Ford Focus Purge Valve Replacement! 2012-2018 2.0L Duratec

Dorman Purge Valve: amzn.to/3HVOBgh
Buy me a coffee! buymeacoffee.c...

[@BigBensCarsAndCycles]

Dorman Purge Valve: amzn.to/3HVOBgh

[@AmrYoussef-s5o]

My ford focus is 2015 SE 4 cylinders 1.5 L echo boost had turbo oil leak after 110 k miles due to using bad oil or different oil … I think

[@lmaotravis3702]

With 0 mechanic experience I got an OBD2 device and got this done in less than 15 minutes. Solved all the issues. Awesome video and super easy to follow!

[@BigBensCarsAndCycles]

Awesome! Glad to help

[@HTXVintageVibes]

With 6 out of 10 mechanical experience it took me about the same. Great instructions honestly.

[@narcodicts]

Also 0 mechanic experience. But had my step dad help me. He didnt have me remove the whole intake compartment. Just the part that is hose clamped on (the tube itself.) Seemed less steps that way.

[@HTXVintageVibes]

Will say the thing that hung me up was not only does it use Freon 6-7x more expensive it comes in 8oz cans, and require a new set (the correct set) of gauges and tools to refill. Was able to do all the work myself and rent the tools, vacuum the line, do it all correctly and still cost me nearly 400$. Had it been the traditional 134a it would have been 60$. Be prepared!

[@thapelomonqa3445]

Which OBD2 device did you use?

[@taunus1979]

Thank you so much! I changed the purge valve in my 2013 Focus using your video, and your explanations were crystal clear. My car had error codes P2196 and P144A before, but now they are gone. The issue was stalling and stopping when filling the car, but now everything works as it should. Thanks again!

[@BigBensCarsAndCycles]

Awesome! Glad you're all set. Happy driving!

[@taunus1979]

@@BigBensCarsAndCycles may I kindly ask what should I do for P0131 (02 Sensor Circuit Low Voltage Bank 1 Sensor 1) code? Thank you so much!

[@BigBensCarsAndCycles]

@@taunus1979 install a new oem or Bosch upstream o2 sensor. You're welcome!

[@taunus1979]

@@BigBensCarsAndCycles perfect, subscribed and will check all the content. There are lots of useful tips in the channel. Thanks again!

[@Slimpster520]

This is literally the best car work video i’ve ever seen dude. I don’t even have this car, but now i might do this for my mother in law because you made it so CLEAR.

[@seancostil8335]

I think this has to be the best tutorial I’ve ever seen on KZbin about anything. Your frickin rock dude!

[@BigBensCarsAndCycles]

Awesome! I'm glad it helped

[@mstee6738]

Agreed.

[@FITE4self89]

Damn. Sitting at the dealership at this moment and I could’ve saved myself a bunch of money had I found this video sooner.

[@jamilqarqash8078]

I have zero mechanic experience and your video helped me to replace mine in 20 minutes. Thanks sir 😁

[@potski706]

Bravo good sir! This may be the best focus repair video I have ever seen! Very detailed instructions and amazing video work! Thank you a million times!

[@BigBensCarsAndCycles]

@@potski706 you're welcome! 👍

[@joemartinez6182]

Great job in explaining how to replace the purge valve now I'll tackle the job, thanks a bunch.

[@xtsoler]

Many thanks for the detailed video. I did replace mine as well with the slight variation that I didn't remove the whole air filter assembly, only the large rubber trubing by removing the retainers in both ends. I couldn't pull the air filter assembly enough to get it to pop and was a bit afraid not to break anything. But it all worked out fine. Many thanks again

[@BigBensCarsAndCycles]

You're welcome! And good idea with that hose!

[@riderreviews3737]

Awesome video bro. Literally the best I ever seen on KZbin. I'm planning on tackling this job on my '18 Focus with p1450 code. Rough starts or sometimes just stalls after filling up gas tank but I've heard some people's focuses will just stall mid-drive if the problem isn't fixed. Anyways, thanks for the detailed tutorial and time you took to record and upload the video 🙂

[@BigBensCarsAndCycles]

You're welcome!

[@darrenkirgira3386]

any update on if this worked for you?, having the same issue in my 2018 focus

[@briansettles2455]

After removing the hose from the throttle body and ensuring that their is no debris in it either stuff a rag in it or cover it with a plastic bag to ensure nothing falls in it. Be sure to remove the rag or plastic bag and make sure it is clean before reinstalling hose.

