Hey mate, I'm just about to put a 2" lift in my bt50, your video was one of the most helpful, have done plenty to GQ & GU's, first time owner of bt, so thanx and keep the shiny side up 👍👍
@AUZUP4X43 жыл бұрын
Thanks mate good to here that I could help out
@gailmaplesden73802 жыл бұрын
This is the first video I've seen where they did a carrier bearing drop. Was the diff already dropped on this build .
@AUZUP4X42 жыл бұрын
Hey mate no it wasn't it this car was all standed before the suspension swap cheers
@scottcolman38333 жыл бұрын
I see you flipped the drive shaft carrier. is that the fix for drive shaft with lifts? Some kits talk about a drive shaft spacer kit??
@AUZUP4X43 жыл бұрын
Yeah mate its so you don't have to use the spacer kit I've had it in for over a yr now and have had no problems with it
@marcusbarnes59292 жыл бұрын
Do you know how many mm is the offset when flipping the drive shaft centre bearing bracket? How much does it drop the centre bearing to stop vibration. And does your ford ranger shudder when taking off from a stand still at all ?
@AUZUP4X42 жыл бұрын
Hey I'm not Shore of the off set. this is what I have done to all the lift kits I have in stalled to rangers. Also not I do not get any shudder at all
@marcusbarnes59292 жыл бұрын
@@AUZUP4X4 I installed on my PX3 the dobinsons MRR 3 inch front 2 inch rear . I'm using the dobinsins spacer at 4 washers which is 16mm. I get a slight shudder between 10km/h and 15km/h. Getting slight shudder on take off from trafic lights. I will flip the centre braket and see if it helps. Thanks 👍
@ottomunkel17413 жыл бұрын
Does the US version have the same suspension as the Global Version? I wanted to buy the 2inch BDS leveling kit, for the global version, but I’m not sure whether it’s gonna fit
@AUZUP4X43 жыл бұрын
Hi there I wouldn't be 100% shore but I wouldn't think it would be that different
@shilinzhang77453 жыл бұрын
useful and great video.
@AUZUP4X43 жыл бұрын
Thanks mate
@comeatmeathlean36393 жыл бұрын
At 15.25 secs.. what did he do there?? Did u had to do a diff drop?
@AUZUP4X43 жыл бұрын
All I did was flip the center bearing as thay are off center, also no I didn't put a diff drop in as thay are only set to 2 half inch
@amsoil86693 жыл бұрын
Upper arm std can support how many high ? 3.5inch lift can?
@AUZUP4X43 жыл бұрын
As im told up to 3" thats it
@amsoil86693 жыл бұрын
how many mm thick spacer was used previously?
@AUZUP4X43 жыл бұрын
I had 2" in it mate
@amsoil86693 жыл бұрын
@@AUZUP4X4 2"=50mm? So high lift 3inch when use spacer 2" thick
@AUZUP4X43 жыл бұрын
@@amsoil8669 hey mate sorry what do you mean
@A.A.HadiWhite2 жыл бұрын
hi Auzup4x4 do you recall the size of the pin on the rear block lift?
@AUZUP4X42 жыл бұрын
Hi there sorry what do you mean mate
@A.A.HadiWhite2 жыл бұрын
@@AUZUP4X4 rear lift has a metal block that you place between the leaf spring and axle, on the same block there is a pin (botton) on one side that fits and a hole on the other side, one end fits into the leaf spring and the other end fits on to the axle to keep the block in place. Do you remember the size of the pin on the block?
@stevemassarii40532 жыл бұрын
Hey mate, can you send me a link to what lift this is ?