Всё хорошо, кроме одного!) Армирование должно быть, как минимум, в нижней трети стяжки! Сетку следовало бы приподнять на 2-3 см !)
@iambobby35376 жыл бұрын
So many videos with, no narration, are bedded with bad music. Love this sound.
@zurzurshahean62626 жыл бұрын
عمل رائع وكامل اتوقع نتائج ممتازة و ناجحة جيد انه لم يستعمل البيتومين و لفائف العزل شكرا لك مقطع مفيد
@stefanrudolf64776 жыл бұрын
Kommt die Armierung nicht in die Mitte des Unterlagsboden?
@udos.29876 жыл бұрын
nein, wieso?
@stefanguido65466 жыл бұрын
Hängt vom Lastfall ab.
@stefanguido65466 жыл бұрын
Stimmt, da unten macht sie überhaupt keinen Sinn. 1/3 Überdeckung. Entweder oben oder unten. So hätte der gute Mann einen 100€ Schein in die (zu dünne) Brühe werfen können, wäre genauso sinnvoll.lol.
@andreasmuller79326 жыл бұрын
In der Mitte ist die statische Nulllinie, also ist da die Armierung weggeschmissenes Geld. Sie muß ins untere Drittel, dort treten die Zugkräfte auf.
@f.dortmund45935 жыл бұрын
In dem Video ist einiges nicht nach der anerkannten Regel der Technik gemacht worden. 1. Randstreifen tackern ist ok, aber man sollte an die Schallübertragung denken. Dann sollte man diese nach dem verlegen der Fliesen erst abschneiden. 2.Dämmung nicht versetzt verlegt! 3. AKS Gitter zu tief und zu nah an der Wand ( man sollte etwas Luft lassen)!
@MrJFoster19846 жыл бұрын
Flexible adhesive and grout instead?
@erissonmedeiro75175 жыл бұрын
Mostras seus equipamentos e onde você comprou eles
@pauldhennessey6 жыл бұрын
nice job but seems like dry pack would be much easier
@chriscutting57735 жыл бұрын
Jesus christ he made that look like hard work
@frankdosantos16 жыл бұрын
I'm not faulting his workmanship, but why all of that just to pour a screed?
@euroovca254 жыл бұрын
should have gone with dry concrete instead of wet.. would have been 100 times easier and less messy, also less prompt to cracks
@garryfwright6 жыл бұрын
He should have used a semi-dry mix of sand and cement rather than a self leveling compound. Self leveling is meant to correct small deviations in floor height, typically less than 10mm. Sand and cement is much cheaper but requires more skill to implement. Im a plasterer and use it all the time. His prep was very good but I suspect he is a joiner rather than a professional floor screeder. Thanks for posting I learned something from it.
@kevinhornbuckle6 жыл бұрын
Garry Wright The mesh was pushed to the bottom. Where is the water supposed to go if he's pouring on plastic? This was painful to watch.
@MrMalarix6 жыл бұрын
It doesnt seem to me be a self leveling compound, but I could be wrong, other than that it's ok
@nuirueu6 жыл бұрын
There's a few companys that make compund that can do up to 50mm in one pour nowadays to be fair. But i would never use it on a chipboard floor even with that feeble wire he put under it.
@maafumataele6 жыл бұрын
Hi sand and cement is better materials for that floor screeded but floor level compounds that the wrong materials for that job/ gib board is wet and starting damaged /finishing the floor is not good enough still rough and more cleaning up /prep works all good enough I think you are builder not a solid plastering thanks you very much you done the job but I am learning what you doing and you learn on my comments cheers brother
@scwfan086 жыл бұрын
He didn't use self-levelling compound. He used Estrich (screed) which is exactly what you said but he definitely made it way too wet.
@Anoncore16 жыл бұрын
Aside from using this type of concrete for a more then 1/2 application ,the prep was impeccable , a little over the top , but great job....mesh ,this type has to be pulled off the ground to be doing its job , and not proper again for this type of mortar or ciment what ever you want to call it. Why so thick tho? 3/4 substrate is more then enough for code in my neck of the wood....anyway , in the end , love the attention to detail , minus final choice of material for levelling .
@mzmgla4 жыл бұрын
na ob da der wasserzementwert stimmt ! ?
@SOPM6 жыл бұрын
You guys were making comments criticizing him can’t criticize him. Where is your video. And then look at your ratings on your video. Then come back and comment and show the link on your video. The customer made you not want to pay for heated floors. This was a video. The time it took to do what he did is about the same amount of time it would’ve taken to put concrete on top of wood. Insulating the floor reduce the Cement and gave more “stability” to the floor overall if the floor was to be changed or drop down in height. He created (( “versatility.” )) But you lame contractors did not think of that. The guy in this video did a great job. Keep up the good work.
