Fixing & Avoiding Warped Die Cutting Plates

[@laurabuehler]

I created my own shim to use only if I'm not getting a good cut. I ran a laminating pouch through my laminator and created a clear plastic sheet. You can them trim it down to fit into your machine. It's not super thick like metal and it still has some "give" to it. It doesn't flatten over time the way a cardstock shim does so it can be used over and over again. If someone needs a slightly thicker shim they can laminate a piece of cardstock to have the thickness of the cardstock added to the thickness of the laminated pouch.

[@gailies2223]

Thank you Laura, I will give that a go 💜

[@mrspickle8285]

what a good idea. Might give this a go, thanks for sharing.

[@robinrichards3003]

Thank you so much for the laminating tip. Will try it.

[@sarahh5988]

So clever!

[@pattylovescrafting5544]

Love this tip. I got a laminated piece as packing material and use it but it is getting warn so this is a great option. I was thinking of using a sheet of acetate from packaging but this seems more durable. Thanks.

[@ninasocal8181]

Just jumped up after watching this....startled my husband....boiled water,waited the 20 minutes....and...WHOO HOO! I have an old Cuttlebug machine so these plates have been around a long time. THANK YOU SO MUCH for sharing!

[@soupdragon3377]

He didnt think you were about to give birth then!

[@susanknight183]

Thank you Jennifer for all the research, you are going to help so many people save money with this advice.

[@sarahh5988]

I use an old cuttlebug too!

[@905lovest]

How FANTASTIC for those with Cuttlebug machines, as the plates are no longer made. WONDERFUL!!!

[@melodieisreal5933]

Thank you for taking the time to do this and thank your husband for his comments!

[@EnvisionThisNow]

I have a Gemini and used your technique to flatten my plates and it worked like a dream. I did one thing different though. I didn't remove them after 20 min or so, I actually waited till the water cooled right down. My plates came out perfectly flat. One plates had one die cut mark in it and you can't even tell anymore, its gone! , talk about a WOW moment. The other plate's marks decreased significantly but can still see some remnants of die cuts in it. But all in all, I couldn't be happier for them now being the next best thing to new :) Tyvm for sharing this with us!! ... and I thank your hubby too!

[@lindakf27]

Jennifer, "thank you" doesn't seem like enough, not just for your wonderful videos through the years, but for this one especially because it is geared for everyone who uses a die-cutting machine. If there was a Hall of Fame for crafters like you who produce such highly informative and professional videos consistently, you would surely be nominated every year in the category of "Best 'Sharing' Crafter through Video Excellence".

[@jenniferbandy1697]

and instead of a statue, she should get a crown!

[@cfluto]

Thank you, Ken, for mentioning the dangerous vapors that are released in the oven.

[@CanadianQueenmagenta]

I was so pleased Ken mentioned this as well Carol. I have seen a number of videos on flattening plates by putting them in a very hot oven and I have known for some time that when you heat plastic toxins can be released. I would not insult the provider of those videos but it's very concerning when being told to do something dangerous.

[@cindiyoungstead9159]

I love how you and Ken work together. (Nerds of a feather work well together!) We can’t thank you enough for all you’ve done and continue to do for our wonderful crafty community!

[@jennifermcguireink]

Our pleasure!

[@4551mac]

I am so glad you showed the double sided Gemini plates. I purchased a set when they came out over a year ago, and kept asking on tons of videos if they could be used on single dies. No one ever responded that I can recall... I even questioned on the Facebook Crafters Companion posts... A few months ago i broke down and started using one, and to my absolute amazement and shock, it has NEVER warped and has cut great. I think they will be my only future purchase on plates. I have the warped clear plates, and plan on using your boiling water method to try and straighten them out. Taping my plates did not work for me. I love my Gemini Jr... and with you sharing this tip others will not be afraid of using the double sided plates for regular dies. I guess I was afraid my dies would somehow warp themselves using these fantastic plates and be ruined. Thank you so much for helping us crafters out who may not have the resources you have... sharing your info has been a life saver for many of us ! Thanks to Ken too... His explanation makes perfect sense ! Happy Crafting !! Stay safe...

[@JenniferCountryTwinkle]

Tried this method last night. All I can say is THANK YOU Jennifer! Worked like a charm!

