Full video

[@FLAlesslethal]

There's so much i disagree with on this mod. But im only going to say one thing. All that Vaseline is not at all fine. It will only collect all of the dirt, dust, plastic, aluminum and over time becoming thicker and thicker slowing everything down causing much friction. Open the marker up in 2 years and it will show but something tells me that you will have to anyway... Now, i have to say that i enjoy watching your videos and you are intelligent and i love what you do. I know that I learn something new everyday. Vaseline will stop a minor seal leak temporarily but that's all i use it for. Anyhow, still another great video and Godbless you My Friend! 🤟😎👉💨💥

[@noobt4eguns]

Thank you very much. You can watch my last video that i fix very dangerous issue the video last 2 hours. Brunox spray for air guns works best for the finger that rotate the magazine and i have video for it too

[@RafaelFerreira-b9f]

From 🇵🇹 Portugal 🇵🇹 very cool 👍👍

[@noobt4eguns]

Thank you. Also you can see my new video for HDR 68 i replace 2 o'rings in one day.Its similar video like this one

[@Rat_Batte]

This is the most complete video I've seen on upgrad HDR50 with the powerkit, thank you very much, know that it is also valid for HDR68. I haven't seen any other tutorials using products like vaseline, superlube, loctite..., it's meticulous work !

[@noobt4eguns]

Thanks my friend. 👍🏻 The HDR 68 have little tricky trigger

[@runerebel8441]

Nice video my friend. You got 230 fps on the first shot. Thats 20 joules. Very good power from the HDR50. Cheers 😃👍

[@noobt4eguns]

Thanks Rune. 👍🏻

[@Scottie1152]

Will you also do this for the HDR 68 please?

[@noobt4eguns]

I have video also for the HDR68 but no so good like the HDR50. On HDR68 the difficult part its the trigger

[@tomar777]

So, what difference does the shorter pin give? Is it worth it VS the stock pin?

[@noobt4eguns]

Stainless steel pin valve its better can protect the o'ring and the gun performs better.

[@tomar777]

@@noobt4eguns that's what HD24 says, ok, but difference in joules?

[@noobt4eguns]

The new pins have hole and may can put more co2 in the air chamber. The reason that i replace the pins to all of my guns its for Reliability. And can get some power

[@FLAlesslethal]

My bad bud but never finish working on your marker with it pressurized- A friend of mine nearly lost his hand and eye doing exactly what I just watched you do! I mean it. I would not just say that. And anyone who is paying close attention, im almost positive you just sprung a leak somewhere. Halfway through the process of screwing in the Clamshell it popped unless you are brewing tea in the background. Safety 1st!

[@noobt4eguns]

@@FLAlesslethal i do this over 30 times. I don't know what go wrong with the marker you said and am sorry for that😢

[@noobt4eguns]

@@FLAlesslethal when am working on the guns its no pressure in it. You must be sure that its not co2 capsule inside and you can see also from the release valve that the pin its inside

[@FLAlesslethal]

@@noobt4eguns did you not pressurize the marker before putting the Clamshell together?

[@juanmahernandez4683]

Hola…. Tendrá suficiente grasa ??? No será que le falte un poco más……

[@noobt4eguns]

kzbin.infoVmyGLfCzFMg?si=FLZJ_-Rik2PyvIEZ

[@Seabass1206]

vaseline could be dangerous if u use hpa

[@noobt4eguns]

Why? I see professionals in Taiwan put vaseline

[@Seabass1206]

@@noobt4egunsbecause under pressure those types of lubricants can ignite very easily just like how u can put oil on a pellet gun and it shoots crazy, it’s called dieseling, its best to use something non combustible

[@noobt4eguns]

@@Seabass1206 i use super lube in to Co2 tube and never had issues On the contrary, I can say that it is the best lubricant and I have never had ignition. I do not put Vaseline in place where the bullet comes into direct contact and I have done many tests with CO2 and HPA and in both cases the metal parts of the gun were cold. I don't know how to tell you about an air gun, I only know about the HDR I have 👍🏻Thank you for your comments happy new year my friend 🎄🇨🇾🌟👍🏻

[@kenturmon3660]

Omg seriously. Why not put the locktight on with a paint brush. Used way to much and vise grips cmon man.

[@Seabass1206]

its not like its made or carboard

[@noobt4eguns]

You can put loctite how you like

[@FLAlesslethal]

Check 44minutes and beyond you are tightening the quick pierce as hard as you can and then at 44m54s you actually pierce it and go "Boom" as if it was a joke. And after it was pressurized you beat that marker around with that screwdriver attempting to tighten the Clamshell back together. And im sorry but I can hear the leak as you are dropping things, freaking out as fast as you can to try and get it together. The markers on your wall look very unsafely. Whatever My Friend I wish you the best but you asked for it when you said " its good what do you think" at the end of the video 💥💥💥💨💨💨💨💨

[@noobt4eguns]

My dear friend thank you for your opinion but its normal to Pershing the cap with co2 to check if have leaks like every one do it.check the videos of Sean Kempter. Honestly this gun working very well until now and this gun its in my XM4 body kit and if you check my last videos you can see its working well. I don't know were you listening leaks when i put the plastic cover🤔. If was a leaks i will not put the plastic cover. I don't know if you understand that i am direct straight honest person and i make this video especially for people who don't know how to do what i do to the gun just to show the correct way. I respect your opinion for sure but i do this modification on this video correct. Honestly speaking i had accident with my HDB68 the co2 tube injured my head 10 stitches because i shot on 2000psi and 1500psi and because the umarex makes crimped valves. When this happens i make video to protect the people about the crimped valves and i didn't think about the Umarex quarantine i think about people safety first. Many people have same issue with that crimped valves but many of them after seeing my video they go fix or replace valves and that all its true.

[@FLAlesslethal]

@@noobt4eguns ofcourse it is. It just got to me that you you banging around with that screwdriver with it pressurized that's all. And I am so sorry for the hdb accident I was not aware of the facts. I had a similar, due to a manufacturing error. I just want us to practice safety. We are all in this together- keep in touch Fam! 🤟😎👉💨💥

[@noobt4eguns]

@FLAlesslethal what the difference is if you keep in your hand pressurized gun with half plastic cover and what if you keep it with both cover screwed?🤔

[@noobt4eguns]

@FLAlesslethal please i don't like when someone speaks lies for me. All my videos are true made with no editing and i don't have reason to show anything that its not true. Any time you can contact me for anything you like to ask and i can give you all my knowledge to pass afraid that markers.

[@FLAlesslethal]

@@noobt4eguns Listen, the marker had the CO2 pierced while you were screwing it together. I am no liar. Anyone can see you puncture the marker to check for leaks before you were done with it. Thats not safe, please don't message me anymore about it