Ford Falcon XR6 water pump, tensioner & belt replacement

  Рет қаралды 81,875

Andy Mechanic

Andy Mechanic

Күн бұрын

Пікірлер: 186
@datreecutterredshaw425
@datreecutterredshaw425 3 жыл бұрын
Thanks for the video only thing i did different was remove the thermo fans first and it made access a lot easier , just a tip though when undoing the bottom hose throw a little piece of cardboard across the alt and it will prevent any of the rusty water and muck getting into it
@lk8300
@lk8300 2 жыл бұрын
The peanut dog that did mine just dumped all the water into the alt and I think the battery was still connected I said wtf are ye doing m8. He also left it leaking water from the pump seal after 2 or 3 goes at it. Few months later they sent someone else to repair his mess and they still charged me 900 I should've never paid my fault
@nixtone
@nixtone Жыл бұрын
One of the best. Great balance of clarity, explanation, regard to audience, personable without too much distracting prattle.
@AndyMechanic
@AndyMechanic Жыл бұрын
Thanks Nick. Have a great holiday. All the best. Andy
@nixtone
@nixtone Жыл бұрын
I've had an absolute nightmare getting this done on an 09 Territory. ATM I have new coolant pouring out from behind the water pump. There's a bolt-on fork like bracket to hold that steel rear pipe in place, I guess. Different bore to original so a little unintended reaming of new hole. I may have somehow mismounted it, but yours and other views just has that pipe sitting in the rear of the pump without any holders. Done all the new O-ring, rubber grease etc. Shit of a job getting pump mounting bolts back on. As others have pointed out, need to grind flanges away to enable room to reseat and tighten. And bottom bolt the champion of industrial design that seems aimed to prevent any sort of maintenance. No wonder this was the last Ford made in Oz. After 6 hours I was out in the rain,0at 10pm, dinner moulding on the table, mozzies and leaches feasting, massive comedy of errors. Expecting I'll have to go back over the coals to re-check pump is seated properly. More painful than starting yoga at 60! And this the short sanitised version...
@AndyMechanic
@AndyMechanic Жыл бұрын
Oh dear....well done for getting it done. I hate mozzies so would have likely given up & finished it the next day! Thanks for the feedback. All the best. Andy
@bobbushie4603
@bobbushie4603 7 ай бұрын
@@nixtone I have the same pump on a 04 BA falcon, the hole was blank, I just cut a thread into it
@troyvlody1365
@troyvlody1365 5 жыл бұрын
Takes 2 minutes to unbolt thermo fans
@glenntipping9216
@glenntipping9216 Жыл бұрын
Literally does
@sionetualau
@sionetualau 6 жыл бұрын
Andy.. I just wanted to say THANK YOU SO MUCH for making this video for Ford Falcon as no one has do a video about it.. thanks man.
@AndyMechanic
@AndyMechanic 6 жыл бұрын
No problem Sione, pleased to be of help. Cheers Andy
@bobbushie4603
@bobbushie4603 7 ай бұрын
About the best use for a mobile phone too, I have found myself using it for the same thing. It used to be the little pocket camera or mirror trying to see in those dark corners our heads won't fit but the things we can see with those little gems is amazing. Great job mate, I found winding the belt around the tensioner first is a bit easier. Themos are the first thing I remove , 2 minutes job done
@foxymoana
@foxymoana 2 ай бұрын
Ratchet spanners are your best friend with these engines
@wazowski6709
@wazowski6709 Жыл бұрын
Great video, although the number of times I found myself yelling "take the thermos" off was funny! It's literally 2 bolts & the wiring harness, makes life sooooo much easier.
@ziggassedup
@ziggassedup 8 жыл бұрын
I've seen that many times..The plastic P/Steer pulley too...Alternator probably got changed because of oil contamination from a leaking P/Steering high pressure line...Very common...Here's a tip for next time Andy....Pull the fans out of the way first..Two bolts and a plug...I leave the steer pump on..About 40 minute job start to finish but you did ok for a first timer.. some EF-AU used the clamp for the pipe and BA-BF(DVCT) have no clamp but lot's of the parts interchange...Interesting the cut out of the waterpump bolt...Never had to do that and I've done plenty of them and long bolts can go anywhere but the holes inline with the bore for obvious reasons...I like the practice you teach mate...If you ever need any info on Aussie Holdens or Fords just gimme a yell...Cheers..Oh and Ultra grey is my sealant of choice..Just a little is plenty...I'll give you a shout on a vid and see if we can get you some more viewers.
@denismckeen3476
@denismckeen3476 6 жыл бұрын
Think all ya need to know is Aus''Chevs -called Holdens (General Motors) and Oz Ford-both overpriced new/and for parts.. 'pieces' of 'Crap''-''God Bless U.S of A..the Southern Cross > and 'Dedicated Gas'' :)
@phugemawl
@phugemawl 9 ай бұрын
Yep, first thing to do is remove the fans AND there's no need to disturb the power steer pump or the alternator .... Crikey !
