл бұрын
@@mr.b1259 I see so you sized up linkage to what was the foot shift and then added a neutral 'foot brake and just made a jack shaft using welded in pillow blocks and small axle! Nice. I see why you used a motorcycle no axles and trans is inclusive
@vegascolors5 жыл бұрын
Kinda wished you'd shown what it would do to demonstrate the forward power, rather then a bunch of figure 8s
@connerbaldwin84055 жыл бұрын
crazy, I'm planning on doing it to the same exact one because we have a bunch of old shells at the camp I work at that my boss says I can have for free because he'd just have to pay a truck to come get them anyway, this is a taotao 150 targa right? or is it a dongfang?
@mr.b12595 жыл бұрын
Kandi is the brand, but same thing yeah
@OmarRodriguez-xu3lz5 жыл бұрын
it sounds like the carbs choke need work! how it runs now im building a joyner 250 swaping a 600f3 turbo . great job man
@mr.b12595 жыл бұрын
Thank you! I did go thru the carbs a couple more times and got it running much better. Make a video of your build and share it!
@OmarRodriguez-xu3lz5 жыл бұрын
I will love ur built!
@Cr0zzAlpha4 жыл бұрын
Im still puzzleda out the transmission.adding reverese just adding reverse gearbox,so will it go reverese even at 1st 2nd or 3rd gear right?
@DrLove9114 жыл бұрын
Yes if you add a reverse gear box it will go in reverse in any gear. . all it does is switch the direction of the drive spocket.. so if you're in 4th gear and you got your foot on the clutch and you put it in reverse you'll go backwards in 4th gear. Or most likely you'll take off backwards and your engine will die
@Cr0zzAlpha4 жыл бұрын
@@DrLove911 now i want to find out about those new trike model like piagio's with its reversability...im gonna ask our neighbor how it works,if it is what i think it is,it could probably a solution for it.and for a fact those trike climb up hills smoothly for 125 cc trike uhmmm hehe
@YesIFondle5 жыл бұрын
This looks great, I have a few questions. How tall are you and how comfortable is this for you to drive? Also what kind of gokart is this? As in what make and model?
@mr.b12595 жыл бұрын
It's a kandi 150gka-2 I believe. I'm 6'1" and I fit ok. I dont think 2 adults will fit comfortably, but a kid passenger is just right.
@YesIFondle5 жыл бұрын
@@mr.b1259 Thanks for the fast response. Keep making great content and you'll be famous on here before you know it!
@DrLove9114 жыл бұрын
It's also a Tao tao Targa or a spider . The new ones are 200cc the older ones are 150cc . I have an old Targa
@johnathancherry43313 жыл бұрын
U still have the buggy I would love some good pics of how motor is mounted and the rear shaft I have the same buggy and wanting to do a swap
@mr.b12593 жыл бұрын
I do not have it anymore. I do have other videos of the build on my channel, those should answer some of your questions.
@codybuxton6 жыл бұрын
You might check the kickstand indicator. That would cause it to kill when put in gear
@mr.b12596 жыл бұрын
cody buxton it ended up being the neutral switch in the motor. I cut the wire and grounded to the frame, that took care of it.
@codybuxton6 жыл бұрын
Mr. B hell yeah! Nice going man.
@mr.b12596 жыл бұрын
Thanks man. It was fun. I have a couple other builds on my channel, check them out!
@bonezcuztomz77039 ай бұрын
❤how u did the shifter
@Addictraining0074 жыл бұрын
what kind of cable have you use for your shifterd were have you bought it? it would be really helpful of you for my buggy project big tank you
@mr.b12594 жыл бұрын
I used the cable that was on the cart already.
@Addictraining0074 жыл бұрын
Thanks for your reply ! The thing that I dont understand in your set up how can u down shift if you have only one string to pull ? (To shift gear)
@mr.b12594 жыл бұрын
It is a solid wire cable inside a sleeve that allows it to be pushed or pulled. It's not like a bike brake cable.
@Addictraining0074 жыл бұрын
Thanks for your help
@nate321855 жыл бұрын
Cool build. What gear ratio you running. I know you said it wasn’t running right but It sounds like the gear ratio is too high as well. Are the jackshaft sprockets the same? Kinda looks like the sprocket on the engine side of the jackshaft is bigger.
