Ford 9 Inch 8 Inch Rear End Bolt On Disc Brake Conversion Kits Tech Talk

[@sonofravok]

Thanks guys. I am installing this kit on a Speedway Motors Ford 9" today. So much better than the PDF instructions.

[@busdriver1209]

Thanks for the informative video! I wish I found it before installing my kit. I purchased the MBM Ford truck 9 inch version with the 5x5.5 bolt pattern. The included instructions are HORRIBLE! I've been customizing for many years and realize this is a custom part and there are different installations based on differing years of the same truck. Instructions covering every situation is not possible. However, thorough instructions or helpful hints would be nice. First the instructions said that the axle flanges needed to be 6 1/8 inch or smaller or else the axle flanges would need to be machined. As stated earlier, my kit was the Ford Truck 5x5.5 rotor pattern. If the axle flange was machined to 6 1/8 inch you would almost machine into the axle stud holes! My axles flanges were larger than 6 1/8 inches yet the rotors still fit fully onto the axles. This axle flange specification is probably specific to the smaller Chevy bolt patterns. It would be nice to know that there is a different specification based based on axle bolt pattern size. Next, quality control is somewhat lacking. The primary bracket had two holes that were slightly mis-drilled requiring me to enlarge them. One to make to make the primary bracket fit on the differential axle flange. The other to make the secondary bracket fit. This made it necessary to enlarge the holes on the lower rectangular spacers. I also had to I had to reshape the rectangular spacers to clear the differential housing flange.There were cylindrical spacers that the instructions didn't mention, but were necessary to get the caliper spacing correct. If you install one of these kits be prepared to customize, it's not just bolt on. The most frustrating part of the kit were the incorrectly drilled parts.

[@randyhancock7713]

Great video. Good detail, easy explanation

[@CHRISTOPHERIRION]

Awesome thanks 👍👍 GOOD CONTENT

[@johnbehneman1546]

Excellent video and excellent education. It looks like a great weekend project. Thanks for sharing!!! I learned a lot.

[@daleolson3506]

This only did 1/2 the job. Show how to adjust those things and bleed. That’s the candle on the cake

[@Liveinthedirt]

Can you guys show the install of the E brake cables

[@chewbaccadawookie4038]

great video

[@radioguy1620]

also if you paint the parts make sure the mating surfaces are bare or will possibly work loose.

[@lionelgriego1704]

Is there need for a new proportional valve 77 f150?

[@Herman-b4q]

Q with this kit do you have to update anything else like master cylinder?

[@luiscontreras4417]

This brake kit will work on a 9.75 ford fx4 rear differential ?????

[@luiscontreras4417]

The 9.75 is from a 2007 f150 want to swap to a 87 c10 wandering if this will fit or need a different kit ??????

[@MccormickAutos]

Kit for 1995 f150 5x5.5” lug size?

[@trevorstrauss9978]

5x5 kit?

[@neilvaughan4163]

What are you guys doing or using for parking brake cables for this style caliper. My original factory cables are two short and the universal cables seem to require some creative alterations to make them work?

[@michaelsummers4651]

Kit comes with new rear parking brake cables

[@2015_Rubicnn]

I had a custom set made for my 72 Camaro. I have a quick performance 9 inch with this same brake setup and no e brake cables included.

[@lucasthompson9257]

Opie from Sons of Anarchy got a haircut

[@bobhilly546312156332]

Is there a kit for 5x5.5 truck bolt pattern

[@speedwaymotors]

This should work for you: www.speedwaymotors.com/Speedway-9-in-Ford-Truck-Rear-End-Disc-Brake-Kit,296887.html

[@Mr-117]

also curious where you would get or what pads are used in this kit?

[@davidperrie8931]

Part # 9193381 GM Metric 1978-Up Soft Street Brake Pads

[@rickshults2697]

Will these work with 15" Jegs spike rims with a 4.5" backspacing?

[@speedwaymotors]

Those wheels should work with all 15" wheels, however we have never used those particular wheels.

[@stoneyswolf]

@@speedwaymotors Wait what? Lol

[@SAM-eg7jg]

First and foremost ...... Axle center-line to furthest outer point of the caliper..!!!!! I dont car about the installation or product until and only until i know if it will fit my wheel. why..? is this not the first thing mentioned..??

[@cornmac1796]

Does anyone make after market dust shields for a setup like this

[@speedwaymotors]

We do not offer any aftermarket dust shields for these brakes at this time.

[@mdsadin7097]

Anek valo mekanikal morors

[@larrysmith8898]

Where would you get your replacement break pads

[@tonypepperoni229]

i just bought a kit for my 8.8 that looks very similar to this I believe they are like G body or at least GM style calipers so id imagine once you have that knowledge pretty easy to source pads. Did you ever figure this out and then some? if so now help me haha

[@davidperrie8931]

Part # 9193381 GM Metric 1978-Up Soft Street Brake Pads

[@haydendeland8997]

This kit can be used on a 03 Ranger with a 8.8 rear axle correct?

[@speedwaymotors]

I'm sorry to say that no, this will not fit a Ford 8.8" rear axle. This will only fit an 8", or 9" axle which both share the same axle flange. You might take a look at something such as this for your 8.8" axle: www.speedwaymotors.com/Wilwood-140-3018-B-FDLI-Rear-Brake-Kit-Ford-8-8-w-2-5-Off-5-Lug,106038.html

[@MrElPoderozo1]

How can I purchase this? 😳 phone# part #? Thanks.

[@speedwaymotors]

Here is the link to our website to purchase this brake kit: www.speedwaymotors.com/Speedway-Ford-9-Inch-Rearend-Bolt-On-Rear-Disc-Brake-Kit,5336.html This link includes the e-brake caliper: www.speedwaymotors.com/Ford-9-Inch-Bolt-On-Rear-Disc-Brake-Kit-w-E-Brake-Caliper-,35268.html

[@MrElPoderozo1]

@@speedwaymotors Thank you👍🏽. I'll be calling in a few weeks when it's not so cold to work in the garage here in Wisconsin, thanks again. P.S. I notice that the kit with E-brake is on back order. Any idea how long are they going to be in back order?

[@factoryspeed6786]

Cars and trucks do not have an "emergency" brake. They have a PARKING brake. That is why there is a "P" not an "E". It is for parking.

[@Godsy_Garage]

Maysured

[@Mr-117]

lol right?

[@BrendanWorks]

Boy this sure makes me not want to buy your conversion kit. The part where I need to drill out brand new parts is crazy. That's why you buy a kit, so it's all done for you. With a very common setup like a Ford 9", no drilling should be necessary. That, and your video starts with the assumption of the least common scenario: building an axle setup from scratch. Most everybody *already has a car* they are starting from. That's why it's a conversion. Your video appears to be setup for the convenience of setting up a video, not to show a person how they'd actually do an install. I'm sorry to be so negative, but this is all way off the mark.

[@carloswilson3853]

Phone #

[@speedwaymotors]

Hello! Our phone number is 800.979.0122! We'd love to hear from you!