Ford Fiesta 1.6 Liter Timing Belt Replacement | Mechanic | USA | Filipino | Tagalog

[@wilbertmargallo395]

Dami ko na totonan sau sir Sana someday nakapunta rin ako sa ibang bansa maka pag work as auto mechanic .. more videos pa po sir

[@kuyasautoventure]

Thank you sir..

[@wilbertmargallo395]

Sir panu kapo pala nakapasok jan sir may agency poba sir or nag direct kapo

[@zandymorong5280]

Ganda ng tool mo idol

[@miguelybarra2053]

Those are the only 2 tools you need to hold the stuff in place? I have a 2014 Ford Fiesta 4 cylinder 1.6 I’m changing the timing belt and water pump.

[@kuyasautoventure]

Yes sir, those are the minimum tools you’ll need. I use impact gun to tighten the crank bolt so i didn’t need any other

[@willwilly5723]

@@kuyasautoventure Hi sir, thank for this great and useful video. Did you use other tool to hold the flywheel as you loosened or tightened the crank pulley bolt?

[@bigron26048]

You will also need something to hold the engine while you torque down the crank bolt.

[@bebesitohemoxito676]

I already saw a lot of videos on how to change the timing band of the Ford Fiesta and almost none of them show how to tighten the crankshaft pulley, they only show when the work is finished, I ask you if you recorded the moment, share it, because I have scared of wrecking my car, greetings from Mexico

[@kuyasautoventure]

I’ll just tell you how. With the timing peg still installed, slowly tightened the crank bolt to 74 ft lb. After that, marked the pulley, removed the timing peg and tightened the bolt to 90 degrees , wait 15 seconds and add another 15 degrees. I use impact gun after the initial torquing, don’t over-torque it and i usually use a new crankshaft pulley bolt

[@bebesitohemoxito676]

@@kuyasautoventure thank you, master

[@chunkycheese73]

@@kuyasautoventure amazing!! Thanks for that! There is no info on that! Out here!

[@ആനച്ചന്ദം]

This video very valuable for me thankyou dear ❤❤❤❤🙏🏻🙏🏻

[@dendenbalane9422]

Kuya vintor, salamat po.

[@kuyasautoventure]

Welcome

[@bebesitohemoxito676]

Good afternoon, in the end, to tighten the crankshaft pulley, is it done with the screw that you put back or without a screw, is it the screw that does not allow time to move?

[@kuyasautoventure]

No, the screw needs to be removed for final tightening otherwise it will break. The proper way to prevent the crank from turning during final torquing is by using a special tool to hold the flex plate in place.

[@bebesitohemoxito676]

@@kuyasautoventure ¿impact drill?

[@kuyasautoventure]

@@bebesitohemoxito676 not drill, impact gun you mean? I supposed you can use an impact gun

[@atletangofw1989]

Hello may nabili kami 2012 ford fiesta. Masa suggest jyo ba palitan na ang timing belt, tensioner and water pump? 62 thousand km na ang takbo

[@reynaldopamplona6020]

Present lodi

[@kuyasautoventure]

Salamat sir!

[@nelbdeguzman]

what will happen if you loosen the crank shaft pulley and it turn counter clockwise?

[@mackoy1358]

Meron po na markings na sundin timing gear SA Baba? O kahit among position?

[@jierolanceconia5129]

thank yuo sir.god blees. saan po pwisto mo.

[@neilbalangyao-qy5iq]

Halo sir paano po kng naikot po ang cammshaft po ano pwd gawin samalat po

[@benedictjohn848]

What is the size or specifications of the serpentine belt for ford fiesta?

