FlightLine 30A ESC Programming Guide - Audible Beeps - Motion RC

[@steveniovinelli2176]

22 tones!! insanity!

[@patxi6228]

Thanks, thanks, thanks. Very useful for my esc EP30 Volantex. Thanks from Donostia-Spain

[@FasterThanJesus666]

is this the same esc, just rebranded???

[@patxi6228]

@@FasterThanJesus666 listen to the complete sequence of beeps, if it matches those of the image it could be the same.

[@ewerninghaus]

Great video, thanks! Nowhere else to be found in the internet, saved me. My ESC is a rebrand, but the tones for programming are exactly the same. What it does different is it beeps twice to confirm item selected and it does not rearms the ESC. So after programming you must unplug and plug in again.

[@illuminatorix]

Hello and then you for this video! May I ask if you are using a spektrum RX with SAFE-AS3X mode? If yes is there any settings you recommend? Than you!

[@ItAintMeBabe99]

Good video. So, is there anyway to know what the “function settings” are set to ? For example, Battery Type. Is it set to NIMH or LIPO, or do I have to set all 22 functions. That would be sitting there and listening to thousands of beeps (tones). Is there a default list ?

[@cloudyifr]

Great video and worked flawlessly! I have the P51 too. On an unrelated question you mention brake OFF but I'm told brake should be ON. I'm breaking a prop on landing about every other flight. I'm landing on a fabric runway. Thanks!

[@foamerbird]

Hello, thanks for posting the video! The beep demo run-through is quite helpful. Would you please illuminate me, what is the translation for "angle of entrance". Is that for motor timing?

[@tariqyounus3880]

First of all very good video . highly appreciate. Can we use this chart for hobby wing , volantex and other esc ? Or only this chart for volantex esc . Pls guide

[@MotionRC]

I am not sure about other brands

[@hifinsword]

Great video on the tones. I have a question about the BEC for this ESC. What is the BEC output in volts and amps?

[@ewerninghaus]

The BEC is simply turning the motor off or reducing the output power solely based on battery voltage. As soon as the battery undervoltage is reached (at middle it was 3,2V per cell in my ESC) the protection system triggers and you motor stops. You need to go to minimum throttle again for the system to rearm.

[@arrowflyte2]

Mustang came with brake on....so very helpful. Thanks!

[@maverik314]

Hello James, I'm a french pilot very good video . I bought a Arrow Corsair F4U 1100 PNP and during the maiden fly i notice i don't have full power. I have to calibrate the ESC but i don't know the name of the ESC. i watch your video : Esc calibration Quick Tip i try to do the same thing but this don't work. Can you tell me the procedure to follow with this ESC please? Thank you soo much.

[@vickybanate]

I've a 20 A flighline brushless ESC..i'm having trouble finding the chart for that..could you please help me in this?

[@MotionRC]

Beeps should be the same as this one

[@theodorebraxton4509]

I realize I'm quite randomly asking but does anyone know of a good site to stream newly released movies online ?

[@kyreebrixton8630]

@Theodore Braxton I watch on Flixzone. You can find it on google :)

[@nathanielcullen1472]

@Kyree Brixton Yea, I've been using flixzone for months myself =)

[@theodorebraxton4509]

@Kyree Brixton thank you, signed up and it seems like they got a lot of movies there =) I really appreciate it !

[@michaelromingerjr6513]

I inadvertently set the brake on the Flightline spitfire esc and I'm havimg trouble turning it off or doing a factory reset. Do these same instructions and tones apply to its esc as well? I'm getting different tones and I'm having trouble resetting it. Any help would be much appreciated!

[@arinzei.7496]

Very helpful, thanks.

[@rcshenanigans2734]

THANK YOU!

[@tariqyounus3880]

High dear could you please help to guide ,how I can restore factory settings of volantex esc ? I could not find manual on net . If u know link pls share

[@Shinkaaaa]

Does someone know what "Startup of Motor" means? Can't find any explanation

[@olgoz1]

Thanks for the video. It's the same parameters menu and tones for my "Surpass Hobby" ESC.. But I can't get into the settings. ESC is soldered on to board. I am running INAV. And DJI Digital FPV Air Unit...

