FORD EVEREST Boost pressure control valve vacuum solenoid replacement and MAP / MAF relearning

one of the causes why sometimes turbo is slow to respond. on this video also will show if you replace or clean map or maf much better you reteach o relearn it to the system. you can also show on this video regarding tpms, and throttle control. thank you. DIY. Endeavour Endevour Endavour Endeavor Endevor Endavor Ranger Mazda BT50

[@rommelrevilla3238]

Igud day sir gawa k video kng San nakikita ang pcv valve at air breather NG everest thnx

[@SonicBamLIM]

Nabasa ko sir WLC and WLT engines ng gen 1 to 3 wala pong PCV valve meaning open breather unless G6 series engines

[@reydseo7772]

Sir, yung smen P0093. Na repair na yung sa injector, seals, washers etc at rebalance/recalibrate. Wala po leakage. Bumabalik pa din yung check engine light pag tumatakbo yung sskyan. Same error code. Nag 2nd opinion kami, at pahingi po ako ng opinion nyo about dito. Ito po quotation 37k inclusive po 1 Fuel filter 2 Suction Valve 3 Re balance injector 4 Pressure pump reveal, Re allign 5 tune-up

[@SonicBamLIM]

Yung sa return hose po kaya sa injectors? Join us po para mas madami makapagshare facebook.com/groups/487127618450740/?ref=share Then try niyo din po dito pacheck facebook.com/everestmods/

[@reydseo7772]

@@SonicBamLIM Will do po. As much as I want to, nsa mindanao po kasi ako. Thank you.

[@SonicBamLIM]

@@reydseo7772 ah oks po bandang davao po ba?

[@reydseo7772]

@@SonicBamLIM Yes po Davao

[@SonicBamLIM]

@@reydseo7772 try niyo po dito facebook.com/ajraptors/ Balik din po ako davao soon

[@rpd5911]

Hi, I have Ford Everest 2011 model... automatic. 4*4 light remains on always..that too 4L ..I have checked the motor..it's not working. Where can I get it fixed ..

[@SonicBamLIM]

@@rpd5911 try 1st to clean the switch

[@rpd5911]

@@SonicBamLIM ok. Let me try n see. This issue came few days back and then went..then one day while I was driving at around 20m/hr , one of my friend turned the switch to 4L. Since then it is not coming to 2 wheel drive . When I turn the ignition on, it just goes and then reappears immediately. I also think there is some electrical issue .what are other possible reasons?

[@edmacu]

Sir Nestor, si Wood Ward po ito. Ito yung sinasabi nyong cleaning ng Vac solenoid?

[@SonicBamLIM]

Ah yes po sir sakop ung sa filter sir

[@edmacu]

@@SonicBamLIM Ayos. Thanks Sir Nestor

[@marv251]

Gud am sir. Kapapalit ng timing belt, dati po malakas humatak pero noong napalitanng belt parang hirap humatak sa uphill even na sa first gear..ano po kaya ang problema.. thanks po..

[@SonicBamLIM]

Maganda po madouble check baka nawala sa timing lalo na kung saktong after palit naramdaman

[@shankar6891]

I have the same endeavour in India it's 3.0 automatic diesel. I get black smoke when hard acclearation and low pickup. My mechanic says to clean the turbo. EGR. May I know your advise

[@SonicBamLIM]

Yes it is also possible correct along with the injectors.

[@shankar6891]

@@SonicBamLIM what is the main reason of black smoke. All of these or any one of these? Injectors looks good idling or missing complaint I don't have. Just a black smoke while hard acclearation.

[@SonicBamLIM]

@@shankar6891 one of those at a time. Check turbo first. How about sensors?

[@shankar6891]

@@SonicBamLIM no signs on dashboard.

[@shankar6891]

Also if there is an issue with sensor. It should appear on OBD right. Let me know which sensor could be faulty

[@muhamadarmando2202]

hello, want to ask why my car can only reach 2000 rpm when re-learning, is something broken, sir? even though I have changed the map,maf and solenoid turbo and egr sir.

[@SonicBamLIM]

The process is not complete try it again. Is the steering wheel straight? Is there no any electrical devices turned on?

[@muhamadarmando2202]

@@SonicBamLIM none of the devices turn on sir, my steering wheel is straight, the problem I am having now is that the car cannot go over 140 on flat roads and the rpm can only reach 2500-2600. I'm not looking for top speed, but I feel disturbed when accelerating from 80 to 100 with road routes that go up and down or uphill, the rpm increases when accelerating, it can only be at 2500-2600 sir, while when the car is stationary, it can reach 3400-3500 rpm tdci matic sir, did I raise the pressure too high, sir? can rotate using the L button, under the turbo solenoid. I have replaced the map sensor and maf sensor with brand new, thank you sir for the reply, and I often see your posts about the Ford Classic on Facebook. but because of the language barrier I don't understand maybe you can help with my problem, thank you greetings from ford everest indonesia

[@SonicBamLIM]

@@muhamadarmando2202 did you also try the relearning process through a computer software?

