Fluid Flow Simulation In 3D Circular Pipe | CFD Analysis of Pipe | Simulation || FCFD-0022

[@abuusman7727]

One of the best video in KZbin!!! For CFD simulation. Sir please make CFD simulation on Open Channel also.

[@FrontiersInCFD]

Thanks Will do

[@abuusman7727]

@@FrontiersInCFD sir currently I'm working in Open Channel CFD simulation can you please help me out to solve that problem!. It's my humble request sir..

[@FrontiersInCFD]

wa.me/message/AAWWIVF5QK7OP1 for more details

[@miradkhammirjalilov9547]

You are genius bro

[@AbhishekK-hn4gd]

Awesome analysis..

[@FrontiersInCFD]

Thanks

[@engineeringlecturesandexpe3091]

Thank you Sir great ❤

[@FrontiersInCFD]

Most welcome

[@hoidinhthi6051]

Great

[@ShayariWorld047]

nice

[@FrontiersInCFD]

Thanks

[@a.s.periyarselvam975]

Thank you so much for your wonderful teaching.

[@FrontiersInCFD]

Glad it was helpful!

[@sharifullah1124]

thanks sir G

[@mostafa_mahmoud2849]

i have this error when i try to intialize at 6:30 in video (Current data has not been saved, including solution data and any report files, animation files, etc. Do you want to discard the data and proceed with initialization?) ......... can you help me what to do ?

[@FrontiersInCFD]

Go to workbench window do the follow right click on setup-clear generated data - and reset.. Same way do for solution and result

[@affanahmedkhan7362]

Jazakallah khair

[@ArghyaDas180]

I have an issue, @5:12, here the red and blue arrow lines are shown but in my case , those are not showing

[@FrontiersInCFD]

Which version of ansys you are using

[@ArghyaDas180]

@@FrontiersInCFD 2020R1

[@FrontiersInCFD]

I think available in newer version or please check if you have specified inlet and outlet in mesh selection

[@ArghyaDas180]

@@FrontiersInCFD it worked sir , thank you for your support and guidance

[@saharshsinha6121]

Can you make a video of same thing in 2024 R1 version as they are very different and difficult to understand.

[@FrontiersInCFD]

Ok will update

[@mohamadjubran3010]

In the minute 5:08, how did you get to the next page?

[@FrontiersInCFD]

Click on solution in workbench window

[@akshatgaur2489]

what about moniters section in outline view...it is totaly different in 2024...all videos on youtube are old once and does not solve the required problem...please reply sir🙏🙏🙏🙏🙏🙏

[@FrontiersInCFD]

Share screenshot on [e-mail]

[@joey_joe8557]

Hi. Great video 👍. Could you please make the same simulation video with a crack in the pipe and its effects on the flow?

[@FrontiersInCFD]

Will do

[@heahamthabet763]

What is the regime of the fluid flow in your project?

[@FrontiersInCFD]

turbulent with given velocity

[@elifyapc5939]

thanks its very helpful and i have a question. How can we find where is the fully developed laminar flow?

[@FrontiersInCFD]

Check velocity contour and find reynolds number based on that

[@avijitsingh2724]

Sir, Can you give me Numerical analysis of Turbulent flow through a circular pipe with heat transfer project? It would be helpful

[@FrontiersInCFD]

Yes, sure

[@FrontiersInCFD]

Connect with me on [e-mail]

[@avijitsingh2724]

Thank you....Sir

[@AaronChristopher869]

Helpfull video but the mic quality is questionable

[@FrontiersInCFD]

Will make improvement

[@vominhong3896]

can you make a video of flow simulation in perforated pipe? thank you

[@FrontiersInCFD]

If possible can you share details of geometry for reference

[@ДаулетЖумат]

Can you explain why pathlines are unavailable in Solution?

[@FrontiersInCFD]

select path lines from result section you can visualize

[@dyyhhhuujhggy]

Thankz a lot

[@mdjobaedalamrijvy165]

after the solution is converged x-coord y-coord this type of writtings are not coming.

[@FrontiersInCFD]

Can you share image at [e-mail]

[@mdjobaedalamrijvy165]

@@FrontiersInCFD i have shared it via mail.

[@swarupsawargaonkar8330]

Sir getting error while initialization that " flow boundary zone found adjacent to solid zone"

[@FrontiersInCFD]

Define the solid and fluid zone properly

[@AliEjaz-h7i]

sir how to validate it ? numerically?

[@FrontiersInCFD]

Generate Charts in Post Processor observe the parameter for example velocity or pressure and compare with experimental values

[@AliEjaz-h7i]

@@FrontiersInCFD Find the theoretical expression of the linear pressure losses through a round cross section pipe as a function of viscosity, low rate, diameter and length. Compare with your numerical results...sir how to find it? can you guide me actually I am learning software and i did this simulation and professor told me that you should do this and show me

[@AliEjaz-h7i]

you guide me ?

[@AliEjaz-h7i]

@@FrontiersInCFD you guide me ?

[@FrontiersInCFD]

If you have setup at your lab keep fixed rate of flow then measure the velocity and pressure at section (1) and section (2) apply bernoullis equation you can get the parameter experimentally and do check the same with numerical simulation

[@creativeandcraftsofknowledge]

Which software bro

[@FrontiersInCFD]

Ansys Fluent

[@ferielghamraci8034]

Please I need the details in the part (configuration)

[@FrontiersInCFD]

Ok please connect on whatsapp

[@osmankksal71]

Can you send the shapes as PDF?

[@FrontiersInCFD]

Diddnt get?

[@osmankksal71]

We have homework, I like your work very much, I need to present it to the teacher

[@bforme8745]

While running result Application failed to connect

[@FrontiersInCFD]

Close solution window open only result window. If not clear generated data in result and try again

[@litubabu8348]

Sir journal plz

[@FrontiersInCFD]

Didnt get ! Which journal?

[@sheetalgoyal2399]

Helo sir muje cfd ki class laina hai

[@FrontiersInCFD]

Ok. are you loooking specific related to any project or just need basics of CFD

[@FrontiersInCFD]

Please connect on Whats app [phone]

[@SagarSaini-bm17]

PATH LINE NHI DEKHA RHA OPTION

[@FrontiersInCFD]

Clear generated data in result

[@cricketvlogs8830]

Bhai thoda ache se bta do mrko kl y project submit krna h plZ PATHLINE UNAVAILABLE DEKHA RHA H

[@SagarSaini-bm17]

@@FrontiersInCFD hmm plz sir?

[@SagarSaini-bm17]

@@FrontiersInCFD sir bhaut bhaut dhnywad ❤❤

[@pundleekm9117]

Slowly teach sir

[@FrontiersInCFD]

👍