@rosswestley8547
@rosswestley8547 5 жыл бұрын
Have just spent hours replacing my water pump and after all the time cleaning the gasket off the block , fitting the water pump , and putting it all back together , my o-ring is leaking!! I now have to find time to do it all over again!! dammit!!!!!!! Thanks for your vids Andy
@AndyMechanic
@AndyMechanic 5 жыл бұрын
Bugger! Shit happens. Thanks for the feedback Cheers Andy
@tdlaustralia7791
@tdlaustralia7791 2 жыл бұрын
About to tackle this job unexpectedly so really appreciate this.
@ianwinn1161
@ianwinn1161 5 жыл бұрын
Thanks Andy. I just did a friends water pump and had a couple of concerns which were sorted after watching your vid.
@jamiejames4313
@jamiejames4313 3 жыл бұрын
It's 2021 and I followed every step all the way from nz thanks for your video brother chur..
@ultimatelifehack6899
@ultimatelifehack6899 5 жыл бұрын
Thank you sir, just did mine on a 2009 fg turbo, similar setup Only difference was the metal hose had a c clamp an bolt restricting it from coming off.
@cryptoozzy3866
@cryptoozzy3866 2 жыл бұрын
Did you tap a thread in water pump or just bolt and nut through it to attach clamp?
@robbievandewetering8636
@robbievandewetering8636 Жыл бұрын
Easy to understand and clear video ,lot better than most ,thanks
@davidsimmons3479
@davidsimmons3479 4 жыл бұрын
NICE VID ANDY watched a vid earlier on it was hopeless this vid was very clear and very well explained my wife who is 62 and me 75 we went the same way as you did except we did not remove the alternator just need that bit about the tensioner made it worth while watching will look for your vids in the future very well done Andy CHEERS
@mickyLat3652
@mickyLat3652 10 ай бұрын
2 bolts & an electrical connection & you could remove the fan & schroud which gives you a lot more room to move. Cheers
@DP-eb2yn
@DP-eb2yn 5 жыл бұрын
G'day Andy first off thanks for your knowledge , demos and humorous fun channel and a big hello and thumbs up to all the lovely tool girls.. now meanwhile back at the work shop.. I got an issue with my Barra xt falcon .. a lot would say there's ya problem already haha.. now we all know milky oil says head gasket but I've recently learned if there's no milky oil on the dip stick it could very well be condensation from sitting in winter whether and not driving far or a failed water pump ( is this true). Though the car doesn't over heat.. It does go through a lot of water but I can't see where it goes besides the little dry white water staining down below the water pump and a bit sprayed up on the bonnet lining. Now the water usage has been going on for a while I just thought the coolant bottle had a leak .. but just recently seen the milky oil under the oil cap and inside the top of the engine . And drives well though ive stopped driving since I found the milky oil. Would it be just the pump O ring and gasket or am I really in the shit here head wise. Thanks mate hope you can help Damien Vic Australia.
@DriftLifeAus
@DriftLifeAus 4 жыл бұрын
I've had a similar issue with my BF E gas. Leaking coolant. Thought head gasket as it had overheated once and milk in oil. There was a split hose, repaired that, put new thermostat, head gasket repair, new coolant, oil etc. Running fine. But still water leak. When at temp, water constant under water pump area. Hopefully resolves it all, and saves a new engine/head gasket.
@darrengow-brown171
@darrengow-brown171 5 жыл бұрын
Love your video even the part about the alternator bracket also your conclusion regarding the replacement of the water pump. Your camera shots are fantastic Thanks for making this very helpful instructional video.
@kereama0
@kereama0 6 жыл бұрын
Thank for this my AU did the same with the water pump pulley. So this is very helpful. Lucky I have AA+ membership and was able to have the car trucked home 200km. Will pull it apart tomorrow.
@AndyMechanic
@AndyMechanic 6 жыл бұрын
Good Luck. Pleased you found the video helpful. Cheers Andy
@johnny0628
@johnny0628 6 жыл бұрын
Thanks for the video Andy. This will help me change out my sons tensioner on his BF Ute.
@wazzazv614
@wazzazv614 7 жыл бұрын
Thanks, Andy this was a great video, I have had to replace the power steering module pipe and alternator, as one of the previous commentators did. The worse part was replacing the fan belt, I realized my four letter vocabular was vast yet limited.Your video helped a lot. An excellent video.
@AndyMechanic
@AndyMechanic 7 жыл бұрын
+Warren Fox Haha! Yes, I find profanity often eases the situation....off camera of course!
@EndoSurf
@EndoSurf 7 жыл бұрын
Warren, was the alternator easy to do from the top with the fans removed? Mine just went :S
@maoristutuff
@maoristutuff 6 жыл бұрын
Thank you very much this video saved me a whole lot of time checking part numbers and was easy to follow guide much appreciated.
