Parkside PERFORMANCE PWSAP 20 Li B2 vs MAKITA DGA504 angle grinder

Parkside PERFORMANCE PWSAP 20 Li B2
MAKITA DGA504 angle grinder
#Parkside
#Makita
#ForWorkAndFun
Support the Channel! - PAY PAL DONATE
www.paypal.com/donate/?cmd=_s...
Info Facebook
/ forworkandfun

[@Tomek1305w]

Makita 144 sztuk/5Ah=28,8 sztuk/Ah, Parkside 103/4Ah=25,75 sztuk/Ah. Wyniki bardzo podobne. Bład moze wynikać z napięcia odcięcia przez BMS i maksymalnego pradu ogniw 18650 w bateriach. Porównanie dla 4Ah: Makita 28,8 sztuk x 4Ah = 115,2 sztuk, Parkside dla 4Ah to 103 sztuki. Jednak delikatny plus dla makity

[@DonHrvato]

Parkside Performance are really good products, very happy with it

[@FORWORKANDFUN]

Yes, the performance is very good and so is the price.

[@joshh411]

Velmi dobré video, děkuji za recenzi. Parkside je dobrý, kvalitní, ale koupím Makitu... Parkside je dobrý i v případě koupě např. nové baterie, je o mnoho levnější, než jsou baterie od Makity. Takže kdo chce ušetřit, nebo nemá moc peněz, doporučuji Parkside.

[@marekuhrin156]

Díky za video. Rozmýšľam nad kúpou aku brúsky. Obával som sa že Parkside bude len hračka ale vypadá to fajn. Hlavne ta cena oproti Makite alebo Bosch je 3x menšia. Osobne sa mi osvedčili kotúče Dewald na nerez. Su síce drahšie ale fakt vydržia dosť.

[@FORWORKANDFUN]

Som rad že sa Vám video páčilo.Ak kúpite Parkside tak jedine čiernu Performance radu. Ja osobne mam aj Milwaukee.

[@tojajestemtu]

Poproszę o ten sam test z Twoją baterią 6Ah włożoną w Parkside Performance PWSAP 20 LI B2 (albo C3) vs Makita 504 DGA :)

[@martinmach2693]

Moje zkušenost s Parkside. Poslední 3 věci co jsem v lidlu koupil (i tuto flexu) jsem musel po pár měsících reklamovat. Vždy mi vrátili peníze. Makita - aku vrtačka co mám cca 10 let postavila 2 baráky a funguje furt skvěle.

[@FORWORKANDFUN]

Čauko dosť vecí aj mne pokazilo hlavne koncom minulého roka hádam každý 3ti produkt sa pokazil hneď po rozbaleni. No je to tak. Ale zase aku vŕtačka priklepova velka vrtacka u mňa tiež už postavila zatiaľ síce 1 dom ale predas stále funguje.

[@Compasscard]

The parkside one is now at 99€ with a charger and 4Ah battery. So it became more expensive but I believe it's still worth the money. Can't compare a rolls royce with a toyota neither.

[@FORWORKANDFUN]

Performance machines are very well used every day and without any problems even battery life is perfect.

[@ada2636]

Difference is small, price 1xMakita vs 3xParkside :) ( 5 years warranty for Parkside solves decisions what to choose )

[@12BlackKnight34]

Ziewa, skoro parkside jest taki och i ach to tylko czekać aż profesjonaliści przerzucą się masowo na ten chiński badziew.

[@sail5820]

Those are 3 years for the x20v team compatible equipment

[@FORWORKANDFUN]

If you need to work at home then Parkside. If on business so Makita.

[@Hazehellivo]

@@FORWORKANDFUN When working at home you dont need battery tools.

[@FORWORKANDFUN]

@@HazehellivoWhy? Not even a battery drill ??? It can already be seen that electric drills are no longer sold. people don't want to use them. This will gradually show up in the other tools. It is very good to use battery power tools even at home. You need to try and you will never want electricity again.