@cncsdaddy855 жыл бұрын
I've seen this method used for movement and weight purposes as well as cardboard forms used for large build ups most of the guys commenting negatively have never seen a commercial job or been critiqued by anyone else other than a homeowner who know no better
@sandorkolesza37435 жыл бұрын
Why He laid that reinforcement screen? Should ift up at least 1 cm! (otherwise useless!)
@micko60414 жыл бұрын
Mai e poi mai farei un massetto in quelle condizioni avrà fatto una fatica da bestia
@rosariozappavigna32634 жыл бұрын
È un pasticcione.
@РыбакСибирь6 жыл бұрын
Единственное в жизни что все бы хотели, так это делать ремонт с такой скоростью:-)))
@pedromunoz22256 жыл бұрын
👍👏👏👏👏👏
@DanielJuniorSilvaSantos5 жыл бұрын
NÃO AO COMUNISMO!!!!
@Framewood5 жыл бұрын
x2 рулит
@olegotdelka375 жыл бұрын
Это што за хуйню он тут делает ? И не песко бетон и не налевной. Нахуя ?
@PiratDim5 жыл бұрын
@@olegotdelka37 как раз стяжку и делает. глянь, что такое у него в мешке- baumit EB 42
@daanvreugdenhil6 жыл бұрын
Due to the speed of this video, it sounds a lot alike Scrat, the Sabre-Tooth Squirrel from Ice Age, Sniffin' around with his acorn...
@nially856 жыл бұрын
How did u even think of this?but sooo correct!!! Pmsl
@JoaoPereira-gz2zc6 жыл бұрын
You know what I did? Sped it up to 2x. Awesome
@chukwow57385 жыл бұрын
Hahaha yes, that was my thought also. Had to go to the comment section to see if it was only me LOL
@Chelovik_NZ5 жыл бұрын
Or Benny Hill ... it only needed the music to make it so .... however, it was a good watch and I did learn a few tips
@tonygibbs98216 жыл бұрын
If this is an embarrassing standard of work, then I'm afraid a majority of professionals of their trade should be thoroughly embarrassed!
@Maxmustermann-e8i5 жыл бұрын
@@tonygibbs9821 I'm pretty sure the title is the result of a bad automatic translation. Nobody wants to embarrass the guy. Some of the comments are unfortunate tho'.
@DanielR5775 жыл бұрын
The screed used is Baumit Estrick EB 42 which is a dry type of screed with only 4 liters / 35kg pack, not a self leveling liquid type, hence the decomposing when mixed and poured out like a selfe leveling liquid type of screed. This is printed on every package. When prepared properly the screed is described as a stiff to plastically/kneadable composition. If the majority of professionals is applying great and expensive material is such a way they should be thoroghly embarrassed. ch.baumit.com/produkte/estriche_boden/estriche/baumit-estrich-eb-42.html
@Ewoodster4 жыл бұрын
This is translated from German and "Bad" means bathroom in German. It has nothing to do with bad work, he is dong just fine as you pointed out already.
@fabio340215 жыл бұрын
ma chi ti ha imparato a lavorare ahahah
@SST234 жыл бұрын
everything was ''ok'' until he tries to level the floor...omg.
@0815SeaBass5 жыл бұрын
Alter Schwede, machst das aber extrem aufwendig und umständlich, für ein paar qm Estrich. Letzte Woche habe ich 15 qm Estrich ins Bad eingebracht. Sogar noch selbst mit dem Mischer (Rheinsand und Trasszement) erdfeucht angemischt, mit der Karre rein gefahren und mit der Latte sauber verdichtet und abgezogen. Das ganze hat 3,5 Stunden gedauert.
@adangerousidiot6 жыл бұрын
I don't understand these comments that he's done a naff job. He has done a good job, I suppose he finishing off with tiles.... Personally I don't like it's all in the bag mixes......never heard off a screed bag mix. I think he was using postcrete .;o ) I'm self employed and always work on a price, so on his side. It's easy for anonymous people slag everything off, fair comment is good but don't bad mouth just for sale of it. What you people out there think. Regards to you all
@armandodemichele14206 жыл бұрын
adangerousidiot, The end result is good, in the end I guess that's all that matters. I am a master tile-setter, I install tile marble, slate, and also terrazzo. Many newer installers do it this way, but I know the old ways of the trade. I mix the sand and cement myself, and I don't waste time with those leveling ties on the walls , and that is because of the cement and sand ratio I use has less water, and holds up. It is very difficult to write and explain my method here. I think he did a good job, even though he would go broke around my parts of the world with this method if it takes him more than 3 hours to do this job ( alone with no helper).