[@colbycheeze8924]

I LOVE this information from your husband. I really appreciate it and no, I don't think he's a nerd; he's an engineer. Makes so much more sense to receive a scientific reason for this. Thank you

[@ArtemisToo]

You are a godsend to the papercrafting community, which this video demonstrates so well, and I just want you to know how much we cherish you!

[@jennifermcguireink]

You are so very sweet. Thank you

[@kathymcconnell6852]

Jennifer, you may not describe yourself as an expert but you are the first person I turn to when I have a question about anything cardmaking-related! Thank you for this excellent tutorial! ❤️

[@s_rofbear]

“Ken is a chemical engineer, and he’s going to use words none of us can understand…” I can’t tell you how excited that sentence made me! 😂 My little nerdy heart was like, “Ooooo! New words! Learning! Knowledge! Yay!” Edited to add: Ken’s explanation was wonderful! There were new phrases for sure (I can’t say “glass transition temperature” has been an everyday phrase for me 😅) but the explanation was still perfectly understandable! My little nerd heart thanks you for including the science behind the method! I enjoyed it just as much as I enjoyed watching wonky plates become straight ones again. 😁

[@jennifermcguireink]

Love nerds!

[@bookwormbon482]

I feel the same @Sarah P!

[@jenniferbandy1697]

I'm married to a brilliant chemical engineer and my daughter just finished her second year of chemical engineering study at Colorado School of Mines. When they get together, it sounds to me like they are speaking in a foreign language! Love my nerds so much!!

[@JanetSkerry]

Thanks for taking the time to show us this technique. And, thanks to your husband for explaining the why.

[@facsmom]

Thank you so much for the research, testing, and sharing:). I am a retired home ec teacher who LOVED the marriage of science and life (food, nutrition, fabric, clothing, household materials . . . ). Whenever I think of Ken I think of Press-n-Seal traveling from kitchen to craft room♥️

[@ienjoygardening7361]

OMG I choked on my drink. I am married to a chemical engineer too and they talk in a different language. Great tips though that I hope to explore to save some money on plates so I can spend more money on the fun stuff!!

[@annettehogan8797]

I have spent all day cleaning and organising my craft room. I am now going to take my warped plates back out of the bin to try this process so thank you so much 😊

[@denisebrennan2083]

OMG you are a genius, I bought my Gemini a few months ago, but it was driving me mad as my plate were warping and my card stock was just a mess, this option is incredible, I am sitting using my machine and positively purring at how nice my die cuts are now.... Genius... thank you

[@ritamariacastillo8812]

Thanks for sharing, Jennifer. I´ve been doing the hot water procedure for more than a year, except that I leave the plates in soapy water to loosen the paper fibers trapped in them, since hot water expands the material it´s easier to brush off the residue. It works for me.

[@jennifermcguireink]

Sounds great!

[@CMeyer-vl3op]

Thank you for sharing this. Unfortunately, my plate was SO warped that the boiling water didn't work! I decided to put it in my toster oven. Since boiling water is 212 degrees, I figured that close to that was worth a try. 225 didn't work, but 250 worked like a charm!

[@lisaloiselle4562]

I wish I had known about this years ago. I have gone through so many big shot plates. THANK YOU! And nerds make the world go round.

[@charlirobinson1548]

Get a Magic Mat and your top plate for your Big Shot shouldn't warp ... at all! I got the Magic Mat and absolutely no warping from my Big Kick. I LOVE it. But my Gemini warped it! So I won't ever use my MM in the Gemini again.

[@kkrolf2782]

We may not make the world go round, but we keep the gears oiled, and the thing tuned up!! 🧐🤪🤭

[@hisdaughterdeb7316]

Okay, so this is 3 years old but the timing could not have been any more perfect! I just followed your suggestions today with my Gemini 9 x 12 badly warped plates and WOW!! WOW is actually an understatement! Thank you so, so much. This is a total game-changer!

[@mmmmlllljohn]

Who knew our plastic plates had glass in them and that stain glass windows could flow …! So interesting, thanks, Ken! And thank you, Jennifer, for being so tenacious in finding solutions for us crafters! ❤️🇨🇦

[@vidbox44]

Die cutting plates and machines are the biggest conundrum of my crafting journey. Thank you so much for tackling the science of these problems!

[@charsbabushka]

PS The glass info from Ken was really amazing. I did not know that glass would continue to flow. What a great piece of knowledge.