[@AGaymer2319]

Lighting 10, camera angles 10, demonstration 10, explanation 10. 10s 10s 10s across the board

[@willm5375]

thank you for the video ! I was able to get everything done and it's running better and no more funky startup after filling the tank. also you can buy the part at your local Ford dealership I went ahead and just put an OEM Ford part back in because it was cheaper than the dorman and its lasted 136,000 miles so it must not be a terrible part

[@-B-RAD-B-]

Ty sir. Made this fix painless. My issue arrose after a fuel injector cleaner treatment. *lucas oil brand*. Symptoms were rpm drop when slowing and coming to a stop and fuel guage reading more than actual fuel level. Thanks again.

[@SuperFpac]

i know nothing about cars and this was so helpful and easy to follow. thank you!

[@ChrisVog]

Saved me some money with this one. I changed this part with a new one and reset the check engine light. Drove it around a bit but the light hasnt popped on. I ran the diagnostic computer expecting to see nothing but the p0456 code saying "Permanent" even though everything has been running like new again.

[@BigBensCarsAndCycles]

Glad it helped. That permanent code will go away after a while..once the readiness monitors relearn

[@CarlBarelli]

Thanks for the video. I have a P046 code and just swapped in the new purge valve. I did snap off one of the two the plastic mounts on the bottom of the air intake box while removing it but fixed it with duct tape ;).

[@bmrjck2315]

Thank you! Fix this part on my 2014 Ford Focus with no problems. Great instructions!

[@kingarc5997]

Pretty simple video. Just did this on my Ford Focus 2016 SE.

[@Sulfen]

Thank you. My dad's car showed this code a few weeks ago and I was trying to find a solution to a problem he had with his oil but I could not connect the two until I saw your video. When you mentioned the code P1450 the code seemed familiar and I quickly got my OBD2 reader and pulled up the history and sure enough same code.

[@BigBensCarsAndCycles]

You're very welcome!

[@paperhero1081]

Thank you for the easy to follow video. I knew nothing on how to do this but watched your video step by step and I did it. pretty easy. You are awesome

[@BigBensCarsAndCycles]

@@paperhero1081 I'm glad it helped!

[@aknczz]

Thank you so much men I just did it by myself without experience of any type of mechanical adventure

[@BigBensCarsAndCycles]

@@aknczz awesome. Glad to help!

[@aknczz]

@@BigBensCarsAndCycleshey men it fixed for a day but it just happened again rpm hitting and down do u have any suggestions

[@corinnemartin5528]

I feel like you could teach me anything! The tutorial is top notch.

[@BigBensCarsAndCycles]

Glad it helped!

[@RaffyOzuna]

DE TODOS LOS VIDEO ESTE ES EL MEJOR EXPLICADO,,,LOS DEMAS TIENEN QUE VER ESTE ..PARA QUE HAGAN LOS VIDEOS ASI CON SUS DETALLES,,,,(GRACIAS MILL)

[@BigBensCarsAndCycles]

de nada! muchos gracias para ver (lo siento por mi espanol)

[@Harryus10]

You are the best! There was a code P0087 (low fuel pressure) on a 2017 Ford Focus S. Now everything works fine. It's just a pity that I changed the High Pressure Fuel Pump and spent a lot of money, but now I can not worry about the fuel system.

[@BigBensCarsAndCycles]

Glad the video helped. The purge valve shouldn't cause that code. You may need a low side fuel pressure sensor. I have a video on that, too. It's easy to do

[@Harryus10]

@ Thank you for your reply! The issue was actually with the purge valve - after replacing it, all the jerking and shaking stopped. However, I’ll keep your suggestion in mind in case any other fuel pressure issues arise in the future. Your video was really helpful in understanding the problem!

[@SinisterPlot]

Great video man! By far the best I’ve seen on this topic, I just changed out the purge valve on my 2015 focus! Had the P1450 and P0507 codes. Hoping this works, probably will cause I was having bad engine surges after getting gas. Thanks for the video!

[@Cai1900-f8e]

Same ..where did you got the tools will someone lend tools

[@tylerpedigo1614]

Great video man! My check engine light came on in my 2018 ford focus and found out it was the solenoid and thanks to this video I changed it out in 5 min.

[@BigBensCarsAndCycles]

Awesome! Glad to help

[@jnunez9771]

Thanks this was the issue that i fixed just from your video much appreciate it

[@joescott4545]

Here I go ! Attempting to install. There are too many problems from code and hope this fixes. Fingers crossed.

[@chasehalverson3692]

Loved this video. Question. After I installed the purge valve I cleared the code but when I check my code reader there was a code for dtc definition not found. There is no code on my dash board, only the obd2 reader. Should I worry about it or just leave it alone?

