Fire Alarm System GENT Vigilon by HONEYWELL

BASIC PROGRAMMING of SECTOR input/output. BUILDING WISE ACTION

[@oryxfire673]

I sure will follow you

[@royalgaming9831]

Hello sir if i want use this software which course i have to do programable logic controller?

[@florendoregner]

You need to contact local distributor to assist you. If you need hep to locate local distributor or you contact me at regner220@gmail. com

[@maa_a7244]

i want to know how to clear high resistance fault in gent vigilon

[@MdKalim708]

Can you make a complete video on programming

[@ammaraloush6313]

This winmag ?

[@MdKalim708]

Can you make a video on gent panel networking and its programming

[@florendoregner]

You need to contact local distributor to assist you. If you need hep to locate local distributor or you contact me at regner220@gmail. com

[@mohammed-cz9hz]

Good doing brother Please how I can solve high resistance fault in gent

[@syedsulaiman2262]

How to program in gent vigilon "Example: Four panels are network-connected, with one panel working as the master panel. For instance, if an alarm is activated in any building, all activities need to be reported. Then two buildings are connected, and a device is activated in one building, it should trigger simultaneous evacuation in both buildings. Then however one building is a separate entity

[@forkan_mohammed2708]

Thanks 👍

[@florendoregner]

Welcome

[@MOHAMMADJAVED-jb4pk]

From I can have software?

[@CookWithAkhter]

When i test one floor everything is working normal elevator stopped, AHU stopped,Access door open. In other floor elevator continuously working and other things working good. What will have to do please reply. Is it programming issu . Can i solve from winmag plus please give me reply

[@florendoregner]

check your program if what is the proper actions when you triggered the device in one floor, and if you want to be general actions so you need to assign the device to all output signal action during the event of fire . and you can do manually in the panel if you know it how to re-program or can you do it in gent com.tool software. There is no option to do it in winmag pc.

[@CookWithAkhter]

@@florendoregner can you tell me how to do from panel

[@CookWithAkhter]

I need your help. Please give me your e-mail id

[@florendoregner]

@@CookWithAkhter [e-mail]

[@CookWithAkhter]

Dear sir I hope you are doing well I am jawed akhter Fire Alarm Technician I need your help related to manual programming from panel We have gent vigilon 6 loop card panel We are using one loop card for one floor When we pressed the MCP OR any alarm cases some activity is going on. Sach as stair fan running. Elevator stopped, AHU stopped, Access door open for every one we are using s4-34420 interface module. When alarm coming in 3rd floor every thing is working good. For example AHU stopped, Stair fan running, Elevator stopped, Access door open every thing is working fine But when we pressed MCP in 2nd floor Elevator not stopped, and stair fan not runing . Please tell me how to program manually from panel

[@karthikeyan.s7502]

Hi Boss, how do the floor wise programming for civil defense, ex. 4 loop Facp, 10 floor building.can you explain me.

[@kumalamandol2878]

Shar your componey hab vecation or not??

[@mohdarshil3212]

Can you provide me gent panel programming software

[@djboy8886]

Hi would be aboe to provide me with the software? Love your videos and thank you

[@sukualon]

@@florendoregner hai. Please help me I need this panel software

[@florendoregner]

@@sukualon contact me

[@محمود-ظ3ت]

@@florendoregner ه

[@florendoregner]

Contact your local supplier for support to obtain factory training in order you can get on it. For further explanation you can contact me at : regner220gmail.com

[@MuhammadUsman-th5pq]

Very helpful sir . Can we edit location by using panel keyboard. Thanks

[@florendoregner]

Yes

[@Dime_Bar]

@@florendoregner maybe

[@giantgobblin1026]

Yes you can...

[@Dime_Bar]

No

[@junreyintes6523]

Sir I need the software thank you for kind sir

[@DW-ei1zr]

Bro how to find this software

[@florendoregner]

Contact your local supplier for support to obtain factory training in order you can get on it. For further explanation you can contact me at : regner220gmail.com

[@giantgobblin1026]

Who can answer...How to configure monitor module as fire using panel without comtools?