@mr.b12595 жыл бұрын
Thanks! The sprocket from the motor is a 16 and the one to the axle is a 12. After getting it running good, the gearing seems just right.
@devilsownreject43234 жыл бұрын
@@mr.b1259 what was the final axle sprocket size
@mr.b12594 жыл бұрын
@@devilsownreject4323 I'm not sure. It is the stock rear sprocket that came on the kart.
@pargaulansidjabat40775 жыл бұрын
How much is this Mr?
@commantrosexetlos47005 жыл бұрын
all the builds i saw they made the easy difficult...no one even thought keeping the bike engine in her own frame? just cut the front and the back of the bike and meld her in the back of the buggy...that way there is no relocation..all the engine mounts with the anti vibration rubbers..and with the 19l tank ready on...THATS IT...a friend call me to say my opinion on his project because i have a lazy mind that makes all more simple..he done like i said and he saved a shit loads of money..its sooo painful to watch going into chaos wiring fucked up for WHAT? with the way i said above you need only 500euro of melding and 3-4 parts just for clutch-gear shift-axle..but no reverse
@bcjdwbiernfjherwfbowfib5 жыл бұрын
Where did you get the engine? And is that a kandi go kart?
@mr.b12595 жыл бұрын
Yes it's a kandi kart. I tore apart an old yamaha motorcycle to get the motor.
@tonyruiz43085 жыл бұрын
Wow thats a big engine
@mr.b12595 жыл бұрын
Definitely don't want to push the kart to the limits of the motor!
@adamcarpender67215 жыл бұрын
Kind of makes no sense to put that big of a motor on it when you go out of control in first gear but that's my opinion still pretty cool
@aaronkhenkin78523 жыл бұрын
Hey man anyway I can get in touch with about this build? Im about to do my own and I have some questions
@mr.b12593 жыл бұрын
I'll try to answer what I can. Email me somethingrandom906@hotmail.com
@jdsstegman5 жыл бұрын
Kick stand safety switch is more likely your cause.
@gsrhatch144 жыл бұрын
Looking in to building something similar. How hard was it? Any pointers?
@mr.b12594 жыл бұрын
Just have fun I guess. If I do this again, I would use a fuel injected motor for sure.
@FedupwitDC4 жыл бұрын
Is this a Tomberlin frame?
@mr.b12594 жыл бұрын
The brand of the original kart is called Kandi
@teukuchanel89315 жыл бұрын
Beli dimana bang
@dylanbaldwin79345 жыл бұрын
My dads gonna get a motorbike engine and we ar gonna put on a frame kinda like yours and then we will go from their. Im 14 and i cant wait to rip it on tye dirt roads at my house and take it to the mountains and hills and stuff. How cabable is yours? How fast?
@mr.b12595 жыл бұрын
This thing will probably do about 80mph. Haven't tried too much off road or climbing. It's a blast on dirt roads and spinning circles in fields.
@dylanbaldwin79345 жыл бұрын
Cool man thanks for the reply. Im not sure what kind of engine i am getting for mine but hopefully 450 or over. I love getting the adrenaline from hauling it. And also can u update me when u try some hill climbing please. Thankyou so much.
@scottoconnell53095 жыл бұрын
I traded a dirtbike for a gocart / dunebuggy and when I got it the engine wasnt attached to anything and I want to know if it runs but idk how to test it off of everything
@mr.b12595 жыл бұрын
There's way too many things to try to go over in a KZbin comment. I'd say find somebody local that knows a little about the motor you have and go from there.
@mr.b12595 жыл бұрын
But if you do get it up and going, make a video and share it!
@danhammond84065 жыл бұрын
Most of these chinese karts use a gy6 engine. There's tons online now about them
@HOOLIGANUTV3 жыл бұрын
Kickstand switch!!!!!!!! That’s why it cuts out when you put it in gear
@erickmaldonado91775 жыл бұрын
Do you have any social media that I can contact you for info? I'm doing a Yamaha 600cc swap on my hammerhead 150cc dune buggy. Do you have the links for the parts used on the dune buggy?