@aynurylmaz31236 жыл бұрын
Başlıktan bi b*k anlamayan bi benmiyim 🤔🤔🤔
@gilgilofgil54766 жыл бұрын
2 малярных маяка 20 минут работы - качество тоже самое (прикольная задумка с приспособой для выставления лазера)
@mariocapuleti86185 жыл бұрын
Ano i vidna shto u vas v Rassii kacestva lutshe cem v Italii ...... nu vy i pridurki kaneshna ... 2 maliarnyh maeka 🤣🤣
@SaratovFilm5 жыл бұрын
@@mariocapuleti8618 Качество везде на самых разный уровнях. Придурков и у вас хватает, поаккуратнее с ярлыками.
@alessandrolucidi27855 жыл бұрын
Grande cazzata
@rosariozappavigna32634 жыл бұрын
Questo non sa manco cos'è una cazzuola.
@Bosoiy6 жыл бұрын
для лучшей работы сетки было б неплохо под неё подложить закладки и сделать слой сетки в середине заливаемого раствора.. И саму стяжку разделить на 3 сектора демпфером..
@ivanovaleksandr99656 жыл бұрын
Ну и логика у тебя, куклин. То ты кладеш сетку в середине, чтобы стяжка была одной целой, а потом демпфером хочешь разделить её на три части. В данном случае сетка отлично выполняет свои функции (предотвращает от разделения единой стяжки на несколько частей). Не обязательно класть сетку именно в центр стяжки, а желательно положить в нижней части.
@rotmensrrrotmensrr9246 жыл бұрын
Для сетки нужно 1-2см защитного слоя....
@rotmensrrrotmensrr9246 жыл бұрын
Клоун тот кто етого незнает)))))))))))))))))))))))))))))))))))))
@Bosoiy6 жыл бұрын
бетон хорошо себя ведёт при зжатии,при растяжении для того,что бы он остался целым ему необходима арматура.Чем больший кусок стяжки (или бетона)есть-тем больший температурный коэфициент (растяжения-сжатия )на него воздействует. Разделение стяжки на зоны способствует сохранению целостности структуры сделанного изделия в более длинный период нежели дожить до зарплаты.
@Vasily-g4u4 жыл бұрын
Мудрые советы, тот кто слышит тот поймёт.
@davidfernandez89524 жыл бұрын
Que desastre de tío no tiene ni idea de hechar autonivelante
@R0B0PR0P5 жыл бұрын
At this point the client decides they want UFH or the spark remembers he didn't lay a cable 😂
@kleos_drywall5 жыл бұрын
Love the knee trolley he's on
@ianmcintyre64986 жыл бұрын
I think he's done a great job - Well done !!
@Stop..carry-on6 жыл бұрын
No mask mixing
@AMLO-4TA.TRANSFORMACION5 жыл бұрын
Man I just notice that he started working when it was daylight and he ended with a not so hot lamp, lets give the man a hand. With no help and no real tools and maybe no Home Depot around.😭 I know, that sucks.
@enverkement5344 жыл бұрын
11qq
@ckdigwal37676 жыл бұрын
You have the best job work master but please use safety and precaution And use a dust mask. Thank you.
@edwardmcgarry79176 жыл бұрын
most excellent job completed by a solitary professional
@johncoops68976 жыл бұрын
Wrong. It's probably the most UNPROFFESSIONAL attempt at levelling a floor that most builders have ever seen. There is so many mistakes it's not funny. Having enough money to buy a cheap laser level and a metal rail for your circular saw does not mean anything whatsoever about the quality of the result.
@richardsimpson31365 жыл бұрын
Have to agree with that Edward!
@totoleheros75065 жыл бұрын
@@johncoops6897 maybe you are right with the unprofessional, I don't know. But you are wrong with the cheap metal rail for his circular saw. Have you ever seen how much this Festool saw and rail cost? Far to be cheap, it is top end tools.
@johncoops68975 жыл бұрын
@@totoleheros7506 My word "cheap" related to the laser level. Yes, I know that those rails are expensive, however my point is that no matter HOW much equipment you use and how much time you waste, this is not the correct way to do this task. It doesn't NEED to be level... in fact the entire point of such a wet area floor is to not have it level, but to have a fall towards a drain. Also, the final surface levels and flatness are sorted out by the tilers, who place the tiles on a 3 to 10mm thick bed of adhesive. They set the levels on the *tops+* of the tiles, not the bottom, and it doesn't matter whether the underfloor is perfectly smooth or flat. It's a total waste of time to create an underfloor at 0.1mm accuracy when the following trade doesn't even use that surface as a reference point.
@Hey_me4 жыл бұрын
You all in here saying shit instead of giving the man thumb up for a job well done.
@nobodyspecial81274 жыл бұрын
Agree this dude is the master
@MM20095 жыл бұрын
personally I would've lift the mesh of the floor...
@s00128234 жыл бұрын
That is critical indeed, now it doesn't have any function. Other point is that the concrete isn't mixed proper. The preparations were great! I guess he was learning as well.. Thanx for the video, I learned a lot!