[@vittorio4109]

5ah versus 4ah.. it's normal thing. We should try the Parkside saw for 8 hours a day, i have a multitool of Parkside performance and i like it to much for the power, but i need to try this for sanding rusty railing corners for 8 hours.. 😁🤔

[@FORWORKANDFUN]

So show what you mean

[@vittorio4109]

@@FORWORKANDFUN I mean we should be try the Parkside for 8 hours a day, if the Parkside will good, it is a very good and affordable tool, sorry for my English.

[@FORWORKANDFUN]

@@vittorio4109 Unfortunately, I don't have time for such tests

[@stefanaleksandrov1684]

Makita is always better than Parkside but cordless Makita tools is expensive ,batteries too .I buy cheapest Makita corded tools they is on good prices (price is equal on expensive models Einhell) and works Great .Cordless tools I buy EInhell PXC Line because Batteries is very cheap -25euro 3Ah battery +charger ,and this tools is good enought for their price .One Makita battery price is equal on price to my brushless Einhell cordles drill+battery 3ah + charger.In my country Makita dont lower the price ,Bosch do.Sorry for my weak English.

[@zolika1993]

my corded bosch was like 40 euro and spins 11000.....

[@alex-UA-911]

Parkside нарахував: перший диск -49.5 різів,другий диск 60.5. І болгарку Ви зупинили самі. Вона могла ще зробити різи. Макіту любите?

[@joseplanellsmartinez]

Hola donde la compraste ?un saludo

[@FORWORKANDFUN]

Lidl Slovakia

[@Demolidor4ever]

1:51 it have the "head" broken!

[@kiaceed5966]

2:57 Jaký je rozdíl mezi akunářadím 18V a 20V ? Žádný 👍.

[@FORWORKANDFUN]

Presne tak.

[@user-lt2xr1xk7u]

Dejte děcku hračku ať se pohraje

[@G0WZB]

Makita had bigger battery, Id rather go for the cheaper parkside @£24.99 in the UK

[@FORWORKANDFUN]

Everything is cheaper in your country than in our country. And you make a lot more money than we do. And yet things are more expensive in our country

[@Nikola8000]

That's the reason am going for parkside. Those branded tools are expensive!

[@krtek673]

Zajímal by mě test nebo výdrž na 3Ah bateri u Makity...má někdo zkušenosti?

[@FORWORKANDFUN]

Treba rátať tak maximálne polovičný výkon na 1 nabitie . Podlá mňa je 3Ah malo na uhlovú brúsku mam osobne Milwaukee 5Ah batériami a aj tam sa žiada aspoň 8Ah .

[@krtek673]

@@FORWORKANDFUN No je mi jasný, že čím větší tím lepší pro brusku. Ale třeba já jsem si objednal sadu Aku vrtačky s příklepem a rozhodoval jsem se mezi 2x5Ah vs. 3x3Ah a nakonec jsem bral 3x3Ah, protože podle testu baterie vyšla poměrově doba práce/čas nabíjení nejlíp 3Ah..ta měla dobu práce cca 11min čistého času vůči 21min nabíjení a 6Ah byla 15min práce a 71min nabíjení. A zas mít na všechno milion baterek mi nepřijde ekonomické

[@ota2310]

18V a 20V nařadí je jedno a to samé stejný počet članku je to jen marketing lide si mysli ze 20V je lepší než 18V ale to je uplná blbost

[@PemoPL]

Z proporcji (144x4)/5=115 więc prawie tyle cięć wyszło.

[@FORWORKANDFUN]

Naprawdę dobry.

[@Vitbery]

Obě brusly jsou 20v Ale makita nepoužívá reklamní tah který klame zákazníky Proč je Parkside 20v? Protože když je plně nabitá měla by ukazovat kolem 20v To by ale měla ukazovat i Makita v nabitém stavu Jelikož napětí jednoho článku 18650 je 3,6-3,7v ale v nabitém stavu dosahuje až 4.2v

[@TipiDruhy]

Presne! A ono to potom trošku viac "sedí" aj s rozdielom v počte "odrezkov". Lebo skutočnosti parkside má 72Wh (pravdepodobne ešte o čosi menej - t.j. nemá 4Ah) a makita tých 90Wh, čo je rozdiel 25% (a nie 12,5 ako keby sme rátali s 80 vs 90Wh), čo je už predsa len bližšie k 39% (103 vs 144 rezov)...