[@marvinlao-ang1206]

Good eve poh. Ask ko lang po kung normal ba na my lumalabas na hangin sa oil filler cap at my talsik na langis pero sa deep stick wala naman. TIA

[@SonicBamLIM]

Ah kapag inopen po while engine running alam ko po yes po wag lang talaga sobrang lakas

[@rickchannel5130]

Mapangpalang araw solid bam, tanong lang po kc everest ko2008 lumalabas puting usok sa timing cover at sa brether wala sa tambutso wala rin sa steak

[@SonicBamLIM]

Ung sa timing belt cover baka may tagas camshaft oil seal kaya nalabas dun yung galing sa engine? Sang breather po yan banda?

[@rickchannel5130]

Hinde po timing belt sa taas don po sa kinakargahan ng langis pagbinuksan kupo yonnabuga po usok na puti at medyo natalsik langis

[@SonicBamLIM]

@@rickchannel5130 hindi ko po kasi makita actual pero alam ko normal

[@salvadorfloresta2292]

Gud am ask lng po kun pedeng hinde ireset after palitan ang booster pcv vaccum dpat talaga sya ireset

[@SonicBamLIM]

Pwede naman pong hindi kahit tanggal battery lang for more than 15 mins. Pero mas oks marelearn.

[@dennyp7264]

I have replaced the turbo solenoid and when I try to accelerate it is fast but when my car turns off then I turn it on again, the acceleration is not fast enough. then I calibrated the turbo solenoid again, the acceleration is fast again but once I turn off the engine and turn it on again, the acceleration changes less fast. what is the cause? thanks

[@SonicBamLIM]

Did you use a original solenoid or just a replacement?

[@dennyp7264]

@@SonicBamLIM I used a oem solenoid brand bosch not original solenoid ford. Is there any difference between original or not?

[@SonicBamLIM]

@@dennyp7264 some of us encountered problems on the replacement ones amounting less than 1k each not like the original amounting around 5k

[@dennyp7264]

@@SonicBamLIM So, is this the effect of non-original solenoid?

[@SonicBamLIM]

@@dennyp7264 but on your case you buy the bosch brand which is okay. The replacement that i mention has no brand at all. You can join us so others can also share. facebook.com/groups/487127618450740/?ref=share

[@tyronedeleon9348]

Good eve, nagpalit po ako ng map sensor last april pero hindi po ako nag relearn, pwede ko pa din po ba gawin magrelearn kahit matagal na?

[@SonicBamLIM]

Yes po...

[@reymarmalenab4734]

Sir good pm po... Anong store po ang pinagbilhan nyo boost pressure control valve. At magkano po salamat and godbless you po

[@SonicBamLIM]

Sa online lang po yung replacement. Try niyo po muna palitan ng filter yung orig niyo. N95 mask po gamitin. Test niyo din po if nagana pa gamit kayo obd of wala pwede naman po while idle hugutin niyo hose dapat may vacuum pa siya kapag dinikit sa balat

[@zamboangadelnortebtr4113]

Sir Bam sorry to disturb you mawalang galang na po, yung vacuum solenoid po Sir dapat e match po doon sa nakakabit sa everest namin or no need na kasi iisa lang uri nito para sa 2008-2014. Salamat po Sir Bam.

[@SonicBamLIM]

Dapat sir same yung iba kasi iba ang port or iba yung nozzle

[@zamboangadelnortebtr4113]

@@SonicBamLIM Salamat po sir ipa match na lang namin Sir, Thank you po.

[@SonicBamLIM]

@@zamboangadelnortebtr4113 yes sir para sure pero tama naman gen2 to gen3 same baka lang ibang model ng solenoid maibigay

[@zamboangadelnortebtr4113]

@@SonicBamLIM Okay po Sir Bam, salamat sa palala.

[@albertisidro30]

Paano mo po malalaman na sira na po iyan at kelangan ng palitan?

[@SonicBamLIM]

Kapag medyo mahina na po ang arangkada at sa tingin niyo po napalitan at nagawa niyo na ung iba pwede niyo na po ito iconsider

[@albertisidro30]

Salamat po. Sa lazada po pla meron na niyan? I have the same model po kasi ng engine pero ford ranger trekker xlt 2009 model eversince kasi nd pa napapalitan.

[@SonicBamLIM]

@@albertisidro30 yes po meron pati shopee. Ah same nga po engine.

[@21.muhammadarmando18]

good evening Indonesian time, sir, sir, I want to ask my car after cleaning the intake manifold, sensor map, camshaft seal and supply pump seal, my car didn't have power until finally I replaced the turbo selenoid, and the complaint is still the same, my car can't go any further from 120 km/hour, previously my car could exceed 120km/hour, I've followed all of these steps and the same car can't accelerate above 120 km/hour, does if we replace the injector ring need to be re-coded sir? because I also had the chance to replace the injector ring, what I'm worried about is I'm afraid it will reverse, do I need to reset the ecu and injector coding so that my car can get good performance as before, sir? thank you sir for allowing to share

[@SonicBamLIM]

Did you try to scan even without check engine light? I am thinking possible map sensor is the cause. What kind of turbo solenoid did you use? Original or replacement? About the injectors, just remember the sequence. It also have guide code on the top. I think removing battery about more than 15 mins will also do.