@metallitech4 жыл бұрын
@@s0012823 The underside is under tension when load is on top, so I don't think it has no function. That said I would also have lifted it.
@s00128234 жыл бұрын
@@metallitech The steel will corrode when it is too close to the bottom. I must be >2-3cm.
@mikejohnson91184 жыл бұрын
could have used bits of the mesh to lift it off the floor. Or bent the sides down like feet. Even a .5" would have been better.
@ringoglassner71495 жыл бұрын
Should the mesh not be more in the middle of the floor levering compound instead of hard down, but other than that he did a good job great work.
@ZingaraJoe5 жыл бұрын
As steel is great in tension and concrete is good for compression, the mesh would be best raised slightly off the floor on some little chips of stone, cement or 'chairs' so that it has a good protective layer of grout/concrete under the steel mesh to protect from corrosion but well down from the top surface.
@krzysiekm16413 жыл бұрын
Egal wie gut du deine Arbeit gemacht hast, Der Cheff wird immer zu dir sagen dass es schneller und besser hätte sein können
@Smitwwwwww5 жыл бұрын
3:48 что за тачка для коленей?? как правильно называется?? наверное очень удобная вещь!
@JP-nb7tm6 жыл бұрын
Give him ten years breathing that dust in and he wont be doing anymore bathrooms
@zoki.to9746 жыл бұрын
you do realize millions of workers used to work with concrete for hundreds of years without respirators? not for 10 but whole working life, 20-30-40 years...
@MrHBSoftware6 жыл бұрын
Jp you are good at predicting the future? so what are you doing here?
@rosesousa12455 жыл бұрын
Hugo B.
@ravagekillz5 жыл бұрын
smartboy
@concreteblockmakingmachine47655 жыл бұрын
kzbin.info/www/bejne/bHuonYNnoa1_oZY
@STT75754 жыл бұрын
У нас что в мире прогнозируется похолодание ??? Все утепляются как в крайний север или это камеру пыток готовят ??? Чтоб шум поглощал ???
@sweetiepienumber16 жыл бұрын
He's fast! He's got good tools. He's done this before. And that = getting paid here in the U.S.
@arpadprp17786 жыл бұрын
How about guarantee..
@putusutama6 жыл бұрын
@@arpadprp1778 no guarantee 🤗😂
@luketutolo4 жыл бұрын
What a waste of time
@NilsAlbertsson6 жыл бұрын
*By fuck, you're not paid by tbe hour, are you!!!* *An English workman would've taken two weeks, charged three times as much, knicked half the stuff for another job, and spent 80% of the rest of the time pestering the owner for advances, material costs, and cups of tea for when he's reading the Daily Mail's stories about European workers **_"stealing"_** jobs like this off him!*
@timichpyatigorsk90936 жыл бұрын
Чето както не очень.
@geoffreywright47195 жыл бұрын
These self leveling compounds are very difficult to work with inasmuch as the two products I've tried recently do not actually "self level" and they harden very quickly. Furthermore, the working time is hampered by the product being very sticky so metal trowels pull the material and deform the surface. Try using a "magic trowel" which has a rubber edge and looks like a squeegy. Screeding is essential IMO but you will not find this permanent forming apparatus at Home Depot. This video does not show how the far right corner was leveled...if at all. You need a straight edge that reaches all the way across your work (so both long and short). You should pour all the material at once or as fast as you can mix 5 gallon buckets. (Video looks like at least two 60 lb sacks in a 10+ gal bucket but 5 gal buckets are all that one person can really handle unless you can find a gimbled drum with wheels for large areas.) If you pour up against drywall without sealing the crack at the floor, the leveler will seep under the drywall, mud sill and into any other hole or crevice it can find and leave a depression in your ff (finished floor). I like to pour in lifts or levels but that means raising the whole area at the same rate, not trying to join areas (and don't forget the primer: read the directions). Use a heavy duty drill motor (hole hawg), put the water and paddle into the bucket first then empty the sack on top. Do some more homework on this material and watch the process in person if possible. Good luck!
@johnmehaffey99536 жыл бұрын
It would make a floor screeder weep when ever I saw any professional screeder in action it was a semi dry mix and then screeded, then done with a wooden or plastic float to get a finish, never in all my days in construction have I ever seen a floor put down this way
@stephbhoy16 жыл бұрын
Agreed. If he's goin to mix it so wet, then use self levelling compound then there's no need for a straight edge.
@jorgeguanche53276 жыл бұрын
How to do it wrong......Jesús christ!
@zorroonmilkavitch18406 жыл бұрын
@@stephbhoy1 pretty sure that's self leveling compound with price pretty high much cheaper to go with this mix
@darrenkaspers93315 жыл бұрын
Wrong, can't use self leveling compound it's too deep, you'd need a few hits at it, with wet gear like that, once levelled and going off it needs a steel trowel finish. But let's be honest he done it all wrong lol
@darrenkaspers93315 жыл бұрын
@Glyn Owen I've never seen it, only selfleveling you have to mix with sharp sand to bulk it up. Also as the gear he's used is do wet the drying time would be over a month before a floor covering could be put down.
