THE USE OF THE EXTINGUISHANT PANEL,HOCHIKI,VES,AVENGER WITH KIDDIE CYLINDER
Пікірлер: 35
@bruce2544 ай бұрын
This is amazing...now i understood everything.Thanks big🙏
@amarjeetravidas64662 жыл бұрын
Excellent 👌
@Eshtechlinks-IT-SupportАй бұрын
i love your video
@ManjeshKumar-qy7zh7 ай бұрын
Sir you are good video make video it video is very helpful for us
@makofficialvlog2676 Жыл бұрын
Nice❤
@Dime_Bar Жыл бұрын
Very good video thanks 👍🏻👍🏻👍🏻
@michelmambueni42892 жыл бұрын
Les explications sont claires malgré vous ne parlez pas français, étant expert.je comprend parfaitement...
@engineersguide42492 жыл бұрын
BON À ENTENDRE ET MERCI POUR LE COMPLÉMENT
@engineersguide42492 жыл бұрын
VA FAIRE DES SOUS-TITRES FRANÇAIS QUAND IL Y A PLUS D'ABONNÉS FRANÇAIS LOL
@edwaynemago26339 ай бұрын
to reset the solenoid use the proper resetting tool and use the fm200 preventive maintenance checklist
@Matrickz8 ай бұрын
where is the link you said in the part of your video on how connect or wiring that panel can you please share with me
@yasararafath3184 Жыл бұрын
If i torn the manual side that time alarm activated time FM-200 will be released or not!! Can you tell me about please
@engineersguide4249 Жыл бұрын
if what you saying is activating the manual release then its yes it will release in zero secs
@gelovlog93614 ай бұрын
Its possible to remove the supply or signal from c. Panel to solenoid so no need to rmove solenoid valve thanks
@engineersguide42494 ай бұрын
it is possible but to check the activation of the solenoid wont be applicable, and you have to get another EOL to normalize the panel..
@RolandOrapa-dr6hl3 ай бұрын
what is the comnon trouble of this panel . sir gobless po
@samsumaila865410 ай бұрын
Please which spanner size can be used to remove the solenoid
@engineersguide42499 ай бұрын
solenoid is supposed to be hand tightened not with a spanner
@erickm67812 жыл бұрын
Hi plz How to do if I need training for automatic fire suppression system ?
@engineersguide42499 ай бұрын
you can message us directly
@twahashearer83023 ай бұрын
@@engineersguide4249please share your email, very helpful demonstration
@falcond2142 жыл бұрын
Can you share how you cleared the fire zone lights on the panel please?
@engineersguide42492 жыл бұрын
You need to reset it by pressing the processor reset button below the key enable switch ... Just give me a feed back after it's done ✅ TNx
@falcond2142 жыл бұрын
@@engineersguide4249 press reset when the alarm sound is working? Or first I clean the detector and then press reset?
@engineersguide42492 жыл бұрын
You can only reset when the system is not in discharged mode ..but if it discharges u need to hard reset by resetting through the pressing of processor reset
@engineersguide42492 жыл бұрын
@@falcond214 you can silent the system, clean it then do the reset to avoid continuous alarming
@samsumaila865410 ай бұрын
From the cylinder
@yathi262 Жыл бұрын
Where & how to connect Manifold Discharg Pressure Switch?
@engineersguide4249 Жыл бұрын
any where just above the union at the cylinder and for the panel side tell me the kind of panel you are using
@mdsahinalam95379 ай бұрын
Friends what's your company name ? Plz
@shafiqmughal11152 жыл бұрын
I need information abort switch said termintion
@engineersguide42492 жыл бұрын
NO WORRIES JUST TELL ME THE ISSUE AND WOULD BE GLAD TO HELP YOU OUT ..FOR THE TERMINATION ITS JUST CONNECTING IT TO NORMALLY OPEN WITH YOUR END OF LINE RESISTOR FIXED
@dadabhai58546 ай бұрын
😆😆😆😄😄 very easy this system
@azazulahmad869310 ай бұрын
How to connection with hvsc fan
@engineersguide424910 ай бұрын
It's always advisable to get a relay when u want to connect any fan or damper