[@21.muhammadarmando18]

@@SonicBamLIM I already scanned that the check engine didn't turn on anything, then I replaced it with the original sensor map, for the turbo selenoid I used the Bosch brand, I'm afraid my injectors were backwards. I've reset it by unplugging the battery for 15 minutes and the jumper to the cable is the same, the car doesn't have a problem, do I need to do a reset using a ford scanner, sir? to reset the ECU as default again, because many say resetting the ECU conventionally by removing the battery only manually is not possible so I was advised to restart the ECU with a scanner, does it have any effect, sir? I asked friends in Indonesia, they also said, try restarting the ECU with the scanner and recoding, according to you, does it have any effect? because I have been looking for the disease from the Ford Everest for 3 months, it has not been resolved, please advise, sir

[@SonicBamLIM]

@@21.muhammadarmando18 what do you mean injectors were backwards? Actually about reprogramming the ecu i really dont have any idea and here in the Philippines there no such that kind of troubleshooting. Or maybe instead of that try remap if the price is almost the same

[@21.muhammadarmando18]

@@SonicBamLIM sorry sir I mean the injectors are swapped so the ecu reads ridiculously because what I feel now is that if you put gas at 1000-1500 rpm the car vibrates even though before that it was all normal, thank you, sir, for helping, I hope you are always healthy

[@SonicBamLIM]

@@21.muhammadarmando18 how about the codes of each injectors and also the proper sequence located on the top plate of the engine when you remove the cover

[@rolandjaymarquez1798]

Good day ho. Need pa po ba i-relearn pag tinanggal to kahit nakaremap na ECU? Balak ko sana check filter. TY!

[@SonicBamLIM]

Alam ko po yes po. Kasi ubg relearn po talaga is para sa map at maf sensor. If nagpalit po or nilinis. Yung sa filter po ng solenoid laking bagay din po if mapalitan. N95 mask po then iparehas niyo na lang po kapal sa orig filter. Thanks.

[@rolandjaymarquez1798]

@@SonicBamLIM salamat sa info po. May physical shop ho ba kayo?

[@SonicBamLIM]

@@rolandjaymarquez1798 ai wala po. Hindi naman po ako mechanic. Just sharing lang po. Tnx.

[@PrincieSanchez]

sir ask ko lng biglang nag vibrate masyado yng engine ko and pag on ng ac hindi ntaas yung rpm

[@SonicBamLIM]

Check niyo po if may tagas sa injectors. Pacheck niyo na din po engine supoorts. Try niyo din wag mag diesel dun sa last station na kinargahan. Try din yung mas mataas na klase mg diesel. Yung sa aircon naman po hindi naman po talaga apektado rpm unless nababa naman po ba rpm after switch on aircon?

[@franktolon3479]

Wala ba pcv valve ang dord everest 2009model manual?

[@SonicBamLIM]

Alam ko po wala. Yung hose na nakikita is breather. Medyo confusing din.

[@roanpenaflorida361]

Sir paano mo malaman na sira na yan kac sa akin umiinit yung sa egr na vacuum solen oid valve

[@SonicBamLIM]

Mas oks mabasa po function sa obd. Tapos if madalas na siya paramg nagvivibrate ayun

[@restymiranda3152]

Sir ford Everest ko engine light same time na ko on lights or after few minutes okey, intermittent

[@SonicBamLIM]

Maganda po mascan

[@edwindayanan4317]

Sir, P2143 ang error code. Ano kaya ang dapat ko gawin o palitan? Ford Everest 2010 Automatic po.

[@SonicBamLIM]

Pacheck po EGR

[@gingerbread185]

lods yung relearning thru shorting ng obd2 port 1 sa chasis, applicable ba yan sa everest 2008 MT?

[@SonicBamLIM]

Yes po sir pwede akin 2008 din po

[@denniseugenio4415]

Good day sir paano malaman kung palitin na turbo solenoid?

[@SonicBamLIM]

Mas maganda sir nababasa sa obd sana para makita readings. 2 kase yan para sa turbo at egr.

[@gaganpgir]

Hello sir,How can I contact you...Iam from India.I have Ford Endeavour 4x4....I need your help Thankyou

[@SonicBamLIM]

I am also member on FEVCI. You can chat me. Thanks

[@supertobi1003]

Sir same lang po ba yung boost solenoid ? Or iba po yung pang turbo and iba po pang egr?

[@SonicBamLIM]

Same lang po sir

[@rbdml8774]

Boss tanong kolang ford everest 2007 check engine problem lumabas sa scan egr nung napalitan na omokey naman mga ilang days nag check engine uli pero hnd na mabasa ng scanner kung ano uli naging problem

[@SonicBamLIM]

Try ibang scanner sir. Natry din ba muna remove batt?

[@rbdml8774]

sinobukan ko nadn po manual reset sa battery kaso ganon pdn

[@josepaololontoc2769]

Sir pa off topic po alin gusto ko po sana maglagay ng throttle controller, alin po ba ung tinatangal para po alm ko ang type ng connection nya?

[@SonicBamLIM]

Yung sumunod po na sensor sa ilalim ng gas pedal. Ung sa taas nung parang spring.

[@SonicBamLIM]

Dun po sa video from 19:49 to 19:51 yung nahagip ng dulo na hawak na wire. Ung sensor na nakakabit sa grey na bakal

[@jeffmark5338]

Ilang kilometer na odo meter mu paps?!! Munghang ito rin cause ng eve ko dati malakas yung 3rd gear ngayon mahina na?!