[@francisrosario9222]

sir kng wla kng tools n ganyan pwd bng mgpalit ng timing belt my gnwa kc kmi dnmin gnmitan ng tools n gnyan

[@ആനച്ചന്ദം]

Thankyou so much bro

[@bernonleocario4153]

Question po sana. If mag replace ba ng timing belt need ba ma down yung makina? Many thanks 🙏

[@dedywahyudiyanto9207]

Ia it to lossen it ? Mine got stuck

[@blackmammoth3022]

Sana soon makapagwork aq jn idol 🙏

[@melclydefredmanigbas5592]

Good day ask ko lang ano po ba mga symtoms na palitin na timing belt

[@kuyasautoventure]

Wala po sir, by mileage/time lang po yan. Wag po hintayin maputol, masisira makina. Pa check muna condition kung hindi alam kung kelan nagpalit.

[@melclydefredmanigbas5592]

@@kuyasautoventure hindi po ba sya nakaka apekto din sa pag hahard starting.Thank you sa responce

[@kuyasautoventure]

@@melclydefredmanigbas5592 kung stretch na pwede mawala sa timing, but you would have other issues like check engine light or lack of power, but if you’re asking about specific symptoms that indicates it’s time to replace the timing belt, wala ako maisip specific to timing belt (noise maybe???)

[@melclydefredmanigbas5592]

@@kuyasautoventure thank you again po sa responce,yes po sir nagkaroon po sya mg check engine light sa dashboard at yun nga po hard starting na po sya pag na timingan po nag sayart sya pero once na nag off engine na ulit ako pahirapan na ulit sya mag start posible po kya gawa din sya sa timing belt na need palitan

[@GearHeadPH]

Hi sir, ask ko lang kung may space po ba for impact gun para matanggal yung crackshaft pulley? Pwede din po ba na socket wrech lang ang gamit or need talaga ng impact gun? Salamat and more power po.

[@kuyasautoventure]

Mahigpit yan sir, gamit ka ng impact pang tanggal, maliwang po yan, ibaba nyo lang po siguro bahagya yung makina after removal ng mount. Pag higpit ang tamang tools ay socket wrench, pero walang kunya ang crankshaft kaya dapt saktohan ang higpit, i use impact after initial torquing ng bolt. May stages kasi yung pag higpit

[@GearHeadPH]

@@kuyasautoventure maraming salamat sir sa advice. Plano ko po kasi diy magpalit ng belts. yung ibabayad ko for labor, ipambibili ko nalang ng tools para invest ko na din. Again, thank you sir and more power sa channel mo.

[@GearHeadPH]

@@kuyasautoventure sir, kakayanin po kaya ng mga cordless impact gun para matanggal po yung crankshaft pully bolt?

[@kuyasautoventure]

@@GearHeadPH matigas yan masyado, i doubt it

[@markstevesayat6439]

Boss HM po pakabit ng Timing Belt ng Ford Focus

[@jaypeebandialan5362]

Boss yung timing kit po ni ford fiesta same lang po sila ni ford ecosport? Tnx boss godbless!!!

[@kuyasautoventure]

di ko alam makina ng ford ecosport dyan eh

[@ആനച്ചന്ദം]

Uploaded more cars video i will support u😍

[@B.J_tv]

Lods pano po tanggalin yung crankshaft timing gear di mo pinalakita eh cut mo ung video

[@kuyasautoventure]

Impact gun (1/2 inch drive)

[@dendenbalane9422]

Kuya vintor, yanh po bang inilalagay sa may crank shaft na turnilyo ay naglalock sya?

[@kuyasautoventure]

Parang stopper lang sya, kapag tumama yung counterweight nung crankshaft TDC yun, panuodin mo yung iba ko pang mga videos, makikita mo yun

[@kuyasautoventure]

kzbin.info/www/bejne/aKPCfpSBrpKcp9E

[@dendenbalane9422]

@@kuyasautoventure salamat po uli. Ok po

[@forexsurfer3830]

Kuya Kabayan walking Timing belt sa akin. 2008 Ford Focus mk2 16v 1.6l . Already check tensioner, sprocket. Noted the right side of the belt is less tight than the left side or tensioner side of the belt. Please could you help me troubleshoot this problem.. maraming salamat ng marami Kabayan Kuya.