@AndyMechanic
@AndyMechanic 6 жыл бұрын
Cheers :-) Andy
@dozer1zero676
@dozer1zero676 2 жыл бұрын
Thanks mate for your time and effort and good clear instructions l would not have replaced my water pump, With out your video, l sent a small donation for your help. Thanks mate and God bless
@AndyMechanic
@AndyMechanic 2 жыл бұрын
Cheers Matey, it's good to know the video was helpful & big Thank You for your donation, it is very much appreciated & will be put to good use on equipment or a future project All the best. Andy
@Beer_Dad1975
@Beer_Dad1975 6 жыл бұрын
10mm articulated ratcheting spanner is a must when working on the front of a Barra - either that or take the electric fans off. Plain water in the cooling system? Guessing this is owned by a young guy who doesn't really know much about cars. At least it's been replaced now. There is no timing belt on the Barra, it's a chain and will last a very, very long time provided normal maintenance is kept up. Seen taxis that have done 500,000km and the timing is still fine.
@UTPP
@UTPP 2 жыл бұрын
Great video mate, I'm half was through the job and using your instructional video every step of the way, cheers!
@user-sp5bn6ye8y
@user-sp5bn6ye8y 4 жыл бұрын
Pull the fans out first guys. Super simple to do and gives you loads more room
@AndyMechanic
@AndyMechanic 4 жыл бұрын
Yes, definately & very easy to do too :-)
@nicknicu1787
@nicknicu1787 8 жыл бұрын
Fantastic channel Andy! Good detailed videos and high quality camera work. Well done! Found your channel through Steve Rob's. Keep up the good work! Good luck!
@blondsuper1751
@blondsuper1751 8 жыл бұрын
Thank you for the video Andy; I did this about 18 months ago 4 friend, I didn't remove power steering or alt bracket, but I did remove the whole radiator with both fans attached to give me room- but now it's leaking again... I'm not looking forward to doing this crap again 👺
@ziggassedup
@ziggassedup 8 жыл бұрын
BTW I have to stop watching now because my wife wants me to stop yelling "Andy pull out the bloody fans.!!.".
@jcbfeather
@jcbfeather 7 жыл бұрын
lol doing the same
@PhilMeUpBaby
@PhilMeUpBaby 6 жыл бұрын
Watching with the fans in place. The pain is real.
@Djr67
@Djr67 6 жыл бұрын
Yes and how is it to remove the fans
@AndyMechanic
@AndyMechanic 6 жыл бұрын
Oh it's really easy. Just unplug them from the loom and if I remember correctly there are two bolts at the top of the cowl to remove & that's it!
@Djr67
@Djr67 6 жыл бұрын
yep thats it, I'm replacing the water pump in my brother 10/03 BA Falcon and I'm not sure if I have the right water pump, what model is the falcon you're working Andy? Apparently ford changed the water pump in late 2003 and I thought I bought the right one but I'm not sure
@garysanderson9121
@garysanderson9121 8 жыл бұрын
andy, a very well constructed how to video, and helped me greatly with my au
@AndyMechanic
@AndyMechanic 8 жыл бұрын
+Gary Sanderson Thanks for your feedback and I'm really chuffed to know the video helped you get the job done. It was quite a long, drawn out repair as I was initially told it was the cam belt! Which of course that engine doesn't have so I had no idea what to expect. I had to go to the vehicle twice and it's 100 km between my workshop and where the car was located so 400 km driving all up plus the time taken to do the repairs too! Happy customer and happy KZbinrs too....all's well that ends well :-)
@ronaldinolanda9832
@ronaldinolanda9832 5 жыл бұрын
thanks Andy it was very useful, keep up the good work.
@fnq-8890
@fnq-8890 7 жыл бұрын
This was a big help chum for working on my ute, cheers mate.
@AndyMechanic
@AndyMechanic 7 жыл бұрын
+Queenslander Hey, no problem, pleased it helped you get the job done. Cheers for the feedback. Andy
@philliptree1742
@philliptree1742 3 жыл бұрын
Geez thats a cracking video. Well done 👍👍👍
@magyaradam
@magyaradam Жыл бұрын
Does he need any gasket paste?
@denismckeen3476
@denismckeen3476 6 жыл бұрын
just passin thru-doin different job on Falcon 03 D.O.H.C - Good vid -Andy M..I probably would have done same way-Fans out etc..bit more room to swing /use Sockets/extensions etc..> bit easier way to do tensioner-(put Serpentine/Belt on over last'Pully's) ----- socket handle up=120'clock position--any pipe about 18inches long 'jus big enuff to go over handle--makes it ''Easier to swing''-and put belt on with left hand..03 Ford>has plastic scoop-down to air filter x2 P.K/Star screws hold easy undo-don't have to take off 'Plastic inlet pipe move forward> plenty of room to pull 'Bar/on tensioner--
@Brad_hj2tuff
@Brad_hj2tuff 5 жыл бұрын
No need to drop the alternator completely just take the bracket off at the front
@Koimith
@Koimith 7 жыл бұрын
Thank you for the tutorial, great work!! I am confident to replace the Idler pulley and tensioner now.. Cheers buddy =)
@AndyMechanic
@AndyMechanic 7 жыл бұрын
+Pete Smith no problem Pete, great to hear you found the video helpful. Cheers Andy
@baggs1955
@baggs1955 3 жыл бұрын
Usually a new idler pulley and tensioner leads to a failed water pump in the near future. I guess the extra tension from new tensioner causes the failure on old bump bearing.