[@lukeskywalker5358]

wyłączył szlifierkę Parkside i uznał, że Makita przecięła szybciej? :D

[@FORWORKANDFUN]

Nie Parkside uz mal vbibitu baterku

[@JanKowalski-sy4zh]

@@FORWORKANDFUN parkside ma ustawiny BMS w barerii na 16A. Jak przekroczysz ten prąd to się wyłączy. Wymień akumulatory na 18650 littokala 3400mA i BMS 20A. W tej samej obudowie będzie 6.8Ah i dużo więcej mocy. Parkside będzie lepszy od Makity. Parkside ma bardzo dobry silnik BLDC. Może dużo więcej, niesty akumulator od zielonej serii nie daje mu poszaleć :) Zdravím

[@FORWORKANDFUN]

@@JanKowalski-sy4zh JAK NAPRAWA Muszę wymienić ogniwa w akumulatorze?

[@JanKowalski-sy4zh]

@@FORWORKANDFUN jeśli chcesz większą pojemność to tak. Jeśli tylko zwiększyć oddawaną moc to wymiana BMS na bardziej wydajny. Lub poszukać straszej wersji akumulatora 5Ah. Tam wszytko było ok. Parkside zunifikował akumulatory serii zielonej i czarne,ze stratą dla czarnej. Dlatego seria Performance ma mniejszą pojemność i mniejszy prąd oddawany do urządzenia. Osobiście zmodyfikowałem na własne potrzeby aku 4Ah do drukując spodnią część obudowy akumultura i udało się upchnąć 10P4S i starcza naprawdę na długo. Prąd ustawiny mam na 30A. Szlifierka oddaje około 550W mocy co jest porównywalne ze słabszymi szlifierkami na 230V

[@FORWORKANDFUN]

@@JanKowalski-sy4zh Czy to nie jest na tym filmie?

[@alessiomenicucci7558]

Why you compare a 4000ma battery with a 5000ma? 144 pieces with 2 and a half disks vs 103 with 1 and a half that's interesting.

[@FORWORKANDFUN]

I didn't have the option to use a 4Ah battery for Makita. 2 drive for parkside would see only 10-20 cut and I would have to change.

[@NikosKourtzis]

If you put the mah into the equation, we should see something like 129 cuts from the Parkside if it could run on a 5000mah battery (or 115 from the Makita on a 4000mah battery). Not that huge of a difference between the two in terms of battery life.

[@Novy317]

A makita 2x is leallt mert ugy lemerult. A parkside meg nem is allt meg....

[@FORWORKANDFUN]

Mindkét masini jó

[@mr.pinter1080]

Végre magyar komment 🙂

[@banny123456]

ste lavak ? zaujimavy styl rezania, ne moc bezpecny.

[@FORWORKANDFUN]

Som pravak. A brúsku som držal dvoma rukami pevne. Spetny raz nehrozí keď brúsku držíš dvoma rukami.

[@banny123456]

@@FORWORKANDFUN to povedz tym co karboska vyskocila do stehna pri tomto obratenom rezani.

[@FORWORKANDFUN]

@@banny123456 Vyletí do stehna keď ju držíš pevne dvoma rukami . No neviem. Skôr si myslím že sa to môže stáť vtedy keď to držíš 1 rukou.

[@alesdonat787]

Co to je za nesmyslnej srovnavaci test? Testujete brusky nebo baterky?

[@FORWORKANDFUN]

Brusky ale aj efektivitu na 1 nabitie batérie. Myslím že pri nákupe akumulatoroveho náradia je dobré mať predstavu o vydrží batérie.

[@alesdonat787]

@@FORWORKANDFUN Tak byste mel srovnavat stejnou kapacitu ale... kdyz ma jedna baterka 4 Ah a druha 5 Ah, tak uz je od zacatku jasnej vysledek... :)

[@FORWORKANDFUN]

@@alesdonat787 To áno ale vieš si predsa vyrátať výkon na 1Ah alebo Wh. A hneď máš jasne čo vychádza lepšie.

[@alesdonat787]

@@FORWORKANDFUN no ale ty s vetsi kapacitou maji i vetsi vykon...

