Fix parkside pala 20 A1

Fix parkside pala 20Li A1

[@nandorszelei6944]

Nagyon örülök e nagyszerü video megtekintésének. Most van folyamatban egy hasonló ágmetsző készitése Igy nem bonyolult a szerkezet elkészitése. Aggodtam hogy motorikusan egy csavarbehajto motor hogy fog megfelelni e célra. A látott video megnyugtatott igy elkészitem, s majd beszámolok róla. Köszönöm szepen , nagyon sokat segitett . Nandor

[@zana3587]

köszönöm, Uram. remélem hasznos lesz az Ön számára

[@Mustafa.B2]

Wonderful job, brother. We miss your wonderful videos.

[@zana3587]

thank you my teacher, i try make more video in futur, my best friend

[@user-od2sb9ez3c]

Спасибо за интересный обзор!! Интересный секатор!! Хороший ремонт-молодец!! С заточкой режущих кромок надо ещё поработать. Немного жуёт рез-не критично, но заточка слабовата! Я тросики всегда с кислотой паяю-особенно наконечники. Часто велосипедные тросики приходится паять.

[@zana3587]

спасибо сэр за вашу информацию

[@valmonta3647]

Welcome back, great repair again

[@zana3587]

thank you sir

[@Velo_Tver69]

Hello my friend, as always, work is at its best! I didn’t know that Pakrside has such a large range of battery technology. But unfortunately we don't have it in our country.

[@zana3587]

thank you sir, i bought both of them in old market

[@stalkers6929]

Brawo. Fajny materiał.

[@ganpatsolanki567]

Good job...KING OF PARKSIDE 👍🏻👍🏻👍🏻🤴

[@zana3587]

Hhhh . Thank you sir

[@zakmburg3581]

You make things simple, wel ldone man سلام

[@zana3587]

Thank you sir

[@ahmedahmed-fz6vo]

الله يوفققك ويبارك فيك وفي اولادك

[@zana3587]

اشكرك اخى العزيز

[@Amperekaefer]

Guter Job👍👍!!

[@zana3587]

Danke mein Herr

[@kurdish429]

جوانه جوانه ده ستت خوش

[@zana3587]

سوپاس . بەرێزی

[@AntonioOliveira-xj5om]

Welcome! Thank you!

[@zana3587]

thank you sir

[@ivanakoide9090]

4:00 Did you use tin/lead alloy for soldering? Tin/lead is pretty soft alloy, there is no wetting between tin/lead alloy and steel wire. Only friction forces remain, and pulling forces are quite strong. How long such joint will last?

[@ErCanEverything]

👍

[@zana3587]

Thank you sir

[@itxasoarmendariz971]

Hola,el problema de la avería es por el engrase??no es lógico que tengas que soltar todo el cabezal para engrasar no??puede ser un fallo en su fabricación???, saludos de Jose desde spain

[@zana3587]

Gracias, es un defecto de fábrica.

[@akshaygorai7945]

Thanx sir, plse load wood router armeture winding video

[@zana3587]

thank you sir ,ok i try

[@akshaygorai7945]

@@zana3587 sir I'm rewind many bosch600 angle grinder armeture,there is a problem fase,all are short few days after use, all r amp.also ok and not spark, why this proble occurred

[@akshaygorai7945]

@@zana3587 sir plse. Send your email,I'm sending my armeture winding and problems

[@maithemabbas2275]

🌹🌹🌹🌹🌹

[@zana3587]

Thank you sir

[@andreabugatti6792]

Today I used the pruner but at one point when I pressed the button it made a long warning sound and didn't cut. I changed the battery, turned it off and on again, waited an hour thinking it was overheating but it doesn't work anymore. Do you have any idea what it could be?

[@Muhammad1977ma]

أحسنت أستاذي عملية صيانة جيده المادة التي لحمت بها هل هيا صولدر

[@zana3587]

اشكرك اخى العزيز . نعم صولدر

[@kahlid-ataya]

اهلا وسهلا بك نور اليوتيوب 4:20 ما نوع اللحام الذى استعملته هنا فضة ؟

[@zana3587]

اشكرك اخى العزيز ز استعملت الصولدر الذى يستعمل فى لحيم القطع الاليكترونية

[@kahlid-ataya]

@@zana3587 شكرا للتوضيح

[@user-sp8yi6ws2m]

فيديو جميل ...هاذي القناة غربية لو ايش لان انتاج الفيديو جيد لكن بدون تعليق من المقدم ...ممكن الاجابة

[@zana3587]

اشكرك اخى العزيز

[@rextransformation7418]

(5:55 onward) when it doubt, slap on lots of lube. 🤭👍

[@goranjevic9975]

x

[@zana3587]

y

[@pawelw.9172]

you load toooo muuuch grease...

[@zana3587]

no sir

[@pawelw.9172]

@@zana3587 too much indeed...

[@zana3587]

it must be like this

[@pawelw.9172]

@@zana3587 most of it will end up outside the gear housing anyway.. too much, 1/3 of the gear box max, you fill until full.. the motor is gonna force through resistance created by too much lubricant... your choice.. let me show you the amount of grease in the new milwaukee ag9-125 grinder: photos.app.goo.gl/UpVmTQhdd6X7S6j58 you see - this is the correct amount and no more, you put too much grease... it will make the tool work hot.

[@pierostefanelli1408]

L

[@zana3587]

!