[@jensesanify]

We used to live in a VERY old house and it was always fun to show visitors how the bottom of the glass in our window was thicker than the top! We never did replace those windows because they were well made (and a fun conversation piece).

[@chrisarlington1792]

I keep reviewing this video. It is so comprehensive. It took me years to find these tips out. Bless you

[@jennifermcguireink]

Hello! A few added things: - The double sided plates will be back in stock soon! *** UPDATE: The green double sided plates have not warped at all. It does wear after ton of of die cutting (1000+ passes), but I just used the other side and continued. So - as with any cutting plates - they will have to be replaced at some point but not due to warping. *** REMINDER: Cutting plates are meant to be replaced eventually. Eventually all plates will wear too much, break, etc. But I find these tricks help to make them easier to work with for the life of the plates! (aka no warping) - Someone asked if the double sided gemini plates will dull your dies. i have not noticed that happening, and i have mass-produced-die-cut with them. and i would assume they wouldn't dull them as those plates were designed for it. That is my guess! - I have not tried these double-sided plates with other machines. - I do not think flattening plates will effect the life of a plate. But it is hard to say and be sure. Plates are expected to have a limited life span and be replaced at some point anyway. I am just trying to find a way to make them useable for a longer time :) - To see the correct way to use the double sided plates with double sided dies, check out this video: kzbin.info/www/bejne/a6mtlZhui5eajqM

[@patwoessner198]

Will those double sided plates work on the big shot? I ended up with one of the cute double sided dies as a gift....but only have a big shot..thanks for all the great ideas!

[@Kim-ql1kj]

Will the taped sandwich plates work in the empress?

[@jennifermcguireink]

I normally don't tape the empress, and use empress plates with it only. And I don't have problems with them warping. 🤷‍♀️

[@sassypowers]

Well what’s interesting is that these plates are made for double sides die cuts but warp less because they are made stronger than the regular plates. Im all for reducing the layers that is needed t get the same outcome, especially when it is less work for maintenance. 😌 Its the gemini thats new to me, not purchasing new cutting plates. Ive had mega dozens of those.

[@suethornton5]

I tried the boiling water thing with one of my green plates because I thought it would get rid of so much white stuff embedded in the plate. It was not warped. I thought it was paper. It did not get rid of the white stuff and very little paper stuff came out. BUT I have a feeling that procedure was not good for those particular plates because now the plate is chipping chunks of plastic off on the one side that is always against the cutting side of the die. It's almost like a layer is coming off. I have only had the plates since Sept. 7th and have not done nearly the cutting that you undoubtedly do, Jennifer. So I ordered a new set. For now I turned the plate over and will use it that way until it needs replacing. Then I will move the other plate I'm using now to the side that's getting all the cutting and put one of the brand new ones in it's place. (Clear as mud?) Anyway. I so love not having to add shims or mats or metal sheets, etc. Just the two clear and two green. I did not tape mine as it was really no problem. Would it be better to tape them, though?

[@CanadianQueenmagenta]

Thank you Jennifer and thank you Ken for sharing the dangers of putting plastic in a hot oven. Much appreciated.

[@jennifermcguireink]

You are so welcome!

[@jacquipaper]

Thank you Jenifer for confirming what I have been doing for years. We need your videos and benefit from them greatly. Bless Ken, he is a super wonderful chap. I too am from an engineering family and we see things differently to other people, it is a blessing and it has taken years to be happy being a square peg in a round hole type of person.

[@manongatehouse4047]

I had 2 very badly warped clear plates and a warped shim. I tried your system but gave them much less time, I could actually see them levelling out, but it still worked 😊 thank you for the idea.

[@betsygreen5048]

Thanks Jennifer! I am excited to try this when I need it next. Thanks to Ken for the explanation too. I'm not a scientist, but always appreciate understanding the "why" of things.

[@jennifermcguireink]

Glad it was helpful!

[@micheles3896]

Thank you! Great info! Ever notice how many of us crafters have nerdy households? There is definitely something to that!

[@bretonbird4812]

Love this. I have another hint. I have extended plates and large Gemini plates that will not fit under a pot fully. I use a jelly roll pan (cookie sheet with sides) and put in a small amount of boiling water and the plate. Then I put another jelly roll pan on top. Add more boiling water and then a heavy pot on top. This gives even pressure throughout so no end curls or water bubble blips to deal with.

[@jensesanify]

Great idea!