[@BigBensCarsAndCycles]

did it give you a code number or anything? I'd probably not worry about it

[@manuyank]

Thanks for sharing this video. Very well described. Got mine done in about 30 minutes.

[@BigBensCarsAndCycles]

You're welcome! Glad to help

[@tylerlee4748]

This was amazing!! I had it done in about 20 minutes! Thank you!!!

[@scrubtug6507]

Extremely helpful. Thank you sir!

[@BigBensCarsAndCycles]

Youre welcome!

[@jibburz3030]

Straight to the point great tutorial

[@BigBensCarsAndCycles]

You're welcome! Thanks for watching

[@matthewsmith9410]

That's a lotta acorns! Great video

[@tjwadsworth6967]

Thank you! My problem was i'd be driving on the highway in the heat and lose all throttle and it would stall out, sending me to the side of the road. Still worried to take it out after replacing the purge valve, but do you think that should have solved it?

[@DrFantazmo]

Thanks for the great video, exactly what I needed and it went very smoothly with your help.

[@BigBensCarsAndCycles]

Awesome! Glad to help. Happy driving

[@GenWebber]

Got me thinking I can change this myself. But first, does P1450 always mean the purge valve needs replaced or should other things be checked before swapping it out?

[@WENYINGWANG-oi9rp]

Thanks to the video otherwise I couldn't change the purge valve, Big Shout out to Big Ben! May I kindly ask why the engine is still on after I replaced the purge valve since I got code P0456? Will it disappear later or I should drive for a while to see...

[@BigBensCarsAndCycles]

I'm glad it helped. You can clear the code with any cheap scan tool

[@tylersimpson3512]

Did the code go off after you replaced it?

[@robertl2227]

Great vids. Sounds like someone who used to teach kindergarten

[@handmouth]

Well done you saved me money. Thank you.

[@andrewgolda9949]

I've seen several videos replacing either the purge valve or the whole assembly. I'm not certain which one I should replace but I do have p1450 and p0456 codes

[@BigBensCarsAndCycles]

You should get a bv6z-9d289-r (oem purge valve). That's all you'll need.

[@WENYINGWANG-oi9rp]

@@BigBensCarsAndCycleshi i just if the Dorman 911-777 Vapor Canister Purge Valve the same thing as Bv6Z…

[@offthecouch1999]

Dude youve got a sub. Thanks for making a video i can follow along with so well.

[@BigBensCarsAndCycles]

Happy to help!

[@soytitv4114]

I will try this by myself. Every time i fill up gas on my Ford focus titanium 2017, it is so hard to start ..

[@HTXVintageVibes]

I was stressing at first. I swapped the purge valve out and the code wouldn’t go away. I didn’t realize I had to clear it first 😂

[@BigBensCarsAndCycles]

Glad you got it fixed 👍

[@SAMEntalhealth]

Are these clipless? My new purge valve came with no clips just gray, on the pushes. But no clips do I need to put my old clips in?

[@BigBensCarsAndCycles]

Hi, some aftermarket ones are that way. Thats fine just push it on and itll click

[@jashaungarrison1980]

Dumb question. After I cleared the code and drove around I plugged the OBD reader again and it still gives me the P0456 code but the check engine light doesn’t come on. Anything else I should try?

[@BigBensCarsAndCycles]

It may be reading it as a permanent dtc and you'll need to complete the readiness monitor for it to clear. It'll do that on its own in a few days

[@jashaungarrison1980]

@@BigBensCarsAndCyclesOk thanks for the response😁

[@docrinkergarage]

Over 1k subscribers!!! That’s awesome

[@BigBensCarsAndCycles]

I appreciate it so much!

[@shaughnessyparks]

Thanks for the video! But wouldn't have been easier to just remove the intake hose?

[@BigBensCarsAndCycles]

Yup! You can do that too.

[@YuTbCensorship]

What size Socket ? US Standard or Metric Socket ? Thanks for showing how to change this part....I'm sure if I had the Ford Dealer do it would be $500.00

[@BigBensCarsAndCycles]

You're welcome! 7mm for the hose clamp on the air intake hose (8mm on 2012s)

[@YuTbCensorship]

Thanks. I'm rewatching your Video. Planning to do this repair in about 15 minutes. Unfortunately I purchased a small screwdriver to loosen the clamp. And a long Screwdriver since no Cat Claw. I'm traveling for work and doing this in the Motel Parking lot. Purchased replacement part from O'Reilly Auto Parts in Georgia. Wish I had seen you reply earlier before buying tools. I have a 7mm/ Socket set at home somewhere in my Garage in NJ

[@BigBensCarsAndCycles]

@@YuTbCensorship it'll be fine. The clamp has a flathead screwdriver provision

[@GenWebber]

Does P1450 always mean the purge valve needs replaced or should other things be checked before swapping it out?