@jimcheney15555 жыл бұрын
What country did this take place in? 2nd floor and above installation? Foam board? No floor lath? Way too watery mud? What was the purpose of making this video? Was it to show how NOT to do a floor?
@tonyomalley9016 жыл бұрын
Why raise the floor? He has just created a step up into the bathroom! Why the insulation? it's not needed on a wooden floor! If you have to insulate and screed the floor why not install underfloor heating Rather a pointless vid
@thesunreport6 жыл бұрын
I'm guessing it's going to be a wet room and there wasn't any room for the drains if the floor wasn't raised??
@nellyishtari6 жыл бұрын
The whole house is renovated, so all floors will be insulated.... Floor heating in a bathroom isn't necessary, you don't need a permanent heating system, but a fast warm up when you use it. And why insulation? because insulation regulation requires it for eco labels and also if watching other vids, it's an old farm renovated, the floor isn't on crawlspace but directly on ground, which adds thermo leaks.
@dutchymon6 жыл бұрын
They do not do construction the easy way in Germany, and they don't wear gloves or dust masks either because this would make workers too comfortable.
@augenbutter6 жыл бұрын
all the rest of the floors will be done, is my guess
@mymorristribe6 жыл бұрын
Didn't you see the pipes he was trying to cover up that ran on top of the wooden floor. That's why he raised it.
@reza12193 жыл бұрын
wtf did he do.....that was allooott of extra unnecessary work to screed a floor when he could have used sand cement mix and it would have took couple of hours!! and btw you wear earmuffs to protect your ears from the sound of a drill but won't wear dust mask to protect your lungs from silica dust smh lol!!!
@ZergRadio6 жыл бұрын
And after 2 weeks the floor falls through to the apartment below lmao :P
@mr.waffle97366 жыл бұрын
why?
@ThisIsSolution6 жыл бұрын
@@mr.waffle9736 25000000 lbs of mix on a 1/2 plywood subfloor with 2ft on center floor joists
@xelarian2896 жыл бұрын
Cheapest quality, Just for joke. I think he build for sale, not for his
@retiree10336 жыл бұрын
Probably on Beam and Block (look it up) with 100mm closed cell foam insulating layer overlayed with OSB. A common floor system. You'd be surprised how much weight that would support. Don't assume that floor is the same as you'd build.
@ZergRadio6 жыл бұрын
+Thor The Northern I once saw a very dry piece of turd stranded in the desert, it has absolutely NO sense of humour.
@Ray-pt5su5 жыл бұрын
I'm really angry to see that! Do you sick of living? To breath that concrete dust is really bad for you! Use a air filters cost just 10$ max! What the heck are you thinking about? *USE IT NOW*
@nonyabuisness6 жыл бұрын
He did everything perfect.... until the concrete
@jokisha9992 жыл бұрын
To much work for a simple thing. Normal estrich, then selfleveling… if is needed.
@adangerousidiot6 жыл бұрын
I agree with grumpy, the guy did a nice job in difficult circumstances. I've been in building trade 40+ years been there many times. Job underpriced just to get the work...All these bullshit videos showing the perfect job, pity the they don't let the viewer know the price
@philipp37716 жыл бұрын
This Guy did not a nice Job, sry.... My English is a little bit poor to explain - I´ve seen so many mistakes in this Vid. Many of planning his work, much more of doing it! But his worst Case is the among of water im "Estrichbeton"! Lightconcrete? No Matter, there a lot of concrete-mixes out. After 40+ years, i think U know this. where Do you come from? I´m from germany, we have a rule for every nails, you want to bring in..... We are the founders of clean-diesel ;-)))) Friendly Regards, Philipp
@KugleeKuglee5 жыл бұрын
@@philipp3771 plan good less work and less error....
@specialistscreeding66005 жыл бұрын
You can't scrimp when it comes to floor, it's a very permanent part of the build and this is just unprofessional and shoddy and will cost more money to repair after when it needs latexing
@KugleeKuglee5 жыл бұрын
@@specialistscreeding6600 Why do you need repair? (Brick/concrete building has this type of floor in Europe and I never heard in my life any repairing about this.)
@specialistscreeding66005 жыл бұрын
@@KugleeKuglee if I done a job like this I wouldn't be in business longer than a day. It's terrible, lumpy and needs layering or a tiler wouldn't go near it
@MrHBSoftware6 жыл бұрын
The title is Portuguese and translated to English is something like "Table of floor spill bath ashamed leveling" what the fuck :)
@cristomario91186 жыл бұрын
i have seen "professional" doing a crapper job!