[@jragnes]

Me too. I also discovered that I can put them in my dishwasher. I don't have to boil water then! I have the large gemini also. I put all the prongs of my bottom dishwasher rack down (all of them will lay down rather than stand up. I then put a large cookie sheet, my plate(s), another cookie sheet on top and a heavy pot on top if that 2nd cookie sheet. Turn my dishwasher on and walk away. When the cycle, including the dry cycle is done and the water in the pot has cooled, I come back and dump the pot of water out and remove the cookie sheets and my plates are flat again! I figured this out bcz I was tired of getting water all over my counter when doing the cookie sheets on my counter with boiling water since my sink is a double and not big enough to accommodate the larger cookie sheets. That being said, DO NOT PUT YOUR CUTTING PLATES FREESTANDING IN THE DISHWASHER. THEY WILL CURVE UP LIKE NO OTHER. I HAD HEARD GINA K SAY SHE JUST PUTS HERS IN THE DISHWASHER AND THEY COME OUT GREAT SO THAT'S WHAT I DID. I was able to fix them by boiling water and softening them enough to get a less of a curve in them and then I did the cookie sheet thing in my dishwasher and to my surprise that's how they came out flat again. Otherwise I was going to be buying 4 new plates

[@lilysandell4638]

I have recently received a used Gemini junior machine the plates are not to bad at the minute but if I do the tip in this video, does the pot that goes on top have to have boiling water in as well? Or could I just boil the kettle then pour that in the plates and put like an empty sauce pan on top? Sorry I’m replying to. Your comment it won’t let me comment otherwise

[@crafti.louisecreates6824]

​@@lilysandell4638 the heavy pot of boiling water is for the weight of the water and the heat to keep it at temperature long enough to do the job.

[@terryfeuling5333]

Thank you! Thank you! Thank you! I just finished all my plates, they look perfect. I am so happy that I found your channel

[@nancyfinney1314]

So glad I saved all of my warped plates! I stopped using my gemini because of the warping. I should be going to bed but boiling water instead lol. You are a rock star!

[@ruthbrooks6489]

My green plates are a little smaller then my clear plates. Will this cause one to break?

[@doracruz5474]

Thank you for always being kind and positive and sharing your knowledge ❤

[@janisblevins662]

My crafting has been elevated to new heights by watching your videos. You and your videos are TOTALLY AWESOME as is your desire to share you ideas and spread the joy! My first attempt at "unwarping" was not as successful as I had hoped, but I determined the reason was that the pot of water that I set on top did not have enough weight. I had much better luck when I added more weight to that top pot. Rather than getting a bigger pot with more water (and the chance of it spilling out), I put a pizza pan on top of the pot and added an item that was very heavy. THANK YOU for this video and all the others, too!

[@papercraftingmom98]

Started the partial die cutting card and had to stop to do this to my warped cutting plate. Tidied the kitchen and did dishes while I waited. Let it cool while I ate lunch and less than hour later I was back to work in my craft room. How easy this was!

[@vickidigrado5046]

Excellent Video. And so, so good to finally "hear" the voice behind the man responsible for Press n Seal. Well done!

[@jennifermcguireink]

Thank you very much!

[@butterflygal31]

WOW! I noticed the "crud" right away! That is amazing!

[@donasimmons37]

Thank you so much! I was literally just now staring at my plates wondering how to fix the warping! All I could think was "I'll have to go buy more..." . You're awesome and I just love your videos! Thank you to Ken as well!!

[@MsShanarun]

thank you for spending so much time researching what works best!!!

[@shellyrene5708]

I’m so glad you publicized this video again / I bought the double sided plates to try the technique but for the life of me couldn’t remember the instructions or where I’d seen them. Jennifer and her nerdy family to the rescue once again. So excited to use my gemini again!! Thank you!

[@YvonneCook-gv5pq]

Wow, this is really useful! Thank you to both you & Ken for sharing! 😊

[@pattybowen3014]

Thank you so much for all the research and sharing that you do. Thank you also to Ken for sharing is knowledge! I have to admit, I loved his video where he snuck into your craft room and made a card. A nerd with a great sense of humor is a win-win!!!!!

[@jennifermcguireink]

I agree!