@toddsonic
@toddsonic 7 жыл бұрын
Nice to see some parts are still made in Canada... :-)
@jockclayton1235
@jockclayton1235 4 жыл бұрын
One water pump bolt needs thread sealer on it !! 3 go into blind holes the other goes into the water passage and requires sealant , I personally use sealant on the new o ring as well . YES take the fan assembly out and you dont have to remove the alt or power steering pump , also you can buy a replacement pulley for the W/pump , but for the handy man its more convenient to replace the whole pump as shown
@cryptoozzy3866
@cryptoozzy3866 2 жыл бұрын
Do you mean loctite? Is it the longer screw that attaches to the bracket? They are a bitch to get to lol and I had to use bottle and nut for fixing bracket on back of water pump as didn’t have thread tapping gear but I forgot to loctite it,
@Acidassassin420
@Acidassassin420 Жыл бұрын
​@cryptoozzy3866 no jockclayton1235 is right there's a proper thread sealant that goes on the said bolt that enters the water passage
@cryptoozzy3866
@cryptoozzy3866 2 жыл бұрын
Mate you kind of screwed me!!! You should have told everyone to drain radiator before doing this, it empties the entire supply of coolant straight out the water pump when you remove it!!!! This is like 4 litres or more!!! Luckily I had a bucket underneath. Successfully completed it though, hardest part lining up the bastard gasket and accessing the bolts, the worst was the fact that you have to tap your own thread if you have a FG into that top hole on the pump. Overall though it was pretty decent video and I think we did it ok!
@paulrobinson6168
@paulrobinson6168 Жыл бұрын
Great job on all of the installation of the water pump and accessories, but it have made your job easier if you remove the thermal fan.
@AndyMechanic
@AndyMechanic Жыл бұрын
Lol.. I know that now! Cheers Andy
@AIRMANBEAR
@AIRMANBEAR 5 ай бұрын
I HAD THE TENSION SPRING GO ON A FORD LOOSE SOME OF ITS TENSION AND THE COG BELT WOULD RIDE UP ON ONE OF THE PULLEYS AND IT WOULD CUT THE BELT IN HALF...I COULD THEN GET HOME IF I USED THE 1/2 BELT ... FINALLY I FIGURED IT OUT... ED IN USA
@pe6887
@pe6887 3 жыл бұрын
To seat the o ring into the pipe can aviation glue be used or better Grease??
@rickkhawaja8240
@rickkhawaja8240 5 жыл бұрын
Hi Andy Great helpful video Thank you so much. Kindly if you could answer the following situation. The Water pump was faulty on My Ford EL 1997 and the noise was very obvious. So I changed with GMB water pump GWP3079 + Gates Tensioner Pulley+ Gates Idler pulley. All Went ok But the belt runs close to the edge of water pump pulley (not in the middle of Pulley). It was also like that before the repair job. The belt on all the other pulleys is ok. No noise or squealing. Question is; How can I, and should I move the water pump plastic pulley about 2 mm towards radiator to middle the belt on water pump pulley. Or leave it like that. Thanks
@AndyMechanic
@AndyMechanic 5 жыл бұрын
Hi Rick, it's really important that all the pulleys are in alignment otherwise you'll get belt noise and excessive wear too. You are going to have to move that pulley! Cheers Andy
@rickkhawaja8240
@rickkhawaja8240 5 жыл бұрын
Hi Andy, Thank you very much for your timely advice. I was thinking it is worn bush in the tensioner and hence changing the complete tensioner Assembly.
@AndyMechanic
@AndyMechanic 5 жыл бұрын
Good call & a more likely reason for the belt misalignment, though I have heard that the water pump pulley can be 'adjusted' in some cases. Let me know how you get on. Cheers Andy
@sha514
@sha514 Жыл бұрын
Like your video. I did samen process but water leakage from water pump how I can make sure 0kease guide through installation properly
@magyaradam
@magyaradam Жыл бұрын
Is it all 10m bolts?
@JNemRar
@JNemRar 4 жыл бұрын
Great video! Also what's the hole above where the oring goes.. i took a self tapping bolt out of it but can't remember what it was connected too
@TheOneWhoMightBe
@TheOneWhoMightBe 5 жыл бұрын
Just FYI but I replaced the belt, tensioner, and idler on my BFII and the Idler pulley bolt did not have Loctite/Permatex/etc on it, so ymmv.