[@SonicBamLIM]

Now po nasa 170k+ kms na. Try niyo po muna kahit palit filter then kung may obd reader mas oks para mabasa parameters

[@jeffmark5338]

Meron akong lufi x1 sir accurate po ba reading nya s turbo pagnaka idle nasa 0.6psi ,, pag paakyat minsan nsa 5-7psi 1,700-2000rpm

[@SonicBamLIM]

Mukhang same naman sir. Try mo din minsan ano peak niya

[@jeffmark5338]

Ano po normal peak ngturbo sir if naka idle lang? Salamat

[@SonicBamLIM]

@@jeffmark5338 alam ko po zero then kaya minsan nagkakavalue sa idle hindi siya boost vacuum po siya

[@wjrnautosparepartstradingt9348]

Boss tanong kulang may Everest ako pero cranking Lang Walang andar

[@SonicBamLIM]

Namatay po ba dati while running? Nacheck niyo po timing belt? Orig key po ba?

[@wjrnautosparepartstradingt9348]

Dati tumak bo cya mamamatay tapos andar ulit ngayon Wala na hangang cranking Lang Hindi naman potul Yung t belt

[@SonicBamLIM]

@@wjrnautosparepartstradingt9348 fuel filter po? Natry po ba iscan?

[@jeffersonheinrichlopez112]

Goodpm po, Ser 2nd Gen Ford Everest 2007 model or 2008 natry nyo na po ba ang low power 3500 rpm only pero no check engine? Pero nalinisan na ang egr, intake manifold at throttle body bago din po ang MAF and MAP Sensor pero low power padin

[@SonicBamLIM]

@@jeffersonheinrichlopez112 if idle po sa matic normal po till 3500 lang talaga sagad na rpm sir

[@jeffersonheinrichlopez112]

Kasi noon po is abot nman po sya ng 5000 gang sa Red. At hindi po sya low power lalo na sa akyatan ngayon po is halos hindi na makaakyat at nahihirapan parang nawawalan sya ng hangin lalo na sa akyatan

[@jeffersonheinrichlopez112]

kzbin.infoQP8xBLaiHGs?si=nPy8Q9eeV7l7MMN8

[@SonicBamLIM]

@@jeffersonheinrichlopez112 manual tranny po ba?

[@jeffersonheinrichlopez112]

@@SonicBamLIM Matic po ser

[@sammymag-asin4015]

Lods ano kaya problema ng everest 2008 model pinalitan na ng map sensor..ganun pa rin P2227 code

[@SonicBamLIM]

Sinubukan niyo po ireset after? Tanggal batt na matagal po?

[@sammymag-asin4015]

@@SonicBamLIM ganun pa rin lods..pero may panibagong code since napalitan na min ang map..P2143 egr vent solenoid baka Yun ang problema kaya parati naka stored yung P2227 at P0106

[@SonicBamLIM]

@@sammymag-asin4015 ah baka mga po maganda maopen niyo din sa iba para makapagshare din sila

[@zamboangadelnortebtr4113]

Sir 2009 model AT below 40 po nag OD sya pero above 40 KM per H okay na okay po ang takbo nya, ano po kaya ang problema nito? Maraming salamat in advance

[@SonicBamLIM]

Blinking po yung OD?

[@zamboangadelnortebtr4113]

@@SonicBamLIM opo Sir

[@zamboangadelnortebtr4113]

Ay sorry sir, di pala nag be blink basta na lang mag reflect at tila hinihingal ang makina

[@SonicBamLIM]

@@zamboangadelnortebtr4113 natry niyo na po ipascan? Kelan po last palit ng atf?

[@zamboangadelnortebtr4113]

@@SonicBamLIM na scan na Sir, then bago lang napalitan ng filter, tsaka sabi ng nagrepair baka kailngan palitan ng ATF oil daw na para sa Ford Everest hinihintay pa namin. matagal na rin problema ito Sir.

[@supertobi1003]

Yung saken sir ford 2009 model low power po sya ano po kaya prob nung saken kakabili ko lang din po kase sir

[@SonicBamLIM]

Oks naman po pms? Fuel filter? Intercooler? Air filter? Cleaning po map sensor?

[@jeffersonheinrichlopez112]

Helo po Ser, @SonicBamLIM ... Ask ko lang din po sana kasi dalawa po ung solenoid Valve isa sa EGR at isa sa Turbo same ln din po ba sila ng solenoid valve at pwede po ba ako magorder ng dalawa na same parts sa shopee na namention po ninyo????

[@SonicBamLIM]

@@jeffersonheinrichlopez112 yes po same lang pero mas oks orig npo bilhin nyo. Natry nyo npo ba muna palit filter?

[@jeffersonheinrichlopez112]

@@SonicBamLIM hindi pa po. Siguro bili nln po ako bago mas better po siguro. Salamat po sa Info po na binigay nyo

[@jeffersonheinrichlopez112]

By the way po pala ser ung nabili nyo po ba sa shopee is tumagal nman po ?

[@SonicBamLIM]

@@jeffersonheinrichlopez112 medyo po pero mas oks siya sa turbo side. May mga naka encounter din na sasaglit lang

[@SonicBamLIM]

@@jeffersonheinrichlopez112 maganda macheck din reading sa obd para sure if ever itabi niyo pa din po ung orig

[@daraangkor3402]

Pwedeng palagay ang link kung Saan nabibili ang solenoid valve sensor?