[@karennagata4182]

I heated water a small(5”) and medium (8”) flat-bottomed saucepan til boiling. Put plate in 9x13 heavy aluminum cake pan in the sink. Poured water from medium pot in the pan over the plate and put small pot with boiling water on the middle of the warp. (Small pot pressed on the middle bulge.) Filled a larger 10” pot with tap water and balanced it on the medium pan for weight! After about 20 min, I poured the water from the large pot into the pan so the plates would cool and harden with the weight of the small pot still on it. Poured water from the medium pot also (can scrub with a bit of detergent and a brush if needed. Good improvement in the 6 warped plates I tried.

[@rondasheive4280]

I appreciate your time on this and sharing it with us.

[@lyndaleigh121]

Thank you so, so much. Best 'warped' advice ever! Have just flattened five Gemini plates, that had been put to the back of a drawer, awaiting resurrection, and only to be used in dire emergencies. Thanks again.

[@jorogers9576]

I use the advertising cards that come in the mail. Many have a coating that adds just that little bit of thickness for a good cut. The thin kitchen cutting mats from the dollar store work well too.

[@susanlillard1635]

Thanks for this update. Since switching to a self healing mat, only the mat has warped, not the cutting plates. I have tried 3 different brands of self healing. They do straighten using a heat tool. I usually want until all three are badly warped before getting the heat tool out. Just ordered the Gemini jr. double sided cutting plates. (Plus a few items from my wish list. You can’t just order one thing, right!?!)

[@patriciamiller5228]

I have been using the double sided plates for more than a year. I have almost no warping at all with any of my plates. Win

[@lilyofthevalleysl4990]

Hi. That's great. Which machine do you have please?

[@edhood3696]

Thanks for the wonderful tips, I’ll definitely try these. I bought the double sided plates by mistake and when I realized it, it was to late to return them. I don’t own any double sided dies. They’ve been taking up space in my craft room for about a year, now they’ll come in handy.

[@robiniovino5068]

I tried this tonight and can’t thank you enough. It worked great!!! My plates look almost new!!!!!!

[@lizziedae91]

If i ever get to a sink without dirty dishes in it I will have to give this a try lol

[@SharonLuska]

Lol you’re so funny and so my kinda crafter😁🤗

[@MapleBlondieCr8s]

🤣🙌🏻🤩🙌🏻🤣

[@patriciablades448]

Jennifer in February I bought a Platinum 6 machine and within a month my plates were warped and I was beside myself on what to do. I of course ordered new plates, but they took time to arrive. So I put the old plates in the dishwasher without much success. They were cleaner, then I decided to rotate them with every cut. This was easy because Spellbinders has printing on one end of each plate. When I finished die cutting I would insert the Label end in differently each time I die cut. This helped to straighten out my plates and LOL I am still using the old plates and they work beautifully. I will try straightening out my Gemini plates with your method and I ordered the double sided plates. Thank you so much for all this information, you are the best.

[@joankamper1960]

Thank you so much for this tip. I tried it yesterday on a couple of plates that were badly warped. They are not perfect but are a ton better than before. Thank you too for the explanation of how it works and the dangers of heating the plates in the oven. As usual you did not disappoint in any way.

[@pennilane6019]

I've kept all of my old, warped cutting plates and every time when I was stashing them away my first thought was always "why r u keeping these, u won't use them again." and my next thought was always "well, u never know." My husband (the hoarder who taught me) uses the, well u never know, A LOT!! He taught me well...almost to well. Lol, thanx for this video. Love ur channel.

[@tracyjollymore6249]

Thank you so much, Jennifer! This has been an unpleasant issue for so long. I am really happy to straighten out my old plates with water :-)

[@jennifermcguireink]

Glad it was helpful!

[@hadesbobbin]

My big shot is only 5 days old and it’s my first buy, and my plates were already getting warped, because i had been experimenting a lot and trying my dies. It gave me so much anxiety to see the plates like that just a few days after investing so much money in it. But this tip is really a life saver. It worked like a charm. My plates are absolutely straight now and I am going to follow the rest of the tips too. Thank you so much Jennifer.

[@sr1625]

Trying this out today. Glad I hoarded my warped plates. I never tried putting them in the oven because I was leery of the chemicals so this is an awesome alternative 😊

[@Squabetty]

Thank you for Ken’s explanation - direct, brief, understandable!! I appreciate knowing the whys……like any good nerd! :)

[@carolhenderson5297]

Thank you for your time, effort and interest in keeping us crafters up to date on what will work best, but still giving us options. "You ROCK!"