[@miosoul9559]

bos ano nilagay mong torque sa crankshaft bolt?

[@kuyasautoventure]

74 ft lb, 90 deg wait 15 sec then another 15 deg

[@miosoul9559]

salamat bos. bos ano naman diskarte para luwagan ang crankshaft bolt? tingin ko kase hinde pwede sa ford yung lalagyan ng breaker bar tapos ecacrank para lumuwag ang bolt. saka sa paghigpit na din ng bolt pano diskarte pwede na ba yung pin stopper sa gilid ang gawin pangkalso para mahigpitan ang crankshaft bolt?

[@djsportsofficial2268]

Lods I'm new subscribers. from west Sacramento California. And I want to be Auto Technician. Ano unahin ko lods bago maging Auto Technician.

[@kuyasautoventure]

Go to school, i went to a community college to get may automotive tech associate then take ASE tests, then look for a job, at magbaon ng maraming lakas ng luob

[@djsportsofficial2268]

@@kuyasautoventure thank you sir. I appreciate it

[@zandymorong5280]

Boss idol meron po bang nabibili niyan sa shoppe

[@kuyasautoventure]

Lazada sir meron,

[@zandymorong5280]

@@kuyasautoventure sir anu pong pangalan ng tools na yan sir

[@zandymorong5280]

Sir anu pong pangalan ng tool mo meron po ba niyan sa shoppe sir nahihirapan po kasi ako mag palit ng timing belt kasi wla akong ganyang tools

[@kuyasautoventure]

www.lazada.com.ph/products/engine-timing-tool-kit-for-ford-16-ti-vct-16-duratec-ecoboost-c-max-fiesta-focus-i301386157.html

[@johneemotovlog2073]

sir, kadalasan ba cause ng P0016 and P0017 is timing belt maluwag/stretched na siya? 90k+ kms na tinakbo. Thank u

[@thomasstifler7461]

up ayos naba p0017 mo?

[@johneemotovlog2073]

@@thomasstifler7461 oo sir, change timing belt and re-timing ng camgears/camshafts.

[@thomasstifler7461]

@@johneemotovlog2073sir, magkano binayad mo sa re-timing?

[@johneemotovlog2073]

@@thomasstifler7461 nasa 2500+ sir

[@reymariecruzat6346]

Saan po ang shop

[@kuyasautoventure]

San Diego California po

[@rodelperlas4403]

Magkano Pagawa..timing belt..

[@kuyasautoventure]

Nasa US po ako sir, pero kung experienced yung gumgawa nasa 4 hrs kuha na yan, kelangan lang marunong kasi walang keyway yung crank, papalit na din ng water pump at the same time

[@trashtalkemperor]

isa sa pinaka wlang kwentang makina yan ng ford wlang keys ang crank gear anu kya naisip ng ford pra khit i resurface ang head or block match pa rin ang timings 🤣

[@hughbunyea4703]

So I'm not a mechanic but I have down some major repairs on my vehicles over the past 40 plus years. 2017 Ford Fiesta 1.6 non-turbo. The timing belt walked so now I'm in the process of trying to change it. I ordered the two tools you show, cam holders and crank pin. My concern is why do I see other videos showing the valves, starter and axle having to be removed. If I put the cams at top dead center like you show then install the hold can't I then install the pin remove the crank or can the something turn and screw up everything. Thanks

[@chrismyers9951]

On fiesta st 4 cyl turbo starter removed so flywheel tool can be installed so crank bolt can be removed (must use new bolt with torque and degrees spec. Half shaft removed to install crank pin. Also tool to hold cam phazers in position. Also bar to hold cams in place. No locator pin on crank pulley on these engines.

[@chrismyers9951]

There is also a tool that replaces the crank sensor so the crank pulley goes back on in the correct position.