[@SonicBamLIM]

Ito po s.lazada.com.ph/s.W8Ncm At shopee.ph/product/302189971/3166119401?smtt=0.278284462-1631006115.9 Pero try niyo din po muna palitan filter nung original kasi may mga naencounter din po hindi nagtagal ung mumurahin online

[@zamboangadelnortebtr4113]

Good morning po Sir Bam, ask lang sana ako saan makabili ng original na Mercon V at ilang letro po ang dapat kung bilhin. Sir about solenoid, iisang solenoid lang po ba ang para sa 2008-2014 o may specific na number na dapat muna makuha bago ako bibili at saan din po ako makabibili ng original nito, kasi may mga nakikita ako sa lazada. Salamat po uli, Sir Bam

[@SonicBamLIM]

Pangit po kasi ung solenoid sa lazada eh. Try niyo po kay everest garage meron siya nung half the price nung orig. Orig kasi masa 6k ata. Sa merconv naman po kay frdmaz sir roger. If drop pan process nasa 4 to 5 liters then palit filter.

[@zamboangadelnortebtr4113]

@@SonicBamLIM Sir salamat sa suggestion nyo, baka pwede makahingi ng link ng everest garage at kay Sir frdmaz Sir Roger, nasa Roxas, Zamboanga del norte po kami, tila malayo sa Maynila. Muli maraming salamat Sir Bam.

[@zamboangadelnortebtr4113]

Ah okay Sir meron na ako link sa Everest Garage, try po namin, Thanks

[@lucasdilin7520]

apakah bisa diterapkan di mobil ranger 3.0l tdci

[@SonicBamLIM]

Saya pikir ya. Silakan periksa item aktual pertama yang dipasang sebelum membeli dan mengganti sehingga Anda memiliki referensi

[@rolandoacosta7717]

Bro saan b Ako makakakuha Ng comp box nasunog Kasi ford everest 2008 at magkano help nmn

[@SonicBamLIM]

Join us po at may trusted po kami dyan facebook.com/groups/487127618450740/?ref=share

[@angelobito-onas4899]

Hi po sir ask ko lng po ung sa ford everest ko po hangang 1700 lng rpm nya pag lumagpas sa 1700rpm nanginginig na makina ayaw lumagpas ng 2000rpm po.dami na pinalitan na sensors ganun pa din po.pati mga hose ok nmn po.salamat po sa matulungan nyo po ako godbless po.

[@SonicBamLIM]

Wala po ba CEL? Map sensor po ba isa sa pinalitan? San po kayo nabili sensors?

[@angelobito-onas4899]

@@SonicBamLIM opo sir map sensor po pinalitan.sa car crew k po dinala ung sasakyan sila na rin po nagpalit.

[@SonicBamLIM]

@@angelobito-onas4899 pascan niyo po ulit kahit walang error baka makita

[@angelobito-onas4899]

@@SonicBamLIM ok po sir salamat po godbless.

[@SonicBamLIM]

@@angelobito-onas4899 likewise po

[@zamboangadelnortebtr4113]

Sir Bam Good morning uli, trans solenoid 32K-ORIG, 25K -US, AFT Mercon V-350/ltr at AFT filter P2,500.00. Bayad muna bago delivery. We assume na doon po sa sinabi ninyo na 6K ang Orig ay di kasama ang kaha ng solenoid at ang 32K ay buong set. Iyan po bang trans solenoid ang tinutukoy ninyo Sir? We have the assurance ne legit po itong bilihan na nericommend ninyo kasi almost 40K din kasi ang ipapadala namin. Muli maraming salamat sa mga reply ninyo.

[@SonicBamLIM]

Vacuum solenoid yun sinasabi ko sir.

[@SonicBamLIM]

Kanino po kayo natuloy transact? Kaso dko makita if same nga yung nacontact niyo baka ibang acct?

[@zamboangadelnortebtr4113]

@@SonicBamLIM I see Sir Bam, di pala dapat palitan ang Trans solenoid kaya vacuum solenoid pala dapat namin bilhin, salamat po sa paalaala Sir

[@zamboangadelnortebtr4113]

Sir Bam, Sandro ang pangalan at sa FRD kami nag transact sa bandang Banaue, Pasig po.

[@SonicBamLIM]

@@zamboangadelnortebtr4113 naku dko po kilala yan sir frdmaz banawe at sir roger kilala. Join po kayo sa fb page namin para mas malaman facebook.com/groups/487127618450740/?ref=share

[@sonnycaoyong9972]

Boss,ano Po kaya sira Ng ford everest ko,di CIA umaabot Ng 3.5 rpm,tapos wlang hatak Wala Rin check engine,ano kaya possible na sira boss

[@SonicBamLIM]

Kapag sa idle po ba yang 3.5rpm?

[@francisalarcon2848]

Same issue sana po masagot pag naka idle po at inapakan ang gas pedal gang 3.5 rpm lang po bago linis po intake at egr thanks po

[@nonatoinfante5077]

@@francisalarcon2848 yung akin bago mga pinagawa ko (2007 model), hanggang 2k rpm lang as in hanggang 90 kph lang tinatakbo. Nalinis na egr at intake nun. Kalaunan ay tumitigil namamatay engine while cruising SLEX. Buti na lang at naitatabi ko pa pahirapan. Dinala ko sa trusted shop, pinalitan nila ulit fuel filter at yung SCV suction control valve. Ipinalinis ko din turbo kasi 16 years na car ko di pa sya nalilinis. After that ay okay na takbo nya, di na namatay at nakakaakyat na sa mga steep inclines.

