this is such a wonderful video and there are so few takers for it . thank u sir ji , lovely information sharing
@nanoblastingАй бұрын
airman 👍
@elisabethp.1160 Жыл бұрын
very interesting for me as a non-pro that is interested in mechanical devices. thanks for sharing!
@mnairengineering1985 Жыл бұрын
Great 👍👍👍👍
@mnairengineering1985 Жыл бұрын
Amazing
@waltermolina34206 жыл бұрын
Very nice..!!!!!!!
@sreejithts97984 жыл бұрын
very good work by experienced technician thanks
@TEDDYKASHIMURA4 жыл бұрын
Sreejith Ts Thanks for watching and support
@gunterweber19722 жыл бұрын
Man sieht im ganzen Video jedoch nicht wo das Laeuferspiel (Spaltmass) eingestellt wird. Ohne das richtige Spiel wird sich der Verdichter bei Erwärmung ( Lastlauf) zerstören.
@MrBookwormik4 жыл бұрын
Starting from 1:42 I recommend to use bearing fitting tools for careful mounting eg. simatec ft33, unless you want to damage the bearing (the most common bearing issues are caused by improper mounting)
@TEDDYKASHIMURA4 жыл бұрын
Michał Kraus thanks for sharing . I’m using the stick is full copper stick, not metal stick. I choose the Cooper because can protect the bearing surface when install . I know this is not the probability tools. Thanks for your reply I will improve the tools when doing the airend
@kerblow20174 жыл бұрын
What is the temperature settings you used in bearing?
@ahammedshohid50443 жыл бұрын
Nice jobs
@eng.mohamedsalematlascopco95305 жыл бұрын
good job
@fixawy3 жыл бұрын
Very good
@omararibi58084 жыл бұрын
Thank for you good job
@TEDDYKASHIMURA4 жыл бұрын
thanks
@bobbyrahardja44965 жыл бұрын
Thank you
@donkeydammer80833 жыл бұрын
Hi sir, wanna ask about how u dismantle the cylindrical roller bearing?
@seong6273 жыл бұрын
May I know where can I learn how to service and overhaul air compressor in Malaysia?
@qulute2 жыл бұрын
There is one hole fitted with alenkey bolt what is the uses of that hole please can you tel me sir?
@silvonetevitorio74274 жыл бұрын
bom trabalho obrigado por nos mostrar seu trabalho bem feito isso que vc jateia ai no parafusso como chama onde podemos comprar
@ronissonsilvestre92853 жыл бұрын
Bom dia. Acredito que seja lixa d'água.
@ganeshkamathsampe47083 жыл бұрын
Why heating bearings and gears when assembling and at what temperature? what is the name of heating equipment? please pardon me for asking
@TEDDYKASHIMURA3 жыл бұрын
when need to remove used old bearing must heat the metal . If you no heat the metal too difficult to remove. Puller special tools also can remove the gear and bearing , but will spoil the metal shaft surface. install a new bearing also need to heat the bearing , because you heat the bearing the bearing hole will increase the size. after install the bearing cooling down will going back the original size. Heat will increase the size . Cool will decrease the size. different size bearing different timing and tempeture.
@michaeljaypernes24085 жыл бұрын
Hi. Any possibility I can learn how to overhaul an air end through your program?
@TEDDYKASHIMURA4 жыл бұрын
Michael Jay Pernes I will try my best when I overhaul the AIREND and taking the video thanks for support
@josemiguelesquibelperez11562 жыл бұрын
I can be considered in the 25μm to 50μm High Pressure discharge clearance, to 100μm to 150μm, low pressure suction clearance for AIRREND ELGI, please tell me about these clearance. I have a problem with a compressor because it was necessary to change the bearings because these don't work and the screws suffered many scratches. Please support if the clearances gives are a good option to improve the vibrations in our device.
@AntonioRamirez-eu9kx7 ай бұрын
it must be 0.009 "
@marbiella6 жыл бұрын
good video. where can I find a manual about repairing airend??
@TEDDYKASHIMURA4 жыл бұрын
Marbi25 what model AIREND you want to overhaul?
@ratneshk.compressiorborewe39473 жыл бұрын
Pls vedio normal.
@ratneshk.compressiorborewe39473 жыл бұрын
Atlas 1200-330 airend overhoul mannual provid me.
@pakmunsoo39752 жыл бұрын
What is the machine you use for the bearings at 2:12? It heats up the bearing?
@TEDDYKASHIMURA2 жыл бұрын
SKF Brand bearing heater
@osanchesorebe90864 жыл бұрын
porque o vídeo não esta na velocidade normal afinal amigo você queria mostrar o que ?
@Sid97032 жыл бұрын
You put too much high temp silicon gasket, I suggest to use loctite 518
@TEDDYKASHIMURA2 жыл бұрын
Thanks For Comments. Now we Using Loctitle gum already red color ..
@zakymubarok52274 жыл бұрын
Kalau overhoul kompresor denyo 390 bisa gak bos? Mesin saya posisi di Semarang. Thanks
@TEDDYKASHIMURA4 жыл бұрын
You want overhaul AIREND or engine this Denyo 390
@rmtm7460 Жыл бұрын
Sleeping now
@mamamelaverga87533 жыл бұрын
It's not a good reparation.. You sould use paper gasket with the according thickness to maintain the compresion chamber measure, if you use joint paste you are changing the total length and will be problems.. Take care
@TEDDYKASHIMURA3 жыл бұрын
Mamame Laverga thanks your sharing🤝
@shankarvaishnav754 жыл бұрын
Elgi.450/150.repreng.bareng.number.dala
@refanafandisniper86865 жыл бұрын
Kalau ngatasi masalah temperatur tinggi/ oli gak mau naik bagaimana mas...
@Od13ok4 жыл бұрын
Refan Afandi sniper merk apa bos? bs di bantu email od13ok@gmail.com 😅
@TEDDYKASHIMURA4 жыл бұрын
When high compressor oil temperature have this few reason , maybe the radiator cooler dirty ? Fan belt condition not good ? Or Compressor oil thermostat problem etc ....
@comvietnam56596 жыл бұрын
The first of NU* inner bearing too hight temperature.
@TEDDYKASHIMURA6 жыл бұрын
Lu Van Com I follow Japan original bearing parts. Next time I try using another bearing... thanks for recommended
@rumahkuburmarimasuk74814 жыл бұрын
Comproser model 390s kalau untuk minyak apa yang perlu di isi di dalam gear itu
@TEDDYKASHIMURA4 жыл бұрын
Shell Corena oil Rs32 Mobil Rarus 424 Faircol RA32
@TEDDYKASHIMURA4 жыл бұрын
Total Fluidmatic IIIG Automatic Transmission Fluid