@bassemalsaadi1911
@bassemalsaadi1911 2 ай бұрын
Thank you so match
@Brad-yf3zu
@Brad-yf3zu 5 жыл бұрын
Good detailed video, are the water pump bolts with the cut out genuine ford bolts, did you end up using the gasket sealant?
@davidfox2611
@davidfox2611 8 жыл бұрын
If you are working on any late model Australian Ford 6 or 8 cylinder vehicle and need access to the front of the engine then remove the Electric fans. This is a 60 second job and then you have freedom to replace idlers, tensioners and water pumps.
@AndyMechanic
@AndyMechanic 8 жыл бұрын
+David Fox Thanks David, yes, I think you are right. In hindsight removing the fans would have given me more room for filming too. Will definitely do that next time around. Thanks Andy
@siohavili8686
@siohavili8686 5 жыл бұрын
Hi David Fox,please can you let me know how to take off the radiator Ford Territory 2006,i try but its very hard
@alimir5228
@alimir5228 5 жыл бұрын
very informative ..thanks
@BobbyCF
@BobbyCF Жыл бұрын
Why didnt you take the fan off? Two bolts and a plug super easy gives you much more room.
@jockclayton1235
@jockclayton1235 4 жыл бұрын
A 1/4 inch socket with a uni joint and short extension will help do the w/pump up .
@blackIce504
@blackIce504 Жыл бұрын
Bro just a tip with ford falcon's take the rad fan off its easy two 10mm bolts fan power cable and slide and giggle up to give you some room.
@shenghan9385
@shenghan9385 4 жыл бұрын
Why dont you take the cooling fan assembly off. That will give you ample room to do the water pump
@jasonkedwell6103
@jasonkedwell6103 5 жыл бұрын
Great job mate, have an overheating problem with au 4.0 fakcon 2000 model. Mechanic said it was coolant sensor so i changed it, but it overheated while idling again! Water pump does need replacing but not busted. Any thoughts on whether its fans, radiator or water pump? Goes great on the highway but as soon as i get stuck in traffic for a time it starts to get hot. Cheers
@AndyMechanic
@AndyMechanic 5 жыл бұрын
Sounds like it could be a cooling fan issue....as these are important as low speeds - maybe not rotating as fast as they should - tired motor... Cheers Andy
@jasonkedwell6103
@jasonkedwell6103 5 жыл бұрын
@@AndyMechanic Thanx Andy, yeah thats what i think to. I will let u know mate. Thanx for the reply, much appreciated.
@Kitcat8357
@Kitcat8357 3 жыл бұрын
Great job
@samspianos
@samspianos 4 жыл бұрын
Didga change the coolant hoses?one had some gaffer tape on it
@fnq-8890
@fnq-8890 7 жыл бұрын
Cheers Andy I see on you're a Yamaha Wrench as well, which could be handy as I've got a 2012 XT660R with the classic surging problem. I cranked up the CO mixture from 12 to 20 which helped a bit then fitted stage 1 &2 DNA air filters but it still 'hunts' along when in 4th or 5th doing about 60ks .. any advantage do you think in adjusting the TPS sensor? Was going to mark it first so I could reset it back to the factory position .. ??
@justinneumann1492
@justinneumann1492 5 жыл бұрын
Just did the 2010 fg what an absolute pain in the ass cleaning the old gasket of was.
@magyaradam
@magyaradam Жыл бұрын
Hi is it possible to remove just the polly and replace it
@AndyMechanic
@AndyMechanic Жыл бұрын
No, I dont think so, from memory it was pressed onto the shaft.
@magyaradam
@magyaradam Жыл бұрын
How did you remove the actual water pump pully?
@magyaradam
@magyaradam Жыл бұрын
Is it possible to have a lake at the water pump
@johnfletcher1343
@johnfletcher1343 6 жыл бұрын
Great video Andy, but I can't help but think you should be jacking the car up and having a container to catch the anti freeze. Anti freeze is very toxic to the environment even if its on the lawn as the lawn can leech onto other soils.
@Beer_Dad1975
@Beer_Dad1975 6 жыл бұрын
Pretty sure there was no cooling fluid added to that water. Poor old Barra...
@magicheats8291
@magicheats8291 4 жыл бұрын
How hard is it to pull out the fans gees
@leviofford4639
@leviofford4639 5 жыл бұрын
Would there be any reason the bolts on the water pump in trying to take out not clear the pulley at all.
@AndyMechanic
@AndyMechanic 5 жыл бұрын
That's just the design. Odd isn't it? Cheers Andy
@d.i.i7695
@d.i.i7695 6 жыл бұрын
Hi Andy The engine of this Falcon looks exactly like the one in my 2007 ford territory. Does it mean the two vehicle shared same engine?