[@charlievillareal4617]

Hi Sir, tanong ko lang, pwede ba sa ranger trekker 2008 model yung murang scanner na elm 327 mini gamit torque app? low power po kasi tapos ayaw umakyat ng rpm hanggang 2500 rpm lang. nag try ako mag linis ng map sensor sobrang dumi na po. pero ganun pa rin ayaw umakyat ng rpm need po ba matanggal or reset ng check engine para malaman if sira na yung map? and kung nka check engine po ba talagang di tataas ang rpm? Thank you Sir

[@SonicBamLIM]

Tingin ko po same lang. Tama po mas maganda maread muna cel light. Kung error eh map sensor pa din possible palitin na

[@charlievillareal4617]

@@SonicBamLIM Maraming maraming salamat po sir sa reply. intay ko na lang yung order ko na scanner. God bless Sir.

[@SonicBamLIM]

@@charlievillareal4617 likewise po

[@arielgonzales8941]

Good day sir, ano number ng port tinutusok yung wire para sa relearning, may picture po ba kayo para sir, gusto ko din po itry ito salamat po

[@SonicBamLIM]

Pinaka first po sa lower right

[@josergevasquez3767]

Ask lang hnd ko ma gets ung sinasabi nyo relearning

[@SonicBamLIM]

Para po malaman na kagad ni system yung sa map at maf po

[@rojhomelbocobo2652]

pwede ba sir sa 4x2 to? tinry ko gawin yung re learning sir nag check engine sya and tinuro bigla yung map censor buo naman sya before gawin thanks sir

[@SonicBamLIM]

Yes po 4x2 po akin. Tama po ba yung naitap niyo? Minsan din po kasi after linis ng map sensor nasisira na din.

[@rojhomelbocobo2652]

@@SonicBamLIM yung nga po sir kakalinis lang lahat egr intake then nung nagtap nako nag checkengine na sir and need ba sir mainit talaga sya? naghihintay lang ako sir ng bagong map censor mag tap nako ulit baka kasi masira ulit yung mapcensor. First pin sir yung nasa video nyo mismo sir ginawa ko

[@SonicBamLIM]

@@rojhomelbocobo2652 yes po need normal temp. Opo pinaka lowest right pin

[@rojhomelbocobo2652]

@@SonicBamLIM thankyou sir ill try agad pag dumating na parts thanks sir

[@SonicBamLIM]

@@rojhomelbocobo2652 ung iba din po hindi nakukuha sa ilang try eh sabi din dun sa pinaka procedure

[@jrvillarin6911]

200 plus lng sir ano link sir

[@SonicBamLIM]

@@jrvillarin6911 mas oks orig na sir minsan hindi natagal ung mumurahin lalo na kung sa egr side lalagay

[@ryalvarez410]

bossing tanong ko lang po bkt ayaw tumaas ng rpm pag nakapark everest 2007 po salamat po sa sagot

[@SonicBamLIM]

Matic po ba? If yes til 3500rpm lang po talaga siya sa idle.

[@ryalvarez410]

2k rpm lang po boss

[@SonicBamLIM]

Limp mode po yan. Oks na po ba?

[@aligopen5902]

Sir parehas din yan sa 08 Ford ranger gamit ko pinalitan ko din binili sa shopee nagpalit na din ako ng MAP/MAF, camshaft at crankshaft sensors, bago fuel pump at battery. Pinalinis ko din ung Intake at EGR bago din ung sensor nya kaya lang problema ko hard starting at pagnagstart na biglang namamaty hindi tuloytuloy ung andar nya anu kaya problema dun sir? Tnx

[@SonicBamLIM]

Baka po need na calibrate injectors and injection pump. Try niyo din po pascan if ever kahit walang cel.

[@SonicBamLIM]

Take note din po dun sa mga murang online parts minsa po kahit bago pa sila bumibigay na din kagad

[@aligopen5902]

Sonic Bam LIM nacalibrate na din po ung injectors ko paano po itest ung vacuum valve solenoid kung gana pa o hindi sir? Tnx

[@SonicBamLIM]

@@aligopen5902 sa obd scanner din sir tapos download ka ng torque app. Para kahit running kayang basahin.

[@aligopen5902]

Good pm sir tanong po kasi pinalitan ng transparent fuel hose sa fuel pump pero may mga bubbles na dumadaloy papunta sa makina kasi mahirap magstart at pagnagstart napapatay agad. Ilang buwan lang po nagamit ung fuel pump na binili ko ano pa po magandang gawin sir?

[@jrvillarin6911]

Sir ano po link sa shoppe nyan

[@marv251]

Model po ng Ford everest 2007

[@SonicBamLIM]

Yes po same lang gen2 07 to 09. 08 po itong akin.

[@marvinoribello3467]

Hi sir, ano kaya problem ng everest ko. Gen 3. Hard starting kasi nagpalit ako map sensor bosch kasi may check engine. Nawala check engine kasi na clear gamit obd. Kaya lang after mga ilang weeks nag hard starting naman. Thanks sir!

[@SonicBamLIM]

Natry niyo na po irelearn? Kelan po last palit fuel filter? Tuwing cold start lang po ba?

[@marvinoribello3467]

@@SonicBamLIM yes mga month ago lang palit fuel filter. Yun lang diko pa ni relearn. Kailangan ba taLaga i relearn pag nag palit map sensor?

