Ford Rocam valve timing

How to do the valve timing on a Ford Rocam engine

[@danjemane965]

Straight and forward explanation Thanks very much on point

[@carburettorrebuildservice8964]

Thanks for watching my videos.

[@davehamlyn3097]

Rocam is not in the Figo. Rocan for the South Africam Market is in the Ka, Bantam, Fiesta and Ikon. Anyway, Thanks, This was a great video clip.

[@williamswart6835]

Thanks this helped alot.. Busy rebuilding a rocam motor... After I bought one with bent valves

[@carburettorrebuildservice8964]

ek is bly ek kon help, voorspoed

[@bevanoneill9448]

Dankie oom se video het my weer gehelp

[@lvmoja]

Thanks for the video. It was very helpful. My 2004 Ford Ikon had the same problem with the chain guide breaking and the broken pieces ending up in the oil pick up. In my case I ended up with one of the piston rods punching a hole in the block!

[@carburettorrebuildservice8964]

thank you for the good review.

[@bobbymccracken5844]

This is better than, haynes workshop manuals, I’m looking forward to more this.

[@carburettorrebuildservice8964]

thank you for the feedback. it means a lot

[@djgeefunk4090]

very good instruction of this video for the ROCAM i am also busy with complete engine overhaul 2 cylinders dropped compression no 1&4 120psi no1 no2 150 no3 150 no4 90psi so after strip discover bad bore and noted prior to strip engine tappet cover oil filler was full of oil blow by crank case ventilation also further stripping engine bores were scored with vertical marks in bore well engine is at the engineers mic up and advised we require oversize 20thou and also the block requires decking slightly due to the engine overheating matter i suspected, these parts are very costly R18000 in total for everything my next worry is the feedback from engineers on the cylinder head i applied a straight edge and i CLOSED MY EYES after what i saw 🙈🙈🙈🙈🙈

[@carburettorrebuildservice8964]

Good luck with this one, keep us posted on your progress.

[@djgeefunk4090]

Hi Gents i just received the cylinder head back today and all my parts to re-assemble and fit the engine i will keep you posted and make a video of the process and start up thank you very much for sharing build on this little engine...😂

[@carburettorrebuildservice8964]

@@djgeefunk4090 pleasure, i am glad the video helped you.

[@GenaEnSamIAm]

Baie dankie vir die video!! Good one!!

[@morrisjacobs4712]

Thanks for the information... I'm having the same problem right now where are you based? I have ford ikon 1.6 it does that when I'm stopping ✋ I will highly appreciate your feedback.

[@JacoBadenhorst]

Thanx for the video.

[@manuramkumar2590]

Thanks for the video. Great info 👍

[@bevanoneill9448]

It is what it is😎like a boss

[@kurtsmith1475]

Thanks oom. I have a bantam 1.3 shocking to see it has plastic chain tensioners. Irispective I enjoy its little performance. I would like to up the performance with a branch and free flow with maybe a piggy back ecu am I wasting my time ? Should I just drop another motor in ? I'f so what motor all comments are welcome.

[@carburettorrebuildservice8964]

Just go for a 1.6 Rocam engine, it will fit and you don't need to mod anything. On the 1.6 you can fit a branch and free flow

[@attiebuys7908]

Hi I whant to ask u why dus my Ford ka 1.3 oli pump broken in to small paese in side the oli pump were the pully goes in . What is the reason for that every month I must replace the pump

[@TrustMawarire]

Where are you located Wana bring my car

[@jpcoetzer3150]

Thank you

[@chayanpatchoo1238]

Where can I get all the engines torque Specs?

[@chittyshivaji4995]

Hi i had ford ikon 1.3 flair with 12kmpl. And radiation fan running continue.

[@managersamuel]

What causes over fuel on Rocam after engine rebuild? Mechanic is struggling

[@carburettorrebuildservice8964]

Hi, clean injectors, check TPO, check spark and look for air leaks

[@tapiwarwizi8461]

IS IT S0RTED YET

[@christianleshabane2655]

Hi sir I have Ford bantam rocam 1.6 can you redo engine for me ?

[@carburettorrebuildservice8964]

Hi, what is your location please?

[@jamezdice1]

Ja ek het dit ook al so gedoen my gat af tot daar I plan begin het om die motor te jack en nie die body nie en met 2 Jack's angle jy die motor af daai top mount af Baie makliker om in te Kom viral as jy groot ✋hande het

[@jacogooen144]

Hi my oom kan u my asb help, I'm rebuilding my rocam engine 1.3 petrol 2006 myself since I was robbed by so many previous macanics

[@carburettorrebuildservice8964]

Hi, how can i help you?

[@martingrung2228]

M

[@vhuranjero]

thank you