[@FORWORKANDFUN]

@@alesdonat787 Áno ale ti vravím že si vyrátaj koľko odrazkou spravila každá na 1Ah alebo na Wh. Nemajú väčší výkon iba väčšiu kapacitu batérie.

[@Sharan-to4tm]

Nejde porovnávat novou flexu Parkside se starou flexou Makita a že už má něco Makitka naběháno.... Vem si obě nové Aku Flexy a to i s bateriemi a pak porovnávej, Makita je jasný vítěz....

[@FORWORKANDFUN]

Ze ja víťaz Makita vidieť aj keď je stará predsa.

[@Sharan-to4tm]

@@FORWORKANDFUN 👍😉👍

[@FORWORKANDFUN]

Vo videu netvrdím ze je víťaz Parkside.

[@SQ6JNS]

Ta Makita to pogrom dla tego Parksa . Nawet nie ma czego porównywać. Nie ta klasa sprzętu.

[@mayo7982]

Majsterko. Naskor si zadavaž dostatocny pocet pocet ROVNAKÝCH kotucov. Potom sa postav k robote. Ale takto by to nejak malo vypadat, ktory stroj kolko zvladne.

[@FORWORKANDFUN]

Čauko kamarát každá masinka mala 2 rovnaké kotúče. Nerátal som že makita je schopná zodrat 3kotuce na 1 batériu. Do budúceho testu sa pripravím lepšie. Tie 0.8 mm kotúče sú drahé ale dobré.

[@mayo7982]

@@FORWORKANDFUN makita je best... ja ine nepouzivam...co sa tyka bateriek tak cena a zivotnost su bezkonkurencne...

[@FORWORKANDFUN]

Mne vadi na Makite tá rýchlo nabijacka je veľmi hlučná. Ináč je ok nemám žiadne výhrady.

[@mayo7982]

@@FORWORKANDFUN a mne tie pomale. Kes parkside 5ah nabijam 2h

[@FORWORKANDFUN]

@@mayo7982Nova Parkside nabíjačka ma 4,5Ah 120W a 4Ah batériu nabije za59 min

[@micjubba709]

Makita will beat Parkside all day long

[@92MICHALIS]

Sure not with same money parkside won makita 100 euro only the parkside and 5 years waranty

[@AndyRink]

The test is not correct. You compare a 5Ah battery with a 4Ah battery. That is a 20% difference in performance. In your first test alone, there were just under 40 cuts less than the Makita, there is a 21% difference. And Makita has also been restarted twice ... If you now keep the purchase price against it ... Makita 0 points, Parkside 1 point! The 2nd test would be similar. I don't compare a petrol engine with a diesel in terms of torque, do I? The test is not objective for me. Sorry.

[@FORWORKANDFUN]

I had no chance to get a 4Ah battery for Makita. And Parkside, after shutting down, bore in general. I'm not a professional comparison tool and so I do the test as much as I can. From the video you can but guess what the differences in the machines yes if the Parkside 5Ah battery performance was the same.

[@AndyRink]

Yes OK. I understand that. I didn't want to get too close to you either, but it comes across a bit wrong in the video. Nevertheless, you went out of your way to make a great video.

[@FORWORKANDFUN]

@@AndyRinkThank you for understanding. In the future, I will try to do the test evenly if possible.

[@juanmanuelgarciaortega2591]

Se te olvida un detalle, una cuesta 400 € y la otra 100€........ ante estos numeros el rendimiento queda en un segundo plano

[@LaRouchesupport]

Why only one disk spent then ??? I KNOW WHY, CAUSE U USED THICKER DISK, THAT WOULD EXPLAIN WHY PARKSIDE SEEMINGLY LOST , NO ??? YOU CHANGED THE DISK MR. 😂😂😂😂😂😂😂😂😂 😎 😉

[@FORWORKANDFUN]

No disk was the same 2x RHODUS 125x0.8 for makita and parkside only 3 disk was for makita different

[@imrichcsiba-csibasteel4890]

Nestačilo by ti ukázať čo sa stým dá rezať bez toho že by si to porovnával s profi náradím? Dúfam že keď budeš robiť test Milwaukee , tak tam nebudeš pchať hentake s...ky. Nevidel som celé video, lebo keď vidím to množstvo reklám, tak sa mi nechce , ale určite tab bude pár momentov , keď pílenie smerom od seba spôsobuje značné problémy. V Amerike nemajú radi takéto brúsky pretože ich nevedia držať. Keď si dáš rukoväť na opačnú stranu, tak zistíš že ti stačí aj jedna ruka.