[@verdagagnon6602]

Just this afternoon I threw out a couple of warped plates and ordered more. Came into craft room and found your post. Dug the plates out of the trash and started this video. Couldn't wait stopped video ran into kitchen and put a pot of water on to boil. Came back and watched the rest of this wonderful informative video. I also had tried the hot water method but it didn't work for me but placing the hot and heavy pot on the plate makes great sense. I can't wait to see the results. Time is up I am going to go and check. Thank you so much.

[@debbieford6862]

thank you for the tips - I also keep one of my cutting plates as a "do not cut plate" . Since I don't cut into it, it doesn't seem to warp and therefore I always have a flat surface to run through my machine. I have also purchased the self healing cut mats and have great success with those

[@kathybogner6646]

Spent all Tuesday morning unwarping my plates! You and the husband are geniuses! It works!

[@bookwormbon482]

This video has came at the perfect time!! I am literally in the process of returning my gemini because of this issue. Had my plates for only a month and it bent to the point where it won't go in the machine.

[@irenedavo3768]

Wow! That’s strange

[@MammaCass]

Same and the cutting plate has cracked across the middle. 😔

[@maryberg1081]

@@irenedavo3768 I have had the same issue. Stopped using it. Now I will try again.

[@nataliewashbrook3255]

When my large plate split I cut it in half, filed the rough edge and now have 2 smaller plates for when I'm using small dies. Saves throwing the plates away and I only use my large plate for large dies

[@debbieshealy2223]

Thank you, thank you, thank you!! I literally just went to the trash and retrieved the plate I finally had to give up on because it was starting to bend my dies. This method WORKED! It's been revived!

[@joannepitre723]

Will have to try this boiling water technique. Your husband's intake was helpful and interesting. Make sure to thank him for me.

[@anniesews]

Thanks for your method of taking the warp out of cutting plates and I will get the new plates you mentioned. Super informative video.

[@BetsyBlack0101]

Love your tips as I love love my Gemini. Thank you and thank your hubby for his explanations as well.

[@susanrossman529]

This is CRAZY!!!! I flatten three old plates (and they cleaned up nicely as part of the process) in about 5 minutes (it only took a couple of minutes per plate) and I am ecstatic with the results!!! WOW, thank you so much this is the MOST helpful advice. This will save me a ton of $'s. Thanks again. You are on my AWESOME list!

[@terrydeason1689]

Thanks so much for the tip and all the time you spent doing the research. I actually got rid of my Gemini Jr. because the warping was such an issue. I can't wait to try this out.

[@AlphaGeekgirl]

I just tried this, and although my 3-year-old plates aren’t warped (I turn them over every run through), I was amazed at how the boiling water cleaned my plates! I usually wash them every few months to remove residue from tape, but they have NEVER BEEN THIS CLEAN EVER! I can’t believe how much paper fiber and dye was embedded in the crevices. I’ll be doing this on a regular basis from now on. 😁

[@traciepond9105]

Thank you. It is always fun hearing the “geeky” explanation. My Husband is a nerd too and has a chemistry/physics background. There is a lot of pressure being applied to the plates. Us crazy hard core creators make these machines work hard for us. My biggest problem is dark cardstock getting embedded in the cut lines, which I just scrub out….need to try the hot steamy water. =) I don’t think the plates were made to last forever as some think. At the end of the day these are cheap machines for what some of us put them through. I just expect to have to replace plates every so often.

[@margueritecampess4991]

Thank you Jennifer and "resident nerd" hubby. I'm going to try this on my warped plates. I'm subscribing as you and your husband saved me from spending money as I'm on a fixed income. Be well and stay safe.

[@mifferss]

awesome! Thanks Jennifer and hubby!! I tried the oven thing last year on a couple warped plates and your hubby is right .... plasticides!!!! i didnt notice any foul odors, but I never used the oven method again cause it really made those plates brittle and one cracked in half while I ran it through my Vagabond! the other kept crackin, and was never the same again.... gonna try this boil method tomorrow!! thanks so much for this awesome vid, Jennifer !!!!!!!

[@arlenepowders4989]

Thank you so much, I just today threw atleast 6 plates in the trash that were warped, needless to say I took them out of the trash can to try this procedure!,, Thank you so much!!!!!!