[@BigBensCarsAndCycles]

99% of the time its the purge valve

[@mahmoudfayed6782]

What are the symptoms of damage to this part? Is the reason for the release of a quantity of air when inserting the fuel gun considered a symptom of damage? and it is the same location in focus 1.6 ?

[@BigBensCarsAndCycles]

Hi, the 1.6 is similar. The failed purge valve can cause engine lean or rich depending on how much fuel its pulled through the canister

[@corym8441]

Just used your video to take care of my purge valve in my 2018 Focus. But I always worry that I didn't put something back right and my car will explode.

[@BigBensCarsAndCycles]

I'm glad it helped, you'll be fine!

[@darrenkirgira3386]

what was the code your's was throwing before you fixed this issue?

[@dizzyman1167]

Out of curiosity when is the check engine light supposed to disappear? I don’t have much knowledge on cars or codes but I just changed mine a good 15 min ago does it take days or???

[@BigBensCarsAndCycles]

@dizzyman1167 you can clear it with a scan tool, or have an auto parts store do that. Or, within a few days it should on its own

[@andrewchapin3894]

I have been investigating my P0420 code (catalytic converter) and see that some people are saying that replacing the purge valve will help. I am quite certain it is NOT a cat problem and related to the sensors. The code is very intermittent, it will even go on and off during a single drive. I do not have any of the sounds people say attribute to a bad cat. Any advice here?

[@BigBensCarsAndCycles]

The cat is a very common issue on these, normally they just set a p0420 code and that's it. Yes, if the purge valve is leaking it can cause the code if the air fuel mix isn't correct. You can try replacing that first, and doing a tune up..and maybe the upstream o2 sensor. If you still have the code, I'd put an o2 spacer on the rear o2. Or spend 1400 on an oem cat. Up to you lol. Aftermarket cats are cheaper but will start setting p0420 again within months

[@seanconery]

Do I need to have the computer reset after this? Or will the check engine light go off on it's own?

[@BigBensCarsAndCycles]

@seanconery it'll eventually go away but I'd at least have autozone reset the code for you

[@rhictis6444]

Hey there, trying to do this myself now, and what's the size of the socket and/or the name of the powered wrench you're using? Great vid btw

[@BigBensCarsAndCycles]

I'm glad the video helped! It's a Milwaukee m12 1/4" ratchet

[@jayfogz]

I got a p2196 code right after filling up, didnt notice it being hard to start. I'm pretty sure I had the recall done when I recieved the notice. Is it the purge valve or o2 sensor?

[@BigBensCarsAndCycles]

It is possible they reprogrammed your car but didn't replace the purge valve because it wasn't bad then

[@jayfogz]

I pulled the line off and it didnt have any vacuum so. I did clear the code right after so will have to wait and see if it pops up again

[@someskinnydude100]

I have a p0456 code. It says to replace the canister purge control valve. Is this the same thing?

[@BigBensCarsAndCycles]

@@someskinnydude100 yes

[@someskinnydude100]

@BigBensCarsAndCycles another question. You said at the beginning of the video that if I remove the clips from the sensor to the back side of the connector that I would be able to tell if there is a vacuum present. That won't mess up the engine right?

[@someskinnydude100]

@@BigBensCarsAndCycles so far I did it and it doesn't feel like there's a vacuum in the hose.should I still replace it if it says I have to?

[@julianleal5165]

Thanks for the help. I hope that fixes it

[@BigBensCarsAndCycles]

It will fix codes p1450 and p0456. Also several other symptoms and codes. What issue are you having?

[@reyrey90_60]

Do you have the part number on the abs wheel speed sensor for passenger side

[@taeka-d9o]

Wow great video thank you so much.. is this the same as the EVAP purge valve? Thank you

[@BigBensCarsAndCycles]

You're welcome, and yes - it's the same part

[@taeka-d9o]

@@BigBensCarsAndCycles thank you my engine light was on yesterday and its about that according to autozone.. but today the light turns off.. its weird

[@Lucaschiarelli12]

My fuel gauge indicates more fuel than it should. The marker never indicates fuel in reserve. Would the problem be the purge valve?

