Flywing FW450 GPS and ATTI settings

[@jerryzito6840]

Where do I find that software/ Thanks for the video.

[@CertsUAsPilot]

Can you lift off in ATTI mode and while airborne switch over to GPS?

[@charlescoby5741]

You going to make a flight, with the changes?

[@kx4gamingandmodels123]

I know this is old, but just came up on my feed. I’ve got my switches up GPS, middle ATT, and down 3d… I don’t really see the need for return to home, I never fly so far away that I lose perspective

[@Maltojo]

Thanks!! What exactly is ATTi mode, as compared to 3D or Normal or 6G? I hear about ATT in different places but I don't quite get it yet. :)

[@CRUZROYHelicopters]

its 1400us its between GPS and home mode, its stable without the gps , so it will stay level but drift

[@bradyates7046]

I have blinking yellow light on gps switch. as you say it indoors at this time . I need to see if it change to green outside today.if it work I will not upgrade the gps unit.

[@jeffkraus1457]

What is ATTI MODE? Also, please give me a down and dirty tutorial on binding my Flysky FS-i6s Radio from my 450 to the FlyWing BELL-206 Thanks

[@CRUZROYHelicopters]

you have to add models, that radio only has 5

[@CRUZROYHelicopters]

kzbin.info/www/bejne/pJyalnaIZZKCqqs

[@CRUZROYHelicopters]

once you follow the add model video, follow this one to make settings the same . kzbin.info/www/bejne/sKHOoWh9Yq6Nr6s

[@CRUZROYHelicopters]

atti mode, is heli will keep height but lose gps

[@RGCbaseace]

I did the factor reset now gps and atti have no difference like it did like yours i think mine is set now will try tomorrow

[@mariopires4391]

I did exactly as you explain in this Video Clip (3D-»ATTI=1400) so it was expected that my FW450 would actually maintain the Altitude BUT THAT IS NOT HAPPENING. If I don't control the "altitude" with the Colectivo, the Heli will fall to the ground. Can my Friend give me an explanation for this? Thank you very much for your attention. Mario

[@RGCbaseace]

Friend you and me both

[@RGCbaseace]

I think we got to change the pitch setting their is a difference when you switch between the two ?

[@RGCbaseace]

Been trying this on mine but atti seems just like 3d to me as mine will drop if not fast enough on the left stick she doesn't stay at any hight but is spot on in gps

[@CRUZROYHelicopters]

need a computer and a good outside calibration

[@RGCbaseace]

@CRUZROYHelicopters doing that right now lol. Seems to gain a bit of collective between gps and atti that normal ? It sure didn't climb last time between gps and atti gps is rock solid All looks good gonna try

[@RGCbaseace]

Ok tried it again in just gps all is still good but I think I damaged the belt last time it came down fast I switched back and gave it up it made a unhappy noise I suspect a few belt teeth are gone

[@alexlucyrep9948]

each time i put mine in atti mode it drops from the sky have to put more up on controller yes blinking red

[@danduer1174]

If it is dropping you are in 6G mode you have to go on the software and hit the factory reset button to completely reset the flight controller to get ATT mode especially if your H1 is the heli version but caution when you hit the factory reset make sure that you have either wrote down or took a screenshot of all your previous parameters and swash plate numbers before you hit that factory reset Hope that helps you

[@alexlucyrep9948]

@@danduer1174 thanks will do taken all photos and will reset it next week after fun fly week end xx

[@danduer1174]

And I also forgot to mention my friend when you go on the software it has to be version 2.0 software

[@alexlucyrep9948]

@@danduer1174 ok thanks again for reply will look what vir iv got doing it next week many thanks x just looked yes got vir 2.0

[@danduer1174]

Now when you get done setting to factory default settings in 2.0 and you get all your parameters and everything reset when you get done have it in 3D mode which is the blue light if the tail motor does not start when you unlock it then you have to go to version one 1.81 and restart the tail motor in that version I know it's crazy but I've been through all this that's how you have to do it if your tail motor starts in 3D mode then you're fine