[@EllyMentryPapercrafting]

I have always done everything you’ve mentioned here using my Gemini full sized machine. It all works well. The only warping I get is in the plastic shim, which I think, over time is inevitable. Thanks for sharing this with those who weren’t aware. I found Ken’s explanation very interesting, I do like to know the reasoning behind things. Nerd 🤣

[@irenedavo3768]

Hello

[@kkrolf2782]

“I do like to know the reasoning behind things”!!! I was always one of those kids who went searching for the “Why”. Can’t remember actually ASKING that question, but maybe by the time I could’ve recalled those events, I probably had been told “Just Because!” often enough to have caused me to go looking for my own answers. My fella says I’ve not changed a lick!!

[@chelliebeaudot7784]

Loved Ken's explanation. I have just enough science background to follow what he was saying, and he has just enough crafter background to use clear language. Another great and timely video, Jennifer!

[@katyratyra]

I can see how the boiling water and pressure would do the trick. Thank you for all the work you did finding a solution.

[@janegotelli7152]

Fantastic video. Thank you. The warping plates drive me crazy. I cannot afford to keep buying new plates constantly.

[@Deneen31]

Wonderful thanks for sharing. I also flip my plates and move the dies around and don’t have much warping. Loved the idea of not putting the background dies in straight I’m gonna do that from now on.

[@patriciaschmitz1619]

Jennifer McGuire you are brilliant. Just saved myself some money, had tried the oven method but it didn’t help, now thanks to you I once again have flat plates. Thanks to your hubby also, for his understandable explanation.

[@LilCraftyNook]

That explanation is so cool!! There is a church in St Ive’s, England with our family seal and special stained glass window! It is fascinating to know that glass always moves. Thanks so much to both of you!! What a team!! 😄🙌🏻

[@irenedavo3768]

Wow! Sounds lovely

[@tc247]

Thanks Jennifer for your months of checking out machines for us and of course your tips. I have all of the Manuel die cutting machines but bc I now have arthritis and it hurts my hands to keep manually rotating those handles I'm buying a electric machine in at the end of this month (Jan 2022) I' ve been leaning towards a Gemini but now I don't know if it should be Anna Griffin's or a Gemini. If there are ladies out there that can give me their opinion if they have either or both I'd appreciate the feedback as this is the LAST one I want to buy. Jennifer, I had to laugh when you introduced your husband as a nerd because I am extremely proud of my physicist/scientist nerd husband and all our nerdy friends. If I don't have an answer one of them will! lol They come in extremely handy. 😁 Please thank your husband because I understood exactly what he was explaining. Thank you too for all the things you share with all of us in the card crafting world. I know I started watching you yrs ago. Take care!

[@jensesanify]

I don't know which one to recommend but there is also a new electric one by Sizzix out that is called the Sizzix Switch. You might want to look into that one as well.

[@judynafus9360]

Thank you so very much for all these tips!! I can’t wait to try them all. Please tell your hubby Thank you for his professional nerdy explanation. That was VERY HELPFUL!!! I just ordered the larger double sided plates for my Gemini. Enjoy your time at the lake!!!!

[@lilyofthevalleysl4990]

Hi Judy how are you getting on with the double sided plates please? Thank you

[@skeletorama1916]

Love it, and thanks to the hubby for the explanation. (Which I didn't think was overly technical, I have to explain non stick cookware coatings to ppl with no materials knowledge, so know it is hard to do...well done!) The plasic additives are also why you should not use nonstick coated pans on high heat, since dangerous things can offgas if you get past a certain temp, like the plates. That is the PFOA thing ppl are on about with those, and it can get nasty. (Offgasses at 600 degrees F, so stick to medium heat) It is similar to your metal cookware, and why you should never add cold water to a hot stainless steel or other metal piece. All that steam looks like you are accomplishing some kind of great cleaning, but in reality is destroying your cookware. Metal is a crystalline structure, so like the cutting plates, heat will relax that structure. As it heats, it will expand and sag, so applying cold water will freeze that structure in whatever configuration it is in when you do....which is how stainless and other metal cookware gets warped, and next to impossible to unwarp. Also why plastic with a crystalline structure would not take it as well, so lucky for us the plates are not! At least with the glass type of plastic, you can reset with heat....wouldn't work as easily with a crystal matrix. :) And is also why waiting for them to cool is the key...it allows them to reset their structural memory to a flat state. Now, off to see if I can rescue some of my old plates...thanks so much for this!!!! :)

[@scrapfuture]

This was such a simple to do fix and I appreciate you sharing it (smoothing out warped plates), Jennifer - plus the sciency explanation. The cathedral fact was SO interesting! Currently have a Sizzix plate in hot water with a saucepan sitting on it. I have just moved house so ditched the really old, warped plates, so was excited to find a warped one, lol.