@AndyMechanic
@AndyMechanic 6 жыл бұрын
Hmmm....possibly a similar version using the same block? Sorry, I'm no expert on these. Cheers Andy
@whitehorse1959
@whitehorse1959 5 жыл бұрын
Yes, same engine - the Falcon and Territory have a LOT in common, not just the engine.
@Brad_hj2tuff
@Brad_hj2tuff 5 жыл бұрын
whitehorse1959 ford territory-oversized ba. They share the same problems like window regs and balljoints lol
@riverrat321
@riverrat321 6 жыл бұрын
Hi Andy, just doing this job now. For some reason I can’t get it out after I removed the 4 bolts, the plate and moved the alternator. It seems like the metal pipe that goes into the pump is stuck in place. Any ideas?
@AndyMechanic
@AndyMechanic 6 жыл бұрын
Sorry Riverrat, have been off-line filming all day. The metal pipe may be corroded or the o- ring/seal dry so the pipe won't come out easily. Maybe some lube spray will help. I did this video quite a while ago so difficult to remember specifics. Cheers Andy
@riverrat321
@riverrat321 6 жыл бұрын
Hi Andy and thanks for the reply. I have been spraying the outside with wd40 and shaking it for days. Been also tapping with hammer. Would it be safe to heat it with a propain torch maybe? Or cut into the old pump to gain better access to inject some wd40? Any other suggestions would be super appreciated! Just shows how things can sometimes go wrong (especially when vehicles have not been maintained). Cheers mate.
@riverrat321
@riverrat321 6 жыл бұрын
Got it off mate. Sorry for all the messages. Thanks for a great video.
@AndyMechanic
@AndyMechanic 6 жыл бұрын
Great job, well done :-)
@quittingyoutube45753
@quittingyoutube45753 5 жыл бұрын
Thanks mate great video I have a few questions though 1. why didn't you use and kind of sealing past when putting the pump on was there a reason why not to do it and 2. Why did you use thread lock on the power steering pump
@AndyMechanic
@AndyMechanic 5 жыл бұрын
Hi Brad, I didn't use any sealant as the surfaces were very clean & in good condition plus, the pump came with a new gasket from memory. Threadlock - well better safe than sorry - no harm in using it just to be sure nothing works loose - driver did a lot of burnouts so high vibration. Hope this helps Cheers Andy
@RangerDanger720
@RangerDanger720 7 жыл бұрын
would you perfer puttnig belt on 1st before the tensioner pulley?
@69jhay69
@69jhay69 6 жыл бұрын
Thanks for the video mate helps a lot :)
@aussie_fisher_guy3052
@aussie_fisher_guy3052 7 жыл бұрын
I dont wanna be rude but its easier if you remove the thermo fans first.
@AndyMechanic
@AndyMechanic 7 жыл бұрын
+MATTS 3030 FISHING you are right.
@coreycarpenter2489
@coreycarpenter2489 6 жыл бұрын
first thing i did when i went to work on my AU
@hasratmohammed5478
@hasratmohammed5478 5 жыл бұрын
Love it
@magyaradam
@magyaradam Жыл бұрын
Did the water pump come with 2 gaskets?
@philliptree1742
@philliptree1742 Жыл бұрын
Yes they do
@magyaradam
@magyaradam Жыл бұрын
@@philliptree1742 mine had 3. Weird
@fnq-8890
@fnq-8890 6 жыл бұрын
Cheers mate ..
@AndyMechanic
@AndyMechanic 6 жыл бұрын
+Queenslander Anytime, pleased you found the video helpful. Andy
@fnq-8890
@fnq-8890 6 жыл бұрын
+Andy Mechanic .. Any thoughts on that XT660 with the fuel surging issue AM?
@susanbutler2199
@susanbutler2199 5 жыл бұрын
I am going to do my car, by myself lol, was wondering when did you use the Yamma bond? Do I need it?
@pingapete666
@pingapete666 3 жыл бұрын
SUSAN YOU ABSOLUTE WEAPON, I hope you did well!
@swamppifi6186
@swamppifi6186 3 жыл бұрын
your comment about matching the water pump because the engine isn't matched , I been caught before, I have a 2007 BF and I been caught out with the wrong oil filter, wrong starter motor, BA is 10 tooth gear, BF is 13 tooth. Repco sales guy has worked out that some one has swapped the BF motor with a BA motor, so I am just about to do the water pump over the next couple of days along with fitting a separate transmission cooler as now I have no idea how much mileage is on my motor....now I been told that the water pumps are the same from 2003 and up..lets see if I get caught again , the cars history is it was a Queensland fleet vehicle for the port authority, then auctioned where the car yard I brought it from , purchase it, I can't see him swapping it, so it is the mechanics at the port authority who swapped it....well done you muppets.... Makes it hard to order parts when you don't have any idea what motor you have, or how much mileage its done....