@cristomario91185 жыл бұрын
...only get "professionals" like you in the US and UK
@alexpsk17845 жыл бұрын
Stfu mozzarella head
@cristomario91185 жыл бұрын
Alex psk fuck you to you piece of shit!
@Spatzenterror5 жыл бұрын
@@cristomario9118 this are true german "professionals". btw. great idea but poor details.
@orcaazur065 ай бұрын
This man allways have great videos. Just one question : is it estrih ?? 👍
@davemeraz51176 жыл бұрын
Don't know, thought I saw crack ;)
@ayhansurekli77292 жыл бұрын
Oğlum çatalın gözüküyor...:)
@valendorn6 жыл бұрын
так и не понял, почему ванная смущенная))
@Альберт_Кронштейн6 жыл бұрын
Гуглоперводчик наверное чудит) Хорошо хоть не с китайского переводили)))
@ПавелКолесников-ъ7е6 жыл бұрын
Смущенная - потому.что у него штаны постоянно сползают до бикини. :-)
Ich wünschte, ich könnte so schnell arbeiten, dann war mein Badezimmer fertig, hahaha
@wwsjr26 жыл бұрын
Where is the drain? Guess I missed it.
@migrationfuntimes3036 жыл бұрын
that will be any lowest point at the wall junction.lol
@Blankanik6 жыл бұрын
graham smith This is the point. If there is no drain, the floor can not be flat. It has to be up to 1cm (3/8 ") high by the walls, and lower in the center.
@sidstewart73994 жыл бұрын
Can someone tell me why not just fit timber joists, insulate between and then board. Quarter of the time
@charlesdefrancisco50566 жыл бұрын
What incredible talent....this craftsman is got a lot of talent and in my experience with this process he could teach many from his very professional job. If he is ever looking for a job ..I would hire him in a heartbeat..well done
@thiefkonto5 жыл бұрын
That's just wet mixed concrete, just like for foundation, takes about 1 week dry before ready to lay tiles. Nothing wrong with the way he did it. However I prefer half dry concrete mix to make bathrooms
@yuriu67086 жыл бұрын
Всё отлично но одно зачем он ложил сетку если она снизу стяжки а не в толще.
@ЦыкаВана6 жыл бұрын
Сетку правильнее класть вниз.
@AndresLemming6 жыл бұрын
Сеть не должна быть против пленки, для этой цели есть пластмассовые «туфли», которые увеличивают высоту сетки до 3 см, а от стены должны иметь зазор 2,5-3 см.
@СохибЕрназаров5 жыл бұрын
Правильно
@sergeygainullin57535 жыл бұрын
Да ещё и тонкую. МАК не больше тройки. Надо бы пятёрочку хотя бы, а ячейку можно и десять на десять под такой слой. Ну и ясно, что везде отступ нужен от края, от дна. Возле труб не надо
@МишаняСибиряк5 жыл бұрын
Зачем стока епкатся налил разгладить и всё делов, кусочек линолеума под угол мебели и всего делов то
@stewartmckay98304 жыл бұрын
If you want the job to go easier 4 to 1 mix course sand and cement dry but wet enough 2 ball in your hand level and trowel and wooden float
@pino_t04126 жыл бұрын
You need change job
@putusutama6 жыл бұрын
😋😀😁😂🤣😃😄😅😆😉😊
@oliverathos314 жыл бұрын
poverino , non perfetto
@michaelhermann99906 жыл бұрын
Estrich kenne ich erdfeucht, man gut das da noch Fliesen draufkommen- aber mit 10mm Zahnung den Kleber drauf, damit die Huckel überbrückt werden.
@rainergodel41446 жыл бұрын
Michael Hermann Das sehe ich genauso 😉
@bronchiosaurus27666 жыл бұрын
is das nicht fliesetrich der extra dünn ist um sich selbst zu nivellieren? die armierung scheint mir nur etwas tief, sonst alles richtig gemacht in meinen unfachmännischen augen.
@bronchiosaurus27666 жыл бұрын
ok vergiss was ich geschrieben hab, da fliest garnichts...
@MrKloetze6 жыл бұрын
Da muss schon min. eine 15mm kommen! Das der Kerl sich nicht schämt so nen scheiß zu veröffentlichten, jeder richtige Fliesen oder Estrichleger hätte Ihm was erzählt.
@stefanguido65466 жыл бұрын
Du hast recht. die nasse Pampe schwindet, da wird dir jeder Fliesenleger einen Rapport vom feinsten herauslassen. Die Ecken werden sich stellen, Risse auftreten.. Nacharbeiten kosten mehr, als der Estrich. Heimprojekt, mehr nicht.
@Randy_846 жыл бұрын
This is amazing! Great work!!
@jedruskmicic11675 жыл бұрын
spierdalaj
@cms-jf2sy3 жыл бұрын
Очень много воды в растворе, он сперва совсем воду лил , как наливной пол, такой состав даст усадку и треснет наверняка. Да и сетка не будет работать, толку с этой сетки ноль
@g.mendoza81386 жыл бұрын
I don't get the title?!