[@BigBensCarsAndCycles]

Yes that could be the purge valve, but also make sure your gas tank isn't sucked up from the purge valve pulling vacuum. The dealer can check that and there was a recall on it

[@OfficialFTG]

How do you pull the hose off the throttle body? I lossened it but still stuck

[@BigBensCarsAndCycles]

Hi, you can run the engine with the hood closed to warm the rubber. Or use a blow dryer

[@OfficialFTG]

Any advice on how to actually disconnect the part? I cant get those green conectors to come off on either side

[@BigBensCarsAndCycles]

@@OfficialFTG push the hose inward, push down on the release, then slide it off

[@DustinH2049]

Is this why my focus is hard to start after putting gas in it? No check engine light

[@BigBensCarsAndCycles]

Yes, most likely

[@DustinH2049]

@BigBensCarsAndCycles thank you so much. You're videos have been amazing to get to know my new car

[@YeymyBeCute12]

How do you replace the fuel line to the high pressure fuel pump? My ford focus is leaking fuel from the line

[@BigBensCarsAndCycles]

The low pressure line appears to come as an assembly with the lines going all the way to the back of the car. If you suspect just the o-ring leaking you can try matching that one up but make sure it's exact and rated for fuel

[@shellyalshahiri9050]

So where exactly is it under the air filter box or what sorry I’m Dumb founded as I no mechanic

[@BigBensCarsAndCycles]

Removing the airbox only helps with removing it and it's not totally necessary

[@Blends99]

Can this part possibly cause the engine to knock?

[@BigBensCarsAndCycles]

If it leans the engine out enough it's possible

[@adolfosandoval7523]

Great job sir ...but why not blow all that stuff before you work in a car ....it only takes one min😢

[@BigBensCarsAndCycles]

@adolfosandoval7523 hi! Glad it helped. I cleaned up after. I remember because I was doing a tune up afterwards

[@AmrYoussef-s5o]

Sorry to ask … what is OBD2 …??

[@BigBensCarsAndCycles]

Vehicle link interface for a scan tool. The plugin under the dash

[@AmrYoussef-s5o]

Thank you 🙏 brother

[@lilibethpr1922]

Where does the transmission vent connects to?

[@BigBensCarsAndCycles]

It slides into a hole near the range sensor

[@Mozart0230]

What are the symptoms of a bad purge valve, is thisbthe same as the solenoid

[@BigBensCarsAndCycles]

@Mozart0230 hi, yeah same thing. Code p1450 is common. And a rich or lean condition. P0456. P0420 can be caused by it. P0171.

[@Inkadomination]

Why was it replaced ?

[@BigBensCarsAndCycles]

P1450 is the most common code for it. It can also cause a lean or rich condition. Depending on if the canister is flooded.

[@Inkadomination]

@@BigBensCarsAndCycles I have a sound when I crank to start. I hear people’s cars sound normal crack and it starts. Mine doesn’t sound like starts it’s hitting but like if the car sounded old . Like how them old cars start their engines . Idk what it could it be

[@BigBensCarsAndCycles]

@@Inkadomination I just saw your comment. If you want to post a short video of that on my discord I'll take a listen

[@DetroitMicroSound]

Poor abused girl. 😥 All the grunge says it all....then the fact nature decided that was a new home to move into.....

[@BigBensCarsAndCycles]

If it were mine, I'd take great pleasure in cleaning that all up

[@DetroitMicroSound]

For sure. Just because Ford used plastic everywhere under my hood, doesn't mean it shouldn't be clean, and cared for. Everybody uses plastics. There is art in aesthetic design appearing in polymer parts design, by all companies still producing ICE CARS...the headers on my Fiesta....plastic-coated.... but somehow, still aesthetically pleasing.....and taking engine head covers off, keeps our engines cooler.... if you don't live in arctic conditions, you DON'T want a head cover.....@@BigBensCarsAndCycles

[@YeanMachine]

should you disconnect the battery first?

[@BigBensCarsAndCycles]

@@YeanMachine doesn't matter

[@sevvislowes7937]

What size socket do u use

[@terr256]

I replaced mine 2 years ago and this came up again :/

[@BigBensCarsAndCycles]

Did you use oem? That should last 5 years plus

[@CephalusCapone]

air blow the engine sir!!

[@robertl2227]

Owners problem, not mechanics

[@nbk64uv]

Who on Charlotte that can come replace mine

[@ericbrown3881]

The real story here is how the creator pronounces "debris".

[@BigBensCarsAndCycles]

Debrisss

[@looseparts]

I seriously wonder if I can pull this off as a left handed person ; -) I'll let you know next week : -)