@tobo26
@tobo26 4 жыл бұрын
Don't you have ratchet spanners?
@AndyMechanic
@AndyMechanic 4 жыл бұрын
I do now! :-)
@TruthHurtLiars
@TruthHurtLiars 4 жыл бұрын
@@AndyMechanic money well spent then
@magyaradam
@magyaradam Жыл бұрын
Three gaskets??
@fordaustralia1814
@fordaustralia1814 9 ай бұрын
Remove the thermo fans for better access...2x bolts and plug.
@Todjlet
@Todjlet 5 жыл бұрын
ON my xr6 turbo water pump there is a plate and bolt on the part with the oring to hold it on not sure how to reinstall it i thin it goest just behind the oring to seal it bit it wont fit i thin is wrong waterpump?
@Todjlet
@Todjlet 5 жыл бұрын
The pipe at the back with the o-ring on it got pushed backed when i was doing up pump making it not seal drained it and test fitted old pump and it had the same gap so ill have to try and undo bolt on side of block to slide it forward again.
@AndyMechanic
@AndyMechanic 5 жыл бұрын
Hmmm....sounds like you are onto it :-)
@Todjlet
@Todjlet 5 жыл бұрын
It had only twisted about 1-2mm just enough to stop it sliding forward didnt have to undo it just twist it back and it slid forward effortlessly then could clamp it with the bolt and tab properly no more leak. Ran the new coolant i added in through a strainer then a fine cloth twice to pick up debris came out rather clean. Thanks for the video andy it was a HUGE help in guiding me through installing all the belt drive pieces! Ordered a power steering pump aswell after the other video as mine was squealing.
@AndyMechanic
@AndyMechanic 5 жыл бұрын
Hey, no problem :-) Pleased you found the videos helpful & appreciate you taking the time to give me the feedback too. Have a great day. Cheers Andy
@anthonycavalliotis8736
@anthonycavalliotis8736 4 жыл бұрын
Remove the fan Old Mate.
@samspianos
@samspianos 4 жыл бұрын
Didn't I tell you before;dont use your hand as a hammer on wrench;in years to come you will pay with nerve damage
@iamasmurf1122
@iamasmurf1122 3 жыл бұрын
running cars without coolant is the main reason stuff like this happens , running just water degrades everything real quick
@AndyMechanic
@AndyMechanic 3 жыл бұрын
Yep & boiling point of the water is lower than coolant too....
@tempest404
@tempest404 6 жыл бұрын
Why didn't you pull out the thermal fans 🤣 sooo much more room to work with
@AndyMechanic
@AndyMechanic 6 жыл бұрын
I do now :-)
@briandickers789
@briandickers789 4 жыл бұрын
when putting Belt on why not remove thermo fans to give you're self more room
@AndyMechanic
@AndyMechanic 4 жыл бұрын
Yes, definitely, easy job but I wasn't aware how easy as this was first time on this motor. Cheers Andy
@potaka79
@potaka79 3 жыл бұрын
'They don't make things easy do they'. Take the fans out you tool, it's 2 10ml bolts
@sehnal139
@sehnal139 7 жыл бұрын
IF YOU REMOVE THE COOLING FAN ASSEMBLY YOU GET LOT OF ROOM.
@rhkips
@rhkips 8 жыл бұрын
I have never seen a modern 4.0L I6 Ford motor before. Looks like it's specifically an Australian/New Zealand thing; never went to any other market. Kinda cool! I want one. :D Pain the butt to work on, it'd seem though!
@Badgertronix
@Badgertronix 8 жыл бұрын
There's a turbo version too! I want one :)
@Beer_Dad1975
@Beer_Dad1975 6 жыл бұрын
I have the Barra 270T variant - mines only putting down 400atw which is about all you can get away with on the standard valve springs - replace those and you can get over 600 reliably on stock internals. They are the Australian 2JZ-GTE equivalent, but even better.