@mr.b12595 жыл бұрын
Well I'm pretty anti social on social media, I don't use it very much. As far as parts, I mostly made what I needed or used what I had laying around.
@mr.b12595 жыл бұрын
I'd love to see a video here of your build!
@erickmaldonado91775 жыл бұрын
@@mr.b1259 I still have the stock engine in the dune buggy. I was thinking to do the swap once the stock engine failed on me. I'm not sure if I should go with a 600cc or 750cc or a 1000cc. I have someone that wants to trade there complete motorcycle. He has two to choose a 750 Honda cb and the other is a Yamaha r6 and they both run. I also found a Yamaha fz1 1000cc engine with everything I need like harness, speedometer, engine, carbs, throttle cable, clutch cable. He wants $300 for that engine but the problem is that idk if it starts because he already has the engine pulled out from the bike and in the pictures it looks like it's laying in a stand.
@mr.b12595 жыл бұрын
I'd say take a complete running bike and start from there. It's nice to have all those parts in case you want to use anything else from it. So either of those bikes would work well. If one is fuel injected, I'd pick that one.
@georgemichael69225 жыл бұрын
That thing has know power for a 600cc bike engine and it ticking so loud because there's a lot of friction from the gas in the engine
@mr.b12595 жыл бұрын
Yes, it had little power at the time of this video from the carbs not being adjusted right. Since then, I got the carbs set right and it runs amazing and has plenty power. As far as the "ticking"... I'm not sure what you are talking about. The motor is pretty solid.
@FamilyChannelfun325 жыл бұрын
I want it ! Ha
@OmarRodriguez-xu3lz5 жыл бұрын
Hey man do you still have you buggy
@mr.b12595 жыл бұрын
I ended up selling it.
@tonyruiz43085 жыл бұрын
Be sure u got a kill switch u dont wnt that puppy sticking lol
@Projectred933 жыл бұрын
Are you in NoDak? I know no one around here that builds these kinds of things.
@mr.b12593 жыл бұрын
Where you from?
@Projectred933 жыл бұрын
@@mr.b1259 Northeast North Dakota
@mr.b12593 жыл бұрын
Now you know 1. SW ND
@shanethomas63683 жыл бұрын
What is it
@commantrosexetlos47004 жыл бұрын
why 2 chains in the back?
@mr.b12594 жыл бұрын
I wasn't able to go straight down from the motor to the axle. Check out the other videos of the build.
@commantrosexetlos47004 жыл бұрын
@@mr.b1259 oh ok thanks mate
@jaoutdoors72785 жыл бұрын
What’s the top speed
@mr.b12595 жыл бұрын
I haven't taken it there. I've been to 60mph, I'd say it would do at least 80.
@driveitbreakitfixit74965 жыл бұрын
Were did you get that engine from
@mr.b12595 жыл бұрын
I bought an old motorcycle from a friend
@awsomesauce035 жыл бұрын
From a 1998 sazuki Grand Vitara
@mr.b12595 жыл бұрын
No, a 1984ish Yamaha Radian.
@awsomesauce035 жыл бұрын
@@mr.b1259 are you sure it is not a 1.4 1998 sazuki Grand Vitara
@mr.b12595 жыл бұрын
Yes. Check out the videos of the rest of the build on my page.
@davidmorgan86123 жыл бұрын
You need to change the sprocket size because you are not in the power band.
@mr.b12593 жыл бұрын
I geared it down at the jackshaft because i didn't want this thing to do 120 mph.
@rodolfoermocilla46322 жыл бұрын
Mortal
@uwanti72015 жыл бұрын
Nice, i did the same. Check it out if you wil 👍
@ufoxfox43524 жыл бұрын
It coil is earthing of something cauaseing it to not rev up right ur not even getting half that engines power trust me, and your air &fuel mixture is wrong ,,otherwise shes a success mate ,👍
@FamilyChannelfun325 жыл бұрын
Doesn't sound right
@kimjones12703 жыл бұрын
That engine revs to like 11k your barely using the first 3 so seems seriously slow
@mr.b12593 жыл бұрын
I tried a top speed run and hit 70 without 6th gear. That is WAY faster than that kart should ever go.