[@jennifermcguireink]

Glad it was helpful!

[@DianaYeeIng]

I tried the oven but it didn't work so I am there's another method.

[@SarahH-mo2ab]

This proves everyday is a school day. I have been doing the hot water straightening for a while. My enquiring mind loved the explanation from Ken. I will also pass on to my boys the fact about the glass in stain glass window, We will have a look next time we are in church. I’ve always thought it was the way the glass was made. Thank you both for the new and interesting knowledge.

[@rhondahuggins9542]

Jennifer, thank you so much for these low tech, practical solutions! My craft budget can always use a break😉❤

[@jennifermcguireink]

You are so welcome!

[@kahook3883]

Thank you very much for this most informative information. Also thank your husband for his explanation.

[@CraftyKiwiMama]

Great video on preserving and fixing our cutting plates Jennifer! One little tip I'd like to add if I may, which helps make it easy to know when it's time to 'flip' your cutting plate and use the other side, to reduce warping. This is when the centre feels like it's springing up if you put pressure with your finger in the centre of the plate, that's the time to flip it, and cut into the convex side. Essentially, if you rotate your plates regularly, and always cut into the slight convex side (as you know, if you cut a bunch on the same side this happens), this will even the plate back out again. I have Sizzix Big Shot plates and this works really well to extend the life on these. I'm so totally going to try your boiling water and pressure treatment on my very warped eBosser plates though. I bought that machine before leaving the UK and learning the 'rotate regularly' trick! So those plates will benefit from your clever repair trick, thank you so much! Thanks to your hubby too for his fabulous explanation.

[@rosalieridle4675]

Thank you both so much! What a fantastic tip!! 😍

[@MsTcup]

THIS TOTALLY WORKED! I can’t believe how my plate went from trash worthy to nearly perfect. I can’t believe it. Thank you. I was literally gonna toss this. I can’t get over the difference. Again…thank you!!

[@WinnStarr-ov4yf]

Hi Jennifer, my Gemini Jr plates came out so good, it almost looked like new (WOW), my Gemini needed a little more weight in the water so I added a brick and that helped and it came out very straight. That has to be the best tip out there, you saved me from buying new plates and I am very happy about that. Thank you so much. Blessing!

[@905lovest]

The brick was a great idea, WinnStarr 2018!!!

[@elivens1440]

a Thank you Jennifer. Also, thank your husband.. He brought several smiles to my face and I even teared up. Your husband sounds so much like my dad, both in voice and what he said. My dad was a shipping engineer for PPG many years ago. It was a pleasure listening to Ken.

[@annettepearce1690]

Thank you so much Jennifer (and nerdy husband). Love the explanation. Definitely giving the fix a try with my warped Gemini plates.

[@jennifermcguireink]

You are so welcome!

[@juliecruse8029]

I just saw this video this week. I tried the boiling water method and girl, let me tell you, it worked! I had to do it twice, but that's ok. I did sit it outside on a paver and had to place added weight on top of the pan lid. I left it outside for about 45 mins-1hr (only because I forgot it was outside). When I took the pan off (the second time), the cutting plate was as straight as the day I bought it. I'm so jazzed about this method. Thank you!!!

[@vickifinger8670]

I’ve been waiting for this! Thanks to you and Ken for doing this. I tried the oven method previously which only made my plate brittle.

[@jennifermcguireink]

Our pleasure!

[@ramnathlm]

OMG thank you for this. I tried it and my plates are better now. Still a slight warp but barely noticable.

[@56sleepy]

Thank you so much, you paper engineering and crafting goddess! I just love how your mind works, and thanks also to your husband for his engineering presence and expertise. I am off to go try the hot pans with my Spellbinder plates. Hope you had some lake fun after all this work!

[@jennifermcguireink]

You are so welcome!

[@beckyhansen9793]

Thanks for the tips. I accidentally discovered I could unwarp my plates by heating them with my heat gun for a few seconds and then just put some flat weight on them. I was amazed They flattened right out. Didn’t clean them like the boiling water but was fast and easy.