@jaceace2767
@jaceace2767 4 ай бұрын
Slip thre radiator fan out 10 times easier
@user-sp5bn6ye8y
@user-sp5bn6ye8y 4 жыл бұрын
And please...save yourself pain... buy a set of ratchet ring spanners. They're worth their weight in gold when you have situations like those bottom pump bolts
@AndyMechanic
@AndyMechanic 4 жыл бұрын
I have.....about a year ago :-) Cheers Andy
@user-sp5bn6ye8y
@user-sp5bn6ye8y 4 жыл бұрын
@@AndyMechanic haha I'm sure you would have by now 😉. It's more for those who are maybe just going to give this a crack for the first time 🙂👍
@AndyMechanic
@AndyMechanic 4 жыл бұрын
Cheers Wes, yes, it's seems quite some time ago when I did that repair! Feeling a bit older now! Thanks for the comments & keep safe... Cheers Andy
@user-sp5bn6ye8y
@user-sp5bn6ye8y 4 жыл бұрын
@@AndyMechanic haha yeah. I know the feeling there mate! I hate working on cars now. Used to enjoy it but I don't even want to change the oil on them anymore. At 40yo, the fun of the old hobby is gone now and I've moved on to other things
@johnmorris1764
@johnmorris1764 4 жыл бұрын
If you are replacing the pump on a Barra made after 10/2003 you will need a different pump which has a hole for a bolt to clamp the heater pipe and you will need a self-tapping bolt from Ford to fit it.kzbin.info/www/bejne/bpelhJ6udq13rdU
@mikeycawley
@mikeycawley 7 жыл бұрын
I HAVE THE WRONG FUCKING BOLTS! I wondered why when I replaced it none of the bolts seemed to be in the right hole depth wise. Also, mine don't have knicks out of them so I fucked the pulley a lil bit. :(
@mikeycawley
@mikeycawley 7 жыл бұрын
Also, I don't know how you bloody did it with the thermo fans in. I had trouble even with the radiator out lol
@AndyMechanic
@AndyMechanic 7 жыл бұрын
+Mikey Cawley Cheers Mike. Knowing just how easy the fans are to remove from that car (now!) I'd definitely take them out next time! Cheers for the feedback & pleased you found the vid helpful. Cheers Andy
@zonie1953
@zonie1953 7 жыл бұрын
Bosch belt made in China !
@TICKFORDNZ
@TICKFORDNZ 5 жыл бұрын
www.thbunker.com Great vid.
@iraqcom8939
@iraqcom8939 2 жыл бұрын
why are you not start the carYou scared from the lake🤭
@axelfoley1768
@axelfoley1768 5 жыл бұрын
The whole job looked like a royal pain in the ass! Makes one wonder what is wrong with Ford engineers - braindead. There is so much wrong with Ford Falcons & Ford Territorys when it comes to replacing things and servicing stuff, plus convoluted designs and awkward to deal with😠 Do the car designers ever use their brains and take into consideration the fact that mechanics will need to get shit removed, replaced & fixed?😵 Can't wait for electric cars to go mainstream. No more damn engines😬
@shenghan9385
@shenghan9385 5 жыл бұрын
No. Falcon is a relatively easy car to work on. Except of course the heater core. That's a real pain in the ass to even get to.
@AndyMechanic
@AndyMechanic 5 жыл бұрын
Electric cars have their own maintenance issues. Here in NZ you have to have an electrical qualification before you are legally allowed to work on some parts of the vehicle due to the high voltage and huge power packs used. Cheers Andy
@axelfoley1768
@axelfoley1768 5 жыл бұрын
@@AndyMechanic I had the Tensioner replaced last week on my IFord Territory. It is moving back&forward ever so slightly while the engine is on. Is this normal? Someone told me it's normal on Ford Territorys & Falcons. Can you confirm this? I know on most cars the Tensioner shouldn't move at all.
@AndyMechanic
@AndyMechanic 5 жыл бұрын
It will a little as remember the crank shaft doesn't run at a constant speed - it speeds up with each power stroke then slows down again until the next power stroke. The more cylinders your engine has the less this is evident. Hope this helps Cheers Andy
@normshepherd1987
@normshepherd1987 2 жыл бұрын
Joke..
@AndyMechanic
@AndyMechanic 2 жыл бұрын
....okay......Did you hear of the Irish water skier?
@AndyMechanic
@AndyMechanic 2 жыл бұрын
....he spent his entire life looking for a sloping lake.
Yamaha Grizzly cooling fan fault #1414
21:07
Andy Mechanic
Рет қаралды 133 М.
Do you love Blackpink?🖤🩷
00:23
Karina
Рет қаралды 23 МЛН
黑天使只对C罗有感觉#short #angel #clown
00:39
Super Beauty team
Рет қаралды 23 МЛН
Deadpool family by Tsuriki Show
00:12
Tsuriki Show
Рет қаралды 6 МЛН
Cooling System Overhaul on the BA BF Ford Falcon
56:03
Horus Works
Рет қаралды 9 М.
Ford Ranger Belt Tensioner & Idler Pulley Replacement
10:12
ABD Automotive
Рет қаралды 14 М.
Falcon Timing Chain Tensioner
2:41
Craig Wilson
Рет қаралды 78 М.
Replacing Lower Ball Joints on BA BF XR6 Falcon
12:58
Jeenzy
Рет қаралды 6 М.
Squealing from front of your car or truck's engine, not belts? Easily diagnose a water pump
13:14
1A Auto: Repair Tips & Secrets Only Mechanics Know
Рет қаралды 795 М.
BF Falcon 2010, mystery engine noise, oil and coolant leaks.
34:53
Markx Tinkering
Рет қаралды 6 М.
How To Replace a Water Pump and Save $783
13:29
ChrisFix
Рет қаралды 3,1 МЛН
Do you love Blackpink?🖤🩷
00:23
Karina
Рет қаралды 23 МЛН