[@marvinoribello3467]

@@SonicBamLIM actually mas mahirap sya start pag umandar na makina tapos pinatay di sya basta ma start. Wala naman sya check engine.

[@SonicBamLIM]

@@marvinoribello3467 mas oks sir or pwede naman tanggal batt for 15 mins

[@marvinoribello3467]

@@SonicBamLIM na try ko n din tanggal battery pero ganun pa din.

[@arminperez1849]

Goodday sir tanong lng ford everest hngang 3500rpm lng ba tlga yan pag magaccelerate ka.ndi nb aabot ng 4or 5 yan???kc skin pag paahon walang hatak sir ndi nman nkacheck engine ano kaya problema sir

[@SonicBamLIM]

If matic sir at naka idle hanggang 3500 lang talaga. Pero kapag naandar na dapat mas tataas sa 3500.

[@arminperez1849]

@@SonicBamLIM matic sir pag andar ko then idle hngang 3500 lng

[@arminperez1849]

@@SonicBamLIM pag uphill sir walang hatak sir

[@SonicBamLIM]

@@arminperez1849 idle 3500 lang talaga max ng matic sir pero kapag nasa drive na mas mataas na.

[@SonicBamLIM]

@@arminperez1849 sa hatak oks naman pms mo sir? Updated? Meaning kahit diinan mo pa hindi na nagreresponse o react makina?

[@johnmarkcastillo1947]

Sir pano po malaman kung sira na ang vacuum solenoid? Thanks

[@SonicBamLIM]

Mas maganda po may obd scanner para ung system po mismo ang maread

[@SonicBamLIM]

Kadalasan po low power if ever oks naman ang pms niyo po pwede niyo na din po ito iconsider

[@rctrucker8310]

Low power na walang code sakin pinalitan ko lang filter ng solenoid..ayos n ulit

[@emmanoto7949]

Sir san banda bato sa everest 2006 di mahanap e

[@SonicBamLIM]

Ah sa gen1 po wala niyan. Meron medyo hawig iba po itsura nasa may malapit sa valve cover nasa gilid po

[@emmanoto7949]

@@SonicBamLIM yun kasi problema ko na wala hatak sir

[@SonicBamLIM]

@@emmanoto7949 oks naman po ang pms?

[@johnjeffnavarro]

Paps saan makabili ng ganyan throttle controller?

[@SonicBamLIM]

Dito po facebook.com/aileenfren/

[@jovieflor2020]

Sir anong symptoms para malamang sira po ito?

[@SonicBamLIM]

Kadalasan po low power lalo na kung ok naman na lahat ng pms. Nareread din po sa obd kung ayos pa.

[@shane881211]

Is the relearning applicable for bt50 2008?

[@SonicBamLIM]

Yes i think so

[@GerryMetrillo]

Meron ba AC idle up yung gen 3 bro?

[@SonicBamLIM]

Alam ko meron sir pero ung pagautomatic kasi ng compressor bukod sa matagal hindi din ramdam lalo na kapag running. Kaya ung iba nagpapalit din mechanical thermostat

[@GerryMetrillo]

@@SonicBamLIM ah ok bro, kc itong akin pg binuksan ku AC di ng idle up

[@SonicBamLIM]

@@GerryMetrillo oks lang po un basta wag bababa ang rpm

[@GerryMetrillo]

@@SonicBamLIM ok nmn bro, di nmn bumababa rpm, parang wlang ngyari

[@SonicBamLIM]

@@GerryMetrillo ung iba sir ginagawa lalagay maliit na bulb sa compressor para nalalaman kung nagautomatic

[@roderickvelasquez611]

Paps pa share naman po ng link saan kayo nag order, thanks

[@SonicBamLIM]

s.lazada.com.ph/s.dODWD

[@jonalynviluan9556]

Madaling paabdarin sir pag nakachoke

[@SonicBamLIM]

@@jonalynviluan9556 po?

[@animeside7333]

Sir saan ka po nakabili ng throttle controller

[@SonicBamLIM]

Dito po facebook.com/aileenfren/ Look for sir cha

[@CW-le2lz]

hm throttle controller sir?

[@KATSAMBA0719]

Pano po magrelearn ng mga solenoid na yn Sir?

[@SonicBamLIM]

Actually sir ung relearn para sa map at maf kung naglinis or nagpalit.

[@KATSAMBA0719]

@@SonicBamLIM opo Sir.halimbawa ngpalit po ako..Paano po mgreleaen Sir

[@SonicBamLIM]

@@KATSAMBA0719 same lang nung sa video sir. Sa pinaka lower right tap then ground 5x. Pwede din naman tanggal batt for 15 mins pero mas oks itong relearn.

[@KATSAMBA0719]

@@SonicBamLIM ok po Sir.salamat po

[@SonicBamLIM]

@@KATSAMBA0719 likewise po

[@GerryMetrillo]

Bro pano e relearn yung gen 3 2010 model 4x4 matic 3.0 engine? Na try ku kc yung ginawa mu pero walang reaction sakin. Salamat bro

[@SonicBamLIM]

Alam ko sir same lang minsan talaga ayaw gumana. Derecho ba gulong nung ginawa? Patay mga accesories?