[@MotionRC]

Not sure what to say here. Best bet is post this in the HobbySquawk forums and the community can try and help you

[@olgoz1]

Thanks I'm sorted. In INAV configurator, with my flight controller plugged-in, I can set throttle to 100% - and then plug-in my LiPo. Everything else is as per your awesome video. Thanks again.

[@clausberner5300]

Thanks man. Seems to work for amewi big Storm 60a esc also.

[@ross5307]

When I to reset my esc with tx off and throttle up, I battery up the tx, plug in the battery, snd immediately get a “high throttle warning.” What am I doing wrong

[@MotionRC]

Leave your TX on. Unplug the plane, with the TX on, put throttle to max, then plug in plane

[@notanrcguy]

I have just purchased this same esc. I am able to engage the programing but my motor does not turn forward nor backward. If I turn everything on it just beeps with no functions.

[@dalekelley3003]

Same problem, my motor won't turn

[@Thrall123RealID]

Does this FlightLine 30A ESC support a $15 programming card? I'll never keep track of that many tones.

[@MotionRC]

with this video you dont have to. Just listen to the tone on the video of what you want to control and wait for it on yours

[@ewerninghaus]

I sincronize the video with the tones, so I don't even need to listen to the tones. When the menu item I need is highlighted on the video I flip the throttle.

[@mepropwash]

where can I find a copy of this 30a guide? where can I find a copy of the other flightline ESC's

[@MotionRC]

This video will work for all FlightLine ESCs. The Tones are the same

[@bpt1231]

Hi, after setting the brake then if we want to continue programing and to choose the battery type, do we need to unplug the battery, bring the throttle full up and do the same procedure. Any help please. Thanks.

[@MotionRC]

Yes. Repeat the process for any changes you want to make. One at a time

[@bpt1231]

@@MotionRC one at a time that is confusing. After choosing one item and to choose any other item We need to unplug the battery , bring the throttle full up and wait for the the particular beep and then bring the throttle down. I am correct?

[@MotionRC]

@@bpt1231 yes, because when you bring the throttle down after any setting change, the esc will arm. So the only way to do it is one setting at a time

[@LigthningII]

Got it and thanks

[@MotionRC]

Good Major. Glad to hear it!

[@LigthningII]

@@MotionRC I must admit that I am show at times. Must be this aging thing:).

[@55amps]

When I arm my quad .. my throttle is on the right instead of my left . And it’s on mode 2

[@MotionRC]

Call whoever you bought it from. We don't sell quads and this video has nothing to do with quads

[@55amps]

@@MotionRC quadcopter, drone , Multi-Rotor etc ur such a noob!! No disrespect! But yea 🤣🤣

[@MotionRC]

@@55amps ? This video is for an ESC, our website doesn't carry any multirotors, drone etc. So I have no idea how to answer your question as I don't even know what product you are referring to. Ask the customer service from where you bought your product

[@sadsausage2224]

Can you do this with any transmitter?

[@MotionRC]

Yes. It's a function of the ESC itself not the specific transmitter

[@cozzy206]

Thanks

[@RCREVIEWS101]

L A M E from the factory to not check it and just throw the ESC in the plane and on top of that just send without any ESC instructions in the box, my ESC had brakes ON and set for NIMH and wrong rotation.....when I first plugged in with a 3S I only heard one tone, weird...than found out everything else. I better stick with Freewing, never had a problem with their planes

[@jamiriehoward3157]

I'm guessing I'm having the same issue as you lol 😆

[@dariusdariukas3245]

F*****g difficult program, I need to change that s***t....

[@lewisdavis2526]

I can't even get my motor to run or get to program.

[@dalekelley3003]

Same problem

[@ewerninghaus]

I had some difficulty in the beginning, Motor stand still no matter what. Found out I needed to calibrate the throttle position as first action, afterwards it worked as intended.

[@majoryusuf8914]

I GOT tone16 and it twitches and esc gets hot

[@MotionRC]

Can you explain a little further? What twitches? Tone 16 is for a helicopter so you wouldn't want to put this esc in that mode on a plane

[@majoryusuf8914]

@@MotionRC it startet to get hot know it won’t even beep ore twitch completely dead silent

[@robbiedavis72]

I'm more confused than I was before I seen this video... you guys have no idea on how to explain this crap..

[@MotionRC]

What are you confused about? What are you trying to accomplish with the ESC?

[@thorvelasco1467]

Lifesaver !