fixing the VFD noise!

  Рет қаралды 19,812

Emmas Spareroom Machineshop

Emmas Spareroom Machineshop

Күн бұрын

Пікірлер: 19
@RRINTHESHOP
@RRINTHESHOP 9 жыл бұрын
I also have adjusted my vfd's carrier freq. By raising the freq, it can cause some overheating. For short run time motors like on a lathe it should not be a problem but if something runs more continuously you have to keep an eye on it. Thanks for sharing, Randy
@ReignOterror
@ReignOterror 9 жыл бұрын
Emma, you have to be very careful about jacking up the carrier frequency. As you increase it, you put more stress on the motor windings. It has to do with leakage inductance. This is why they have inverter rated motors. If you don't have a rated motor, you may be able to getaway with it but you will get more heating in the motor.
@Zorgoban
@Zorgoban 9 жыл бұрын
Yep, the setting 12 was quiet for my ears. 10 is very high but I'm still able to hear it.
@tyhuffman5447
@tyhuffman5447 6 жыл бұрын
Your shifting the frequency of the drive firing to higher in the hearing range. Drives usually fire at 4kHz your adjusting it up.
@tobyw9573
@tobyw9573 7 жыл бұрын
Raising the carrier frequency is said to increase power consumption, but how much can that cost a hobbyist? And are there any other effects?
@RyanWeishalla
@RyanWeishalla 9 жыл бұрын
On the KZbin audio at least, 10 was worse than 8 for me (at least more noticeable at 10 than 8), but 12 was ok.
@jakewynn
@jakewynn 3 жыл бұрын
It was probably in her ultrasound! KZbin compression probably meant it was more audible.
@stephenreeves9025
@stephenreeves9025 9 жыл бұрын
just found your channel from a comment on one of Donald Cossitt's videos I have subscribed
@EmmaRitson
@EmmaRitson 9 жыл бұрын
Stephen Reeves thanks for checking in! hope I upload something to hold your interest!
@stu0things0and0stuff
@stu0things0and0stuff 9 жыл бұрын
Interesting , I found the lower frequencies much better for me, the lowest setting on my HY invertor to make it sound like the IMO drives, my ears are hurting from the higher setting you had it on :) don't worry my brothers a bit deef too so he can't hear it either.
@MichaelEdwards2
@MichaelEdwards2 9 жыл бұрын
Emma, 12 was totally silent on camera. But any ideas what the trade off is on the motor.
@AmateurRedneckWorkshop
@AmateurRedneckWorkshop 9 жыл бұрын
That is outside my experience. I have seen several people with them including mrpete222. Good to see it is quieted down. My ears ring most of the time so I certainly never heard it doing anything. =(;-) If I did I would have thought it was me. thanks for the video.
@MarkThomas123
@MarkThomas123 7 жыл бұрын
Strange.. 12 cleared it up and I could not even hear it.. Came back at 10, but, was not irritating.. I'm sure you are glad it's fixed..Ha..
@marceltimmers1290
@marceltimmers1290 9 жыл бұрын
Hi mate. If you go to Shadon HKW on You tube, you will get a whole bunch of info on VFDs. You might have to hunt them out a little, but they are good. He is also happy to help if you ask. Don't let them tell you that all Chinese VFDs are bad, they are not. It's just the books that come with them that are bad, and first need to be translated by some people of the former Bletchley park. Shhhhh. Marcel.
@EmmaRitson
@EmmaRitson 9 жыл бұрын
Marcel Timmers thanks for that! ill take a look for sure!
@marceltimmers1290
@marceltimmers1290 9 жыл бұрын
Emma Ritson It might also be under Bar Z He is a gruff sort of bloke, but very friendly.
@MankyjsJankyjs
@MankyjsJankyjs Жыл бұрын
Good one didnt now that
Lathe VFD Addendum: How to Tune Acceleration and Braking
16:08
Lathe VFD 3:  How to Fix Noise Problems
21:35
Clough42
Рет қаралды 180 М.
Каха и дочка
00:28
К-Media
Рет қаралды 3,4 МЛН
Une nouvelle voiture pour Noël 🥹
00:28
Nicocapone
Рет қаралды 9 МЛН
Variable Frequency Drives Explained | VFD Basics - Part 1
8:35
MULTIPLE CARRIER VFD FAILURES
12:42
HVACR VIDEOS
Рет қаралды 47 М.
How to Configure your new VFD
7:54
Robert Adair
Рет қаралды 22 М.
What Types of Motors Can Be Used with VFDs?
6:58
eMotors Direct
Рет қаралды 92 М.
How to do a VFD Conversion and Motor Swap for a Lathe
28:27
Phil Vandelay
Рет қаралды 46 М.
Spindle Cable Choice (Eliminate EMI Issues From The Beginning)
14:18
What Is A VFD? (Variable Frequency Drive) HVAC VFD BASICS
4:16
Jumper man Tech
Рет қаралды 10 М.
Каха и дочка
00:28
К-Media
Рет қаралды 3,4 МЛН