[@florendoregner]

Not possible.Output module single interface you can program without software, but monitor LV module is not possible. Contact me for further explanation: [e-mail]

[@swmltrainspotting]

I need this software

[@florendoregner]

You need to contact local distributor to assist you. If you need hep to locate local distributor or you contact me at regner220@gmail. com

[@achu3007]

Can i get gent software??

[@achu3007]

Ok

[@MOHAMMADJAVED-jb4pk]

Hi Renger, how you can help me in panel programming

[@arinzechristopher2349]

Thanks, pls how can I get the software?

[@InFlowAnswer]

I want this software bro

[@florendoregner]

You need to contact local distributor to assist you. If you need hep to locate local distributor or you contact me at regner220@gmail. com

[@rukurukin4359]

saan po kita pedeng iadd sir.

[@syedsulaiman2262]

Please make video How to program and purpose Master group Master sector link Delay block Delay block link Time slot Command builds Message routing

[@MOHAMMADJAVED-jb4pk]

Does it need dongle key to program?

[@florendoregner]

it is required license site key.

[@alumar5723]

@@florendoregner Can you help me to program the panel

[@florendoregner]

​@@alumar5723contact me at [e-mail]

[@imirzaumair]

I need software

[@muhammadasadimam756]

Can you please share vedio of how State of device can be cahnged in software

[@florendoregner]

Hi,you can change the device state condition at panel itself and its very easy to do for you. But you can used software thru device config and just put the device states option on (states) and off (states) after proceed to timeblock put designated time required by your client at site if when it be the action of youe states condition to action.

[@achu3007]

Boss u have software??

[@muhammadasadimam756]

@@florendoregner But i just want to decrease sensitivity of some devices , not want to put them off.

[@florendoregner]

@@muhammadasadimam756 yes you can do by changing state only in the panel and please refer to state condition code

[@jhazpervillanueva324]

Sir san ka nag wowork pano mag apply jan same field and gents also I handle

[@florendoregner]

work at private company.

[@karthikeyan.s7502]

what is tha password of gent panel, if normal password changed by somebody,how to break?, we have 4 sites,

[@florendoregner]

required daily password from your OEM manufacturer GENT only once you dont know the password.

[@manikandan5980]

Bro can you tell me how to do network configuration like we have 12 panel in one site. we need centralised panel to monitor. Give me some idea how we can do.

[@giantgobblin1026]

you need to add one terminal node and network card on its panel

[@DW-ei1zr]

Hy

[@gameforfun5539]

sir can i take the software from you. reply asap thanks

[@florendoregner]

Contact your local supplier for support to obtain factory training in order you can get on it. For further explanation you can contact me at : regner220gmail.com

[@niyasmohamed3980]

Good helpful haroon bhai

[@florendoregner]

It's my pleasure

[@ahmedtasin7183]

Hlw sir i need the configuration software

[@Traditional_Foods_Across_World]

whrer can i download this software brother

[@osmanmassad8104]

hi good morning it this software work with all gent fire alarm panel and how I will download it. can you please help me

[@florendoregner]

Contact your local supplier for support to obtain factory training in order you can get on it. For further explanation you can contact me at : regner220gmail.com

[@waqas7783]

hi boss I think you r doing great great can you please reply me with the Gent configuration software ?waiting for your urgent reply.

[@florendoregner]

thank you and contact me [e-mail]

[@MdKalim708]

Hii.. can you make a more video of commisioning in details

[@florendoregner]

What programming C/A do you need?

[@mohamedfarhan1481]

Good job and Useful information brother

[@florendoregner]

Welcome

[@joyaljoseph683]

Hi boss

[@joyaljoseph683]

I am working gent in Kuwait

[@florendoregner]

@@joyaljoseph683pretty much good working with gent

[@sulemansafeer7856]

@@joyaljoseph683 hi i'm also Gent Commissioner in Pakistan

[@arifhussainansari8175]

Thank you so much sir for information

[@florendoregner]

sounds good to hear feedback from you

[@arifhussainansari8175]

Yed i heared you wel

[@arifhussainansari8175]

Sir can we crak the password if posible so how to crak pls explane

[@arifhussainansari8175]

Sir can you uplode video full basic training of gent vigilon compact step by step

[@florendoregner]

@@arifhussainansari8175 no,unless you know the existing password and you can change it. or else if you dont know it and the option is a daily password log in.