@kopernickos6 жыл бұрын
I'm from Poland and i have problem too
@farikomike5246 жыл бұрын
Nor me.....
@giterdun18646 жыл бұрын
5 inches of mud over suspended plywood for no reason.
@tekmusti6 жыл бұрын
i am turkish even i couldnt get it
@wartoxxxcc17016 жыл бұрын
The title is Hungarian but this worker is not sure :)
@pocr63022 жыл бұрын
Hello, can you please tell me the name of the leg support you are using at minute 3:00 and were can I buy it from.
@junglebunny56736 жыл бұрын
can someone explain what he did wrong. looks ok to me
@johnknoefler6 жыл бұрын
The process of screeding (leveling off by pulling a board across the wet concrete) was left a bit rough. It looks fairly level so it's ok for placing tiles. That's why there was no finish floating done. The few rough spots can be ground down with a diamond abrasive wheel so it's not big deal. In all fairness, it's a really awkward place to work. The lighting was crappy and you really need good light to see what you are doing. Plus, no one was there to help him. Also, he had poor tools to do the job. All in all, it's satisfactory considering what it's for. Basically, tiles are going on top of it so it's no big deal.
@junglebunny56736 жыл бұрын
i assumed he was going to tile it.
@evanpenny3486 жыл бұрын
Johnknoefler That's not really the point. Leveling a floor in this way is difficult and imprecise. Despite the initial use of a laser level it is not practical to achieve a good result by sort of winging the screeding in this way. Many years of practical floor tiling convince me that this is not an easy job in the best of circumstances, carpenters do not understand the tolerances needed, and a better system of perimeter boards to screed to are needed. Well done to the flooring guy for his job, but not overall a noteworthy system.
@johnknoefler6 жыл бұрын
Honestly, his screed technique was a bit clumsy but it will pass.
@anitatrent61026 жыл бұрын
johnknoefler I
@godbluffvdgg4 жыл бұрын
Poor guy, working by himself...THAT is a ton of stuff to do without another mechanic and at least one helper...Work smarter not harder...
@tootman0016 жыл бұрын
attention to detail is superb , I wish I had his patience job well done!
@pp-jh4ig6 жыл бұрын
watched 5 minutes trying to figure out what the title means until i realized its auto translated to Hungaryan
@hughpole42594 жыл бұрын
even googled it up... well... I'm dumb....
@maroukhamaroukha42596 жыл бұрын
يخدم خدمة متقونة علابالي نلقىى جزائريين هنا 😁😁
@abdulhamedazawi16375 жыл бұрын
maroukha maroukhaسلام كيفك أنا عراقي ممكن وإذا تحبين أي سؤال على أي عمل في الديكور
@azizraimes50394 жыл бұрын
هههه انا هنا
@mattmotta8596 жыл бұрын
how does that thing stay level when he keeps moving it
@spawn86415 жыл бұрын
Them pipes ever burst be a pig of job to get to them for repairs, that floor will have to come up again more labour = £££
@jaywilson91826 жыл бұрын
I do this kind of work professionally. I would have done it a little differently. But he did do a good job. There had to be a reason why he was raising the floor I am assuming the rest of the floor was getting raised as well
@pierpaolobarone47154 жыл бұрын
Mi mette l'ansia vedere questo video
@rosariozappavigna32634 жыл бұрын
Come fare delle cagate😂😂😂😂😂😂😂
@sisconcorpindustries97556 жыл бұрын
Excelente trabajo maestro me impresionó cuando empezó a usar el láser y cada detalle de su trabajo gracias.
@ChannelTigre6 жыл бұрын
Quando si vuole spendere poco.
@rosariozappavigna32634 жыл бұрын
Questo mi deve pagare a .e per vedere questo scempio.
@ШамуилГре6 жыл бұрын
Не жидковат, растворчик? Расслаивается, опять же... Сомнительно, как то.
@AlexunderCortes6 жыл бұрын
Я тебе даже больше скажу, это наливной пол походу, он уже под конец схватываться начал, пока он с ним возился🤣
@HdReviewItalia4 жыл бұрын
basta con questo cartongesso ... legno e cartongesso ovunque per risparmiare tempo
@allanpkr6 жыл бұрын
seems a good job except for mix -dont know why it has to be that perfect.its a bathroom????
@keithy3634 жыл бұрын
allanpkr because if someone comes to my house or works on anything of mine and has that it’ll fucking do attitude they soon get shown the door
@4G63addict5 жыл бұрын
All these negative comments like everyone is perfect. This dude is a extremely hard worker. Weather it's done correctly or not, give the guy some credit for making a living for his family.