[@FORWORKANDFUN]

Milwaukee bude až po novom roku. Reklamy vo videách jednoducho musia byt bez toho by nebola návratnosť . Iste vieš čo stoji 1 kotúč 0,8mm. Existuje KZbin Premium a mas to bez reklam.Rezať jednou rukou.... áno sú machri ktorí tak robia a skončili v nemocnici. Kde sa brúska sekne a chytí spetý raz tak ju máš v hlave. Je jedno do ktorej strany ju držíš hlavne ju treba držať dvomi rukami a aby iskri nešli na operátora. Ale máš pravdu lepšie sa reze kde je brúska opačne otočená. Rezal som tak preto aby som si nenarobil bordel v garáži.

[@FORWORKANDFUN]

Milwaukee budem porovnávať z viacerými pretože predajcovia hovoria že je to BEST TOOLS tak čakám že bude najlepšia.

[@imrichcsiba-csibasteel4890]

@@FORWORKANDFUN určite bude

[@FORWORKANDFUN]

@Imrich Csiba-CSIBASTEEL Za tu cenovku akú ma tak musí aj tu makitu poraziť nekompromisne.

[@radoslaw8444]

Makita ma aku lepszy.

[@FORWORKANDFUN]

Určite áno a hlavne vydrží niekoľko rokov.

[@gabbermaikel]

had to stop this video, cant take it serious as the operator dosnt know how to use a angle grinder. The way he uses this in the video is stupid and dangerous. He holds it upside down, meaning that if the thing bites it wil shoot the grinder right towards him. Yes its nice that the sparks dont fly towards you, but its even nicer if you dont have to catch a angle grinder with you face if something go's wrong. So learn how to use it first, then make youtube videos.

[@gabbermaikel]

o maaaan this gets better. He not only holds it wrong, but he is 1 of the guys that thinks he has to push on his grinder, then stalls the thing. That is operator failure right there. But then again, basics are allready wrong, what do you expect of the rest.

[@FORWORKANDFUN]

@@gabbermaikel Hi ..Nowhere in the operator's manual is written how to properly cut the grinder. However, the grinder has 3x handles on each side substantiating them so that the sparks carry on the operator and that the operator held the abrasive so that it can hold back once.

[@gabbermaikel]

@@FORWORKANDFUN cant make much of that sentence there. But the fact is that if the grinding disc bites in to the material in wich way wil the grinder then be pushed? Yes, towards the oprerator. So what wil happen if the grinder bites in the material? It wil come flying right at the operator. If you turn the grinder the other way around you wil have the grinder flying away from you if it bites. But if you use a knive do you cut towards yourself or away from yourself? Thats the same thing. Yes you can cut towards yourself, and it might be allright, till that 1 time it isnt, and then you're screwed. As for the sparks flying towards the operator. Yes that wil happen, but even the way you did it now some sparks wil fly towards the operator. That is why you have to wear proper clothing for the job. And if you adjust the guard properly the sparks wil be flying in to the guard for a big part and then flying out the front away from the operator again. And not only the sparks wil be held by the guard that way, but also the things why you should never run it without a guard. And that is the cutting disc IF it explodes. If the guard is adjusted properly the pieces of disc that could else hit you wil be flying in to the guard, and only the parts that would fly away from you can go past the guard. If you dont have the guard adjusted properly you might be catching the disc with your body, wich might kill you, or injure you severly. Google it, look how nice people look with a grinder cutting disc in their face. Then think again about handling a grinder without knowing how to because it is 1 of the most dangerous things you can have. Its probably 10 times more dangerous then a chainsaw and 100 times more dangerous then a circular saw.

[@FORWORKANDFUN]

@@gabbermaikelNicely written. Safety at work is 1 place

[@diesel-td1946]

E ci mancherebbe anche che non fosse meglio la Makita, costa 4/5 volte di più!