[@GerryMetrillo]

@@SonicBamLIM yes bro, tinest kurin continuity ng wire ku ok naman, 3 beses ku na try wla din

[@SonicBamLIM]

@@GerryMetrillo kahit umilaw glowplug wala sir? Ung iba kasi ganun pero hindi din makupleto cycle

[@GerryMetrillo]

@@SonicBamLIM di umiilaw glow plug indicator sa dashboard bro, totally wala talaga reaction

[@SonicBamLIM]

@@GerryMetrillo natry mo na reader sa obd sir?

[@PanjiWidiatmoko]

Bisa dijelaskan langkah re learning maf/map sensornya?

[@SonicBamLIM]

Suhu pertama harus dalam kisaran normal. Roda kemudi lurus. Platform parkir datar atau rata. Semua electircal harus dimatikan seperti radio, lampu, pengisi daya. Dapatkan kabel dan letakkan ujung lainnya di port kanan bawah dan picu ground 5x di ujung lainnya. Jika berhasil busi menyala maka tunggu 2 siklus sehingga rpm akan naik dengan interval 10 detik. Terakhir, busi pijar akan berkedip 5 kali dan menyatakan sudah selesai.

[@erniequibod9363]

Idol anong esue ng makina pag sira yan

[@SonicBamLIM]

@@erniequibod9363 low power

[@dennisarago7592]

Boss San area ka? Patulong naman ako..try ko gawin din ung sa akin sana

[@SonicBamLIM]

Batangas sir pero nasa Davao ako now eh

[@johnmarkcastillo1947]

San kayo sa batangas sir tanauan lang ako

[@SonicBamLIM]

@@johnmarkcastillo1947 tanauan din po. Banjo west. Mostly low power po pero dapat unahin muna mga basic pms na matapos.

[@johnmarkcastillo1947]

Mgkapitbahay lang pla tyo sir darasa ako yun kasi problema everest ko low power

[@SonicBamLIM]

@@johnmarkcastillo1947 fuel filter napalitan na po? Map at maf napalinis na po saka intercooler? Air filter oks pa po?

[@teddyantonio5277]

Sir interchangeable po ba yang egr at sa turbo?

[@SonicBamLIM]

Yes sir common naman po basta ung linya na partners hindi magkapalit at magkabaliktad

[@teddyantonio5277]

@@SonicBamLIM pwede po bang linisan na muna? Kaya i DIY?

[@SonicBamLIM]

@@teddyantonio5277 pwede po palit filter

[@michaelbanguis6784]

@@SonicBamLIM saan po kaya nakakabili ng filter ng solenoid? Thanks

[@SonicBamLIM]

@@michaelbanguis6784 pwede po palitan n95 mask. Icompare niyo na lang po yung kapal.

[@MagalaTV]

Sir tanong lang po. Ung rpm po ng ford everest 2011 ko hanggang 3,500 lang po ung batak nya. Ano po kaya pwede gawin? O malaman kung ano pwede cause niya. Salamat sir.

[@SonicBamLIM]

Sa idle po ba ito? Matic po ba? If yes parehas ganun po talaga pero kapag naka drive na napalo naman po lagpas 3500

[@KATSAMBA0719]

Baka matic

[@SonicBamLIM]

@@KATSAMBA0719 baka nga po sir. Hindi na nagreply pati eh.

[@arminperez1849]

@@SonicBamLIM sir gnun din po problema ko hngang 3500 rpm lng pag paangat ang daan mahina hatak sir.ano kya problema sir

[@SonicBamLIM]

@@arminperez1849 kahit moving na at nasa drive po?

[@kridemotovlogs4758]

D gumagana sakin. Haizz

[@SonicBamLIM]

Nakailang try na po kayo? Normal naman po temp? Patay po mga accesories at ilaw? Pantay po parking? Derecho gulong?

[@geoffreyibanez4178]

paps nagana naman din ito sa gen 3?

[@SonicBamLIM]

Yes po same lang gen2 at gen3. Sa gen1 po kakaiba.

[@geoffreyibanez4178]

@@SonicBamLIM 2 pcs need sir no? laki ba improvement since napalitan?

[@SonicBamLIM]

@@geoffreyibanez4178 yes sir 2 pcs. Isa sa turbo isa sa egr. Yes sir laki improvement.

[@SonicBamLIM]

@@geoffreyibanez4178 join us facebook.com/groups/487127618450740/?ref=share&exp=e8c2

[@geoffreyibanez4178]

@@SonicBamLIM yes sir member na din po dyan hehe. ordered na din 😁

[@PrincieSanchez]

sir ask ko lng biglang nag vibrate masyado yng engine ko and pag on ng ac hindi ntaas yung rpm

[@SonicBamLIM]

Check niyo po if may tagas sa injectors. Pacheck niyo na din po engine supoorts. Try niyo din wag mag diesel dun sa last station na kinargahan. Try din yung mas mataas na klase mg diesel. Yung sa aircon naman po hindi naman po talaga apektado rpm unless nababa naman po ba rpm after switch on aircon?

[@PrincieSanchez]

@@SonicBamLIM pag on ng ac same prin nman rpm...para saan po pla pag palit ng solenoid ? Pki accept po ako sa group...salamat

[@SonicBamLIM]

@@PrincieSanchez sa turbo po at egr. Pwede naman po try niyo din muna palit filter nung solenoid. Wait po natin admins dun sa page