@EvntlLPer6 жыл бұрын
Wer soll den denn bezahlen? max. 1/2 Tag arbeit wurde durch den typen in 1-2 verwandelt, jedes stück styropor nachmessen vorm schneiden? Randdämmstreifen mit Laser abschneiden anstatt hinterher ein mal mit'm Cutter längs zu gehen? WTF
@stefanguido65466 жыл бұрын
Vor allem wird der Randstreifen geklebt. Schallbrücken in dieser Größenordnung durch die Tackernadeln , gehen in einem Mehrfamilienhaus never ever.lol.
@michaelazzaro5256 жыл бұрын
EvntlLPer .
@Lysaner6 жыл бұрын
Voralm hat er den Randstreifen mit den laser angebracht und mus ihn den noch kürzen omg
@MrFendtfan1236 жыл бұрын
und zu guter letzt liegt das aks gitter viel zutief, das gehört ins obere drittel.
@estrichligagermanscreed26466 жыл бұрын
Ich habe mich köstlich amüsiert wie dieser Unwissender sich abgequält hat. Echt lustig. Der hat fast alles falsch gemacht was man wirklich falsch machen kann.
@carlossilva-ql3js6 жыл бұрын
Que merda é éssa fazer isso por cima da madeira ...
@ulisses9676 жыл бұрын
Fiquei pensando na mesma porra!!!! Padrão europeu é cheio de frescura prum simples contrapiso!!!!!
@wally71046 жыл бұрын
Não é frescura. Condições de isolamento térmico e sonoro são diferentes do Brasil.
@bigze386 жыл бұрын
Em países civilizados (mesmo sendo "socialistas") só pode construir se seguir os padrões técnicos.
@foulukun6 жыл бұрын
Sendo que o título do vídeo meio que fala sobre o trabalho não estar muito bem feito. kkk e o cara tá achando que está "fresco" de mais. padrãozinho Br esse
@MrHBSoftware6 жыл бұрын
aqui em portugal não se faz nada desta paneleirice...todo o chão é cimento ou se for um andar elevado é placa em betão armado ou viga pré esforçada...não há cá madeira no chão a não ser por cima do cimento a servir de pavimento. isto parece aquelas casa pré fabricadas na américa do norte, cheio de madeira placa de gesso e muita massa a tapar a miséria
@алексейнарматов5 жыл бұрын
Просто я в шоке как можно себе жизнь усложнять
@gabornovak14984 жыл бұрын
Bruder, so viele von dir wie möglich mit der Vorbereitung. Die Glätte der gezeichneten Oberfläche überzeugte nicht! Ich bin 50 Jahre alt und habe in einem deutschen Land mit dem Wissen gearbeitet, dass du beschissen gewesen wärst! Es war schwer, meinem deutschen Regisseur vertraute Worte zu entlocken, aber nach einem halben Jahr. Er sagte, ich arbeite präzise und vorbildlich! Das war vor dreißig Jahren! Ich bin ein ungarischer Maurer!
@MrKloetze6 жыл бұрын
Ein leicht feuchter Zementestrich z.B. mit Schnellbinder hätte bessere Dienste geleistet. So ein gematsche kann man sich ja nicht ansehen. Naja, trotzdem das Ergebnis zählt.
@Absturz19866 жыл бұрын
Klötze aus klötze oder was?
@Neuss19796 жыл бұрын
@Thor The Northern Deutsches Video, deutsche Kommentare. So ist das Leben... ;-)
@ADRIAN-zh4ti6 жыл бұрын
Internetidiom is spanish
@manuelamaya95536 жыл бұрын
P
@manuelamaya95536 жыл бұрын
@@Neuss1979 yo
@garydouglass95774 жыл бұрын
That's floor leveller not floor screed. Far too thick for leveller to be used.
@mati-mw4qi6 жыл бұрын
między siatką a folią jakiś dystans by przydał...
@romanjastrzebski25426 жыл бұрын
Wg. Polskiej Normy min. 1 cm. A jeżeli nie ma w ogóle otuliny, to siatka jest zbędnym wydatkiem.
@yekoJhgg6 жыл бұрын
To prawda. Ale na takie małe pomieszczenie to przejdzie.
@tomaszjan52366 жыл бұрын
A czy na drewniany strop nie powinna zostać wylana wylewka elastyczna z włókna . Przecież to popęka z czasem . Ja osobiście robię inaczej
@yekoJhgg6 жыл бұрын
@@tomaszjan5236 przecież jest styropian.
@andrzejkurowski15756 жыл бұрын
się.
@fantastictools4825 жыл бұрын
Hi hab da ein neues Werkzeug entwickelt .... schaut doch einfach mal ....kzbin.info/www/bejne/fqrEmJSIo86spcU
@gabrielgonzales81635 жыл бұрын
buenos videos construccion work#1
@waleedm88135 жыл бұрын
There is a thing called cement board. Waste of time and money.