Bro…..you don’t need to drill. Drop the wire down, run underneath and come up through the floor grommet tht holds the emergency brake cable. There’s a spot in the pass side as well in the same spot but requires a step bit and is the BEST spot I’ve EVER seen for a pass through.
@abedj12202 жыл бұрын
Thanks for this Tip. going to look for this in my 2012 suburban
@trebalong39486 ай бұрын
thank you!! clutched up
@TysonMooreBuilds3 жыл бұрын
This was very helpful. I would have never known where to drill without your help. Thank you!
@stephenjones43103 жыл бұрын
Wow! I've been looking all over the web for months for what you just showed me. Thanks so much!
@JonsGarage89 Жыл бұрын
That dimple and hole is where the clutch pedal and master cylinder go through the firewall on the mexican market trucks.
@Willy721210 ай бұрын
Thank you. Great video. I have been looking for a place to run 2 small wires through firewall on my 2012 Yukon. Most videos say to cut the boot in main wire harness. That is just asking for problems. My 2012 Yukon had exactly the same dimple and hole on the inside. It is much easier to drill carefully from inside of the truck. Cheers.
@jakeruiz50623 жыл бұрын
Thank you so much I was sratching my head. For half a day. As my uncle had his stereo done and took up all the usual spots I would normally use. Much help also doing a dual battery setup for him . Looking forward to your video. Thanks a lot. Truly... major help.
@jeremyfrancis8207 Жыл бұрын
Awesome. You're video was only one that was helpful. Thanks 👍
@110americalovingpatriot24 ай бұрын
Thank you for the help.
@Highway5543 жыл бұрын
Thanks that’s was exactly what I needed to to run extra horn cable. That was very helpful.
@cpreovol3 жыл бұрын
On my dad’s 09 Silverado, that dimple and the hole in the plastic on the inside of the cab did not line up, they were about an inch off. No big deal though, just has to drill all the way through the plastic from the engine bay side. Thanks for the help, everyone else says to punch a hole through that big boot and run the wires through and that seems like a pretty slapdash way to do it.
@rogerkk4znuraywwf3963 жыл бұрын
I've been trying all day. Thank you for the tip.
@HeirloomReviews2 жыл бұрын
Hello this was a very helpful video! 💪 Live your channel!! 💖 Thanks for sharing my friend!!!💯👍👍👍👆🌹🌺🌻🌼🌷211
@daviddavis36192 жыл бұрын
Super helpful. Awesome video thanks so much
@jassem33334 жыл бұрын
Thank you i have 2008 yukon and i think thats what im looking for good job 👍👍👍👍
@glenfrancois68133 жыл бұрын
Why couldn't you go through the black plastic piece that you took off to pull the installation back
@alvarezbenjamin85194 жыл бұрын
Thank you, was lost where to drill a hole safely.....
@Guyontables4 жыл бұрын
On my 2013 silverado, the larger outward area inside the engine compartment does not align with the square indent inside the cab if anyone is making that comparison. That square area is even where the engine head meets the block at the rear of the engine about 4" to 6" lower and to the left.
@kmann0027 Жыл бұрын
Sweet and simple, thanks mate
@woodandtable Жыл бұрын
Thanks! About to do an install on a 2013.
@elbatobeach8 ай бұрын
does a Drill fit to drill the dimple?
@campman8670 Жыл бұрын
thank you for this I have a cb in my 2009 gmc sierra and don't want to use my cigarette lighter outlet to power it as that is not the correct way to power it as well powering an Amp
@TravisBurrell3 жыл бұрын
Thank you very much for this!
@hydrorock94692 жыл бұрын
I would enjoy a video on your dual battery cb setup. I’m currently doing the same.
@elbatobeach8 ай бұрын
I run all my accessary wires/cables to a secondary battery to a main power block if Need more attachments
@markwilliams23542 жыл бұрын
Did you get any answers on the 5.4 triton noise? Mine is doing the same thing.
@ArmenArmenjs3 жыл бұрын
How about 2004 GM trucks are there any pre holes?
@cpreovol3 жыл бұрын
Ps a right angle drill really is helpful here
@alpha_arlin2 жыл бұрын
very helpful
@rougarouarms2 жыл бұрын
Hey friend. You commented on one of my videos, unfortunately youtube deleted the comment. Wasn't able to read it.
@Corey2base2 жыл бұрын
I found the hole and it would be a perfect place, but how am I supposed to fit a drill either under the dash or in the engine bay… like… am I just dumb? It’s impossible to fit anything larger then like 4 inchs into the space on either side
@abedj12202 жыл бұрын
Same question. maybe remove the fuse box under the hood?
@atticusmccoy67014 жыл бұрын
Hey man what was the whining noise on your f150?
@someonesmail96115 жыл бұрын
شكرا 👍🌹🌹🌹🌹🌹
@khadijacharik28564 жыл бұрын
السلام أخاي. الله يخليك عندي إجازة هذا السنة وبغيت نقرى ماستر في كندا. واش نقلب على محامي مختص في الهجرة أو نصيفط بوحدي واش عندك فكرة شحال ديال الفلوس خاصني. وشكرا بزاف وفقك الله
@قناةالمجلةالإلكترونية2 жыл бұрын
خويا خالد فين غبرتي اخويا رجع لليوتوب توحشناك
@worldtv19585 жыл бұрын
Slm khoya cv 3lik khoya ila kanet 3andi dar dyali nakhod viza siyahiya L usa ola Canada tantkhales 3700DH nakhodha Allah i7afdak
@mrkamal.officiel4 жыл бұрын
What you have done is amazing , can we contact you ?
@omegalupus93534 жыл бұрын
salam alykom akhi khalid brit email dialek brit nastacher